Download Print this page

Haworth PREMISE CORNER UNIT Installation Instructions

Advertisement

Quick Links

PREMISE™ CORNER UNIT
Installation Instructions
Tools Required
Cross-recess (Phillips) screw driver
Level
Power Driver (optional)
Hex head driver
Corner Unit Assembly
1.
Place the corner top on a carpeted or padded
clean area of the floor with the holes facing up.
2.
Attach brackets to end panels using two (2)
#10 x 1-1/2 flat head screws per bracket (Fig. 1).
NOTE: When another unit will be adjoining the
opposite side of the end panel, center the bracket
on the end panel and use center two holes when
attaching bracket to the end panel (Fig. 2).
3.
Align bracket holes in the end panel with pre-
drilled holes on each end of corner top. Attach each
end panel using four (4) #10 x 1" truss head screws
(Fig. 3).
4.
Place outer leg, (glide facing up and solid wall
toward outer corner) onto corner top, aligning holes
in corner leg bracket with pre-drilled holes located
near outer corner of top. Attach outer corner leg to
top using four (4) #10 x 1-1/2" pan head screws
(Fig. 4).
#10 X 1"
TRUSS HEAD
SCREW (4)
FIG.3
CUSTOMER SERVICE PHONE: 1-800-426-8562
E.C.O. No:
263-168
#10 X 1-1/2"
FLAT HEAD
SCREWS
FIG.1
FIG.2
#10 X 1-1/2""
PAN HEAD
SCREW (4)
FIG.4
Pag e:
1 of 2
Par t No:
7021-6882
Rev .
5.
Slide the inner corner leg down into outer
corner leg. Align holes in inner corner leg with
holes in tab of outer corner leg nearest underside
of corner top. Fasten corner legs together using
four (4) #10 x 3/8" screws, two (2) at each end
(Figs. 5, 6).
6.
Position modesty panel between end panel
and the corner leg assembly, aligning slots in the
sides of each modesty panel with holes in corner
leg assembly, Use two (2) #10 x 3/4" pan head
screws to attached each modesty panel to end
panel. Use two (2) #10 x 3/8" pan head screws to
attach each modesty panel to the corner leg
assembly. Screw(s) must be aligned through
holes in both the inner and outer corner leg.
(Fig. 7). Repeat on other side.
7.
Turn unit over and attach necessary adjacent
unit(s) and level.
#10 X 3/8"
PAN HEAD
SCREW
FIG. 7
A
INNER LEG
#10 X 3/8" SCREW
(2) AT EACH END
FIG. 5
FIG. 6
MODESTY
PANEL(S)
#10 X 3/4"
PAN HEAD
SCREW
ALIGN HOLES IN
INNER AND OUTER
CORNER LEGS

Advertisement

loading
Need help?

Need help?

Do you have a question about the PREMISE CORNER UNIT and is the answer not in the manual?

Questions and answers

Summary of Contents for Haworth PREMISE CORNER UNIT

  • Page 1 PREMISE™ CORNER UNIT Installation Instructions Tools Required Slide the inner corner leg down into outer INNER LEG Cross-recess (Phillips) screw driver corner leg. Align holes in inner corner leg with Level holes in tab of outer corner leg nearest underside Power Driver (optional) of corner top.
  • Page 2 Assembly of Corner Unit to Bridge(s)/ Return(s) Caution: The corner unit must always be attached to at least one return. It is not a free- UNDERSIDE OF standing unit. RETURN/BRIDGE The corner unit may be used in an end condition or as a transitional unit (between return unit(s) and or UNDERSIDE OF FIG.