Subscribe to Our Youtube Channel
Related Manuals for Planet XGPL-16000
Summary of Contents for Planet XGPL-16000
- Page 1 16-Port XGS-PON OLT with 8-Port 10G SFP+ + 2-Port 100G QSFP28 XGPL-16000 Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Requirements ....................4 3. Hardware installation ..................5 3.1 Installing Redundant Power Supply Unit ............5 3.2 Removing Redundant Power Supply Unit ........... 6 4. XGS-PON OLT Management ................7 5. Terminal Setup ....................8 5.1 Logging on to the Console ............... -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET XGPL-16000 16-Port XG(S)-PON OLT. Unless specified, “XGS-PON OLT” mentioned in this Quick Installation Guide refers to the XGPL-16000. Open the box of the XGS-PON OLT and carefully unpack it. The box should contain the following items: z The XGS-PON OLT x 1 z QR Code Sheet x 1... -
Page 4: Requirements
For XG(S)-PON ONU, use an XGS-PON OLT Transceiver like PLANET XGPL-XGSFP-N1. For GPON ONU, use a GPON OLT Transceiver like PLANET GPL-GS- FP-C+. To connect an ONU, an appropriate OLT transceiver is required. Please ensure the selected transceiver meets PON specifications for compatibility and performance. -
Page 5: Hardware Installation
3. Hardware installation 3.1 Installing Redundant Power Supply Unit The XGPL-PWR150 is hot-swappable, so there is no need to power off the switch before removing the redundant power supply unit from the switch. The following installation uses the XGPL-PWR150-AC as an example. Follow these steps to install the redundant power supply unit in the switch: 1. Use a screwdriver to loosen and remove the screws to take off the blank plate. Figure 3-1: Removing the Blank Plate 2. -
Page 6: Removing Redundant Power Supply Unit
3.2 Removing Redundant Power Supply Unit Follow these steps to remove the redundant power supply unit from the switch: 1. Remove AC power cord from the XGPL-PWR150-AC. 2. To remove the redundant power supply unit from the XGPL-16000, use the handle to pull it out. The following images are based on the XGS-6350-48X2Q4C. The XGPL- 16000 can be used in the same way. -
Page 7: Xgs-Pon Olt Management
4. XGS-PON OLT Management To set up the XGS-PON OLT, the user needs to configure the XGS-PON OLT for network management. The XGS-PON OLT provides two management options: Out-of-Band Management and In-Band Management. Out-of-Band Management Out-of-band management is the management through console interface. Generally, the user will use out-of-band management for the initial switch configuration, or when in-band management is not available. -
Page 8: Terminal Setup
5. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to serial (console) port of the XGS-PON OLT. The console port of the XGS-PON OLT is DCE already, so that you can connect the console port directly through PC without the need of Null Modem. DB9 to RJ45 Serial Cable PC/Workstation with COM Port and... -
Page 9: Logging On To The Console
("x" means the last 6 digits of the MAC address. MAC:A8F7E0XXXXXX All characters should be in lowercase.) PLANET Technology Corp. Made in Taiwan Figure 5-3: XGS-PON OLT MAC ID Label Enter the default username and password, then set a new password according to the rule-based prompt and confirm it. -
Page 10: Configuring Ip Address
5.2 Configuring IP Address Management Port The IP address configuration commands for Management Port are listed below. Before using in-band management, the XGS-PON OLT must be configured with an IP address by out-of-band management (i.e. console mode). The XGS-PON OLT is shipped with a default Management Port IP address: 192.168.1.1/24. The configuration commands are as follows: Switch# config Switch(config)# interface g0/0/0 Switch(config-g0/0/0)# ip address 192.168.1.254 255.255.255.0 The previous command would apply the following settings for the XGS-PON OLT. IPv4 Address: 192.168.1.254 Subnet Mask: 255.255.255.0 Figure 5-5: Configuring IPv4 Address of Management Port Screen... -
Page 11: Changing Password
To check the current IP address or modify a new IP address for the XGS-PON OLT, please use the procedures as follows: Showing the Current IP Address 1. On “Switch#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address, subnet mask and gateway as shown in Figure 5-7. -
Page 12: Saving The Configuration
5.4 Saving the Configuration In XGS-PON OLT, the running configuration file stores in the RAM. In the current version, the running configuration sequence running-config can be saved from the RAM to FLASH by write command, so that the running configuration sequence becomes the start-up configuration file, which is called configuration save. Switch# write Figure 5-8: Write Screen 5.5 Configuring a PON Port for XGS-PON, XG-PON, or GPON ONUs... -
Page 13: Starting Web Management
6. Starting Web Management The following shows how to start up the Web Management of the Industrial L2+ Managed Switch. Note the Industrial L2+ Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the IP address of the XGS-PON OLT is 192.168.1.1 on Management Port, then the manager PC should be set to 192.168.1.x (where x is a number between 2 and 254, except 1), and the default subnet mask is 255.255.255.0. -
Page 14: Saving Configuration Via The Web
3. After entering the password, the main screen appears as shown in Figure 6-3. Figure 6-3: Web Main Screen of XGS-PON OLT 4. The Switch Menu on the left of the Web page lets you access all the commands and statistics the Switch provides. Now, you can use the Web management interface to continue the Switch management or manage the XGS-PON OLT by console interface. Please refer to the user manual for more. - Page 15 Press “OK” button to save current running-configuration to start up configuration.
-
Page 16: Recovering Back To Default Configuration
7. Recovering Back to Default Configuration Reset the XGS-PON OLT to factory default settings: 1. Reboot the device by immediately pressing “Ctrl + P” to enter the Monitor Mode when the boot screen appears. Figure 7-1: Entering Monitor Mode 2. In the Monitor Mode, execute the following command to erase the current config- uration: Figure 7-2: Formatting Flash to Restore Factory Defaults 3. After the formatting process is complete, reboot the device by entering: Figure 7-3: Rebooting the Device After Formatting 4. The system will restore the factory default settings. The management IP will be reset to “192.168.1.1/24”, and the default login credentials will be restored. -
Page 17: Customer Support
8. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw XGPL-16000 User’s Manual https://www.planet.com.tw/en/support/download.php?view=3&key=XGPL-16000#list Copyright © PLANET Technology Corp. 2025. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Need help?
Do you have a question about the XGPL-16000 and is the answer not in the manual?
Questions and answers