Related Manuals for Planet XGS3-24242
Summary of Contents for Planet XGS3-24242
- Page 1 Layer 3 24-Port Gigabit TP/SFP + 4-Port 10G SFP+ Stackable Managed Switch XGS3-24242 Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Switch Management ..................4 3. Requirements ....................5 4. Terminal Setup ....................6 4.1 Logging on to the Console ............... 7 4.2 Configuring IP Address ................9 4.3 Setting 1000BASE-X for SFP+ Port ............10 4.4 Setting 100BASE-FX for SFP Port ............10 4.5 Saving the Configuration ............... -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET XGS3-24242 Managed switch. The description of this model is shown below: Layer 3 24-Port 100/1000X SFP + 8-Port Shared TP + 4-Port XGS3-24242 10G SFP+ Stackable Managed Switch “L3 Managed Switch” is used as an alternative name in this Quick Installation Guide. Open the box of the L3 Managed Switch and carefully unpack it. The box should... -
Page 4: Switch Management
2. Switch Management To set up the L3 Managed Switch, the user needs to configure the L3 Managed Switch for network management. The L3 Managed Switch provides two management options: Out-of-Band Management and In-Band Management. Out-of-Band Management Out-of-band management is the management through Console interface. Generally, the user will use out-of-band management for the initial switch configuration, or when in-band management is not available. -
Page 5: Requirements
3. Requirements z Workstations running Windows 7/8/10/11, macOS 10.12 or later, Linux Kernel 2.6.18 or later, or other modern operating systems are compatible with TCP/IP Protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. -
Page 6: Terminal Setup
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to serial (console) port of the L3 Managed Switch. The console port of the L3 Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of Null Modem. -
Page 7: Logging On To The Console
4.1 Logging on to the Console Once the terminal is connected to the device, power on the L3 Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks for the login user name and password. The factory default user name and password are as follows as the login screen in Figure 4-3 appears. The following console screen is based on the firmware version before May of 2024. - Page 8 (2) This device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan PLANET Technology Corp. Figure 4-4: Managed Switch MAC ID Label Enter the default username and password, then set a new password according to the rule-based prompt and confirm it. Upon success, press any key to return to the...
-
Page 9: Configuring Ip Address
To check the current IP address or modify a new IP address for the L3 Managed Switch, please use the procedures as follows: Show the current IP address 1. On “XGS3-24242(config)#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address shown in Figure 4-7. Figure 4-7: Showing IP Information Screen If the IP is successfully configured, the L3 Managed Switch will apply the new IP address setting immediately. You can access the Web interface of L3 Managed... -
Page 10: Setting 1000Base-X For Sfp+ Port
The L3 Managed Switch supports both 10GBASE-X SFP+ transceiver and 1000BASE-X SFP transceiver by manual setting and the default SFP+ port speed is set to 10Gbps. To establish the fiber connection with 1000BASE-X SFP transceiver, the following command configuration is required: XGS3-24242#config XGS3-24242(config)#interface ethernet 1/0/25-28 XGS3-24242(config-if-port-range)#speed-duplex force1g-full Figure 4-8: Setting 1000BASE-X Screen 4.4 Setting 100BASE-FX for SFP Port The L3 Managed Switch supports both 1000BASE-X and 100BASE-FX SFP transceivers by manual setting and the default SFP port speed is set to 1000Mbps. -
Page 11: Saving The Configuration
RAM to FLASH by write command or copy running-config startup- config command, so that the running configuration sequence becomes the start-up configuration file, which is called configuration save. XGS3-24242#copy running-config startup-config Figure 4-10: Copying Running-config Startup-config Screen... -
Page 12: Starting Web Management
5. Starting Web Management The L3 Managed Switch provides a built-in browser interface. You can manage it remotely by having a remote host with Web browser, such as Mozilla Firefox, Google Chrome or Apple Safari. PC / Workstation with Web Browser 192.168.0.x Managed Switch RJ45/UTP Cable IP Address: 192.168.0.100 Figure 5-1: IP Management Diagram The following shows how to start up the Web Management of the L3 Managed Switch. Please note the L3 Managed Switch is configured through an Ethernet connection. -
Page 13: Logging In To The L3 Managed Switch
5.1 Logging in to the L3 Managed Switch 1. Use Internet Google Chrome or above Web browser and enter IP address https://192.168.0.254 to access the Web interface. The following console screen is based on the firmware version before May of 2024. 2. When the following dialog box appears, please enter the configured username “admin” and password “admin” (or the username/password you have changed via console). The login screen in Figure 5-2 appears. - Page 14 (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. PLANET Technology Corp. Made in Taiwan Figure 5-3: Industrial Managed Switch MAC ID Label Figure 5-4: Login Screen 6. After logging in, you will be prompted to change the initial password to a perma-...
- Page 15 7. Enter the default username and password, then set a new password according to the rule-based prompt and confirm it. Upon success, press any key to return to the login prompt. Log in with "admin" and the “new password” to access the Web interface. Figure 5-6: Web Main Screen of L3 Managed Switch 8. The Switch Menu on the left of the Web page lets you access all the commands and statistics the Switch provides. Now, you can use the Web management interface to continue the Switch management or manage the L3 Managed Switch by console interface. Please refer to the user manual for more.
-
Page 16: Saving Configuration Via The Web
5.2 Saving Configuration via the Web In the L3 Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by “Save current running-configurations” function, so that the running configuration sequence becomes the startup configuration file, which is called configuration save. -
Page 17: Recovering Back To Default Configuration
10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. Reset Button Console MGMT 115200,N,8,1 Reset MGMT Figure 6-1: XGS3-24242 Reset Button... -
Page 18: Customer Support
7. Customer Support TThank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support@planet.com.tw XGS3-24242v3 User’s Manual https://www.planet.com.tw/en/support/download. php?&method=keyword&keyword=xgs3-2&view=3#list (Please select your switch model name from the Product Model drop-down menu) Copyright © PLANET Technology Corp. 2024.
Need help?
Do you have a question about the XGS3-24242 and is the answer not in the manual?
Questions and answers