Summary of Contents for GIGACLOUD TECHNOLOGY N709P195997
Page 1
ASSEMBLY INSTRUCTIONS INSTRUCTIONS DE MONTAGE TWIN/TWIN BUNK BED WITH DESK, STAIRS Please feel free to contact us if you have any questions Email: hd.team@qualfurn.net N709P195997/N709P195998/N709P195999...
Page 2
SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE UPPER EDGE OF GUARDRAILS. Replacement Parts: Replacement Parts, including additional guardrails, may be obtained from any of our (GIGACLOUD TECHNOLOGY (USA) INC. 4388 SHIRLEY AVE, EL MONTE, CA 91731) dealers.
Page 3
LA TAILLE DOIT LA SURFACE DU MATELAS DOIT AU MOINS 5" (127 MM) EN DESSOUS DU de rechange, y compris les garde-corps peuvent obtenues de l'un de nos revendeurs (GIGACLOUD TECHNOLOGY (USA) INC. 4388 SHIRLEY AVE, EL MONTE, CA 91731).
Page 5
Part List N709P195997 Upper horizontal bar HB - 3pcs Leg (Left Back) - 1pc Leg (Left Front) - 1pc Pied (Avant gauche) Lower horizontal bar HB - 1pc Leg (Right Back) - 1pc Leg (Right Front) - 1pc Pied (Avant droit)
Page 6
Part List N709P195998 + Hardware inside / Upper horizontal bar (Back) - 1pc Vertical guard rail FB - 1pc Vertical guard rail - 2pcs Garde-corps vertical FB Garde-corps vertical Upper horizontal bar (Front) - 1pc Vertical bar (Left Front)- 1pc Vertical bar (Left back)- 1pc Barre verticale (Avant gauche) Barre verticale...
Page 7
Part List N709P195999 Upper horizontal bar - 2pcs Divider horizontal bar - 3pcs Slats - 11pcs Latte Top panel - 2pcs Upper horizontal bar - 2pcs Lower horizontal bar - 2pcs Panneau du haut Side panel - 4pcs Upper back panel - 2pcs Lower back panel - 1pc Door (left) - 1pc Door (right) - 1pc...
Page 8
Hardware List N709P195998 Liste des Accessoires 8*30mm Wood dowel (8pcs) Wood dowel (46pcs) Hex-Head bolts (16pcs) hexagonale Cheville en bois Cheville en bois 60mm 40mm Hex-Head bolts (31pcs) Hex-Head bolts (69pcs) Hex-Head bolts (8pcs) hexagonale hexagonale hexagonale 1/4"*15 (9.5mm) Hex-Head bolts (17pcs) Hex-Head bolts (18pcs) Horizontal-Hole bolts(114pcs) hexagonale...
Page 9
L58*51*12mm Sliding wheel (4pcs) Metal bracket (2pcs) Metal bracket (1pc) Roue coulissante (1/4")4.5*58mm Allen key (1pc) Metal bracket (1pc) ASSEMBLY TOOLS REQUIRED ( NOT INCLUDED ) OUTILS D'ASSEMBLAGE REQUIS (NON INCLUS)
Page 10
STEP 1: 8PCS 8PCS Note:Part 8 will face up with the "x" mark on it, otherwise it cannot be tightened Remarque: 8 sera face vers le haut avec la marque "x" STEP 2: 6PCS 6PCS...
Page 14
STEP 9: 4PCS Note: Place hardware #20 with the "X" face outward, and make sure that the arrowhead is upward. Then, place hardware #20 into the hole of hardware #19 and tighten it clockwise with a hand screwdriver. (Please do NOT use an electric screwdriver.) STEP 10: 8PCS...
Page 20
STEP 24: STEP 25: 4PCS 4PCS Note:Part 8 will face up with the "x" mark on it, otherwise it cannot be tightened Remarque: 8 sera face vers le haut avec la marque "x"...
Page 39
STEP 62: 42PCS 3.1" 3.3" 2.4" 79mm 84mm 61mm NOTE: Please make sure the bed slats close to the side rail before locking the screws to avoid breakage. This step is required for both the left and right sides. Moreover, please do not lock the screws of the bed slats at the outermost edge to avoid damaging.
Need help?
Do you have a question about the N709P195997 and is the answer not in the manual?
Questions and answers