Download
Share
Print this page
Elkay LZ Series Installation & Use Manual
  1. Manuals
  2. Brands
  3. Elkay Manuals
  4. Plumbing Product
  5. LZ Series
  6. Installation & use manual
Elkay LZ Series Installation & Use Manual

Elkay LZ Series Installation & Use Manual

Bottle filling stations & coolers, smart connected-ready
Hide thumbs Also See for LZ Series:

Advertisement

Quick Links

Download this manual
ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A
LZ
*Versatile cooler design allows units to be installed either left-hand high and right-hand low or left-low and right high.
Basin change may be required. See desired rough-in to help determine if the basin change is necessary.
Important: The refrigerated coolers must be hung on the right side.
Patent zurn-elkay.com/patents
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov
Enhanced
INSTALLATION & USE MANUAL
Series Bottle Filling Stations & Coolers
™
SMART CONNECTED-READY
Pre-installation steps
Install Zurn Gateway and Register Product in
plumbSMART
1. Install Zurn Gateway (required and sold
separately) per the gateway instructions
manual, if an existing gateway is not within
communication range.
2. Be sure the gateway is powered on and
c o n n e c t e d ( p e r g a t e w a y i n s t a l l a t i o n
instructions) prior to installing your bottle
filler. Serial number located on back of the
Gateway, is required to register the gateway
to your tenant.
3. If you have not already set up an tenant
account and your administrator access,
request at 844-987-67 37 or
zurnconnectedproducts@zurn.com
4. Log into plumbsmart.zurn.com
5. Register Connected product in plumbSMART
using plumbSMART Registration ID located
on plumbSMART ID Registration Label, (See
Fig. 11a, Pg. 8). (Watch How-To videos to get
started. Located in the support section inside
the portal.)
Page 1
2000002265 (Rev. B - 02/25)

Advertisement

loading
Need help?

Need help?

Do you have a question about the LZ Series and is the answer not in the manual?

Questions and answers

Related Manuals for Elkay LZ Series

Summary of Contents for Elkay LZ Series

  • Page 1 Basin change may be required. See desired rough-in to help determine if the basin change is necessary. Important: The refrigerated coolers must be hung on the right side. Patent zurn-elkay.com/patents WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov...
  • Page 2 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A FIG. 1 2000002265 (Rev. B - 02/25) Page 2...
  • Page 3 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A FIG. 2 Page 3 2000002265 (Rev. B - 02/25)
  • Page 4 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A FIG. 3 2000002265 (Rev. B - 02/25) Page 4...
  • Page 5 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A FIG. 4 Page 5 2000002265 (Rev. B - 02/25)
  • Page 6 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A INSTRUCTIONS FOR REMOVING WRAPPER Fig. D(i) Fig. D(ii) 1) Remove the two security screws (size T25) from the front panel. (see Fig D(i)). NOTE: SCREW THREADS INTO BUSHING WHILE ANGLED. DO NOT ATTEMPT TO THREAD SCREW INTO BUSHING HORIZONTALLY. 2) Gently pull the wrapper down and rotate the wrapper to a downward position (see Fig D(ii)).
  • Page 7 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Fig. F Fig. E Fig. F NOTE: NOTE: The highlighted portion in red color is acceptable plumbing rough-in for To mitigate the wrapper rotation interferences, zip tie lines (plumbing and installation. electrical) running between the cooler units to the waste line (PVC pipe). HANGER BRACKETS INSTALLATION 1) Remove hanger bracket fastened to back of coolers by removing one (1) screw.
  • Page 8 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A BOTTLE FILLER INSTALLATION 14) Remove two (2) mounting screws with 5/32” Allen wrench holding Bottle Filler to wall mounting plate (See Fig. 8). Note do not discard mounting screws, they will be needed to secure Bottle Filler to wall mounting plate. 15) Remove wall mounting plate from Bottle Filler (See Fig.
  • Page 9 7) Connect electrical power by plugging in unit’s power cord. 8) Turn on water supply and Run water and flush filter to purge air and fine carbon particles from filter before use. Visit elkay.com/filtration for additional details. Also run water through bottle filler until all air is removed and water flow is clear.
  • Page 10 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A CONFIGURATION INSTRUCTIONS INSTRUCTIONS TO MOVE THE BOTTLE FILLER & BASIN TO THE LEFT SIDE (NON-REFRIGERATED) FOR ALTERNATE MOUNTING VERSATILE BI-LEVEL NOTE: TO COMPLETE THIS OPTION, THE VERSATILE BF BASIN KIT (VERSATILEBFKIT) MUST BE ORDERED SEPARATELY. Fig. A Fig.
  • Page 11 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Refrigerated Cooler side: Carefully lift and tip the shroud/basin assembly off the cooler frame. Only disconnect the (2) black wires coming from the shroud assembly that go to the solenoid valve and to the cold control. Disconnect the water line at the solenoid valve.
  • Page 12 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A PLUMBING DIAGRAMS VERSATILE BI-LEVEL Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain 2000002265 (Rev. B - 02/25) Page 12...
  • Page 13 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Versatile Wrapper Installation Instructions Right Hand Wrapper (Low Side) 1) Remove the (2) screws from the wrapper, rotate the wrapper down, and remove. 2) Clip cover plate, sliding until plate sits flush with the wall. 3) Re-install wrapper with (2) screws. 4) Dispose of unused trim piece.
  • Page 14 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Versatile Wrapper Installation Instructions continued. . . Instrucciones de instalación de envoltura versátil continuadas. . . Instructions d’installation de l’enveloppe polyvalente (suite). . . Wrapper Fill Left Hand Wrapper (Low Side) Piece Location 1) Remove the (2) screws from the wrapper, rotate (Right Side High) the wrapper down, and remove.
  • Page 15 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A 115V Refrigerated Wiring Diagram with Alpha/Numeric Display Connect-Ready - Enhanced Bottle Filler Wire harness End-point Board Fig. 19 WARNING • INGESTION HAZARD: This product contains a button cell or coin battery. • DEATH or serious injury can occur if ingested. •...
  • Page 16 Blue indicates normal operation, no immediate attention needed. Red indicates immediate attention required to maintain proper function. Scan for trouble shooting and to sign up for auto Fig. 23 replenishment of authentic Elkay filters. WATERSENTRY Filter Detail ® WATERSENTRY FILTER PARTS LIST ®...

  • Page 17: Temperature Control

    ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Refrigerated Unit Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove two (2) screws from front of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
  • Page 18 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A 2000002265 (Rev. B - 02/25) Page 18...
  • Page 19 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A Pictured is unit only without bottle filler. Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A See Fig. 25 12, 13 See Fig. 24 12, 13 Fig.
  • Page 20 ENLZSTL8WSAP-W1_1A, ENLZSTL8WSMP-W1_1A, ENLZSTL8WSSP-W1_1A ATTENTION: If the product serial number is before 190424189, please refer to archived documents section of Elkay.com for the most accurate parts list. (www.elkay.com/archived-documents) 115V PARTS LIST / LISTA DE PIEZAS DE 115 V / LISTE DES PIÈCES 115 V...

  • Page 21: Fcc Compliance Statement

    Kit - Conjunto de válvula solenoide Trousse - Assemblage électrovanne 2000002090 Nameplate - Elkay Filtered (AW) Placa de identificación: Elkay con filtro (AW) Plaque signalétique - Elkay à filtre (AW) 2000002089 Nameplate - Elkay Filtered (MB) Placa de identificación: Elkay con filtro (MB) Plaque signalétique - Elkay à...
  • Page 22 IMPRESO EN LOS E.E.U.U. INFORMATIONS POUR LE SERVICE PAR NUMERO SANS FRAIS 1.800.260.6640 IMPRIMÉ AUX É.-U. ELKAY MANUFACTURING Co. • 1333 BUTTERFIELD ROAD SUITE 200 DOWNERS GROVE, IL 60515 USA - • 630.574.8484 • www.elkay.com 2000002265 (Rev. B - 02/25) Page 22...

This manual is also suitable for:

Lzstl8wsap-w1Lzstl8wsmp-w1Enhanced lz series