StarTech.com 1G-NETWORK-ISOLATOR Quick Start Manual page 2

2. Mount the Networking Isolator by inserting the Mounting Plate onto the DIN Rail
at an angle, starting from the top then push against the DIN Rail. (Figure 2)
Surface Mounting (optional)
1. Remove one of the protective backings from the Adhesive Strip.
2. Attach the Adhesive Strip to the back of the Network Isolator by applying light
pressure for a few seconds.
3. Remove the remaining protective backing from the Adhesive Strip.
4. Firmly attach the Network Isolator to a clean flat surface.
Figure 1
Figure 2
Regulatory Compliance
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a different circuit than the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the device. If shielded interface cables are included with the product, or if additional components or accessories
are designated for use with the installation, they must be used to ensure compliance with FCC regulations.
ISED Statement / Déclaration d'ISDE
CAN ICES-003(B) / NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
EU CE EMC/EMI
StarTech.com hereby declares that this device complies with the Electromagnetic Compatibility Directive (EMC).
A copy of the EU Declaration of Conformity is available at
Support tab.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes
only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to
which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related
documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
FR
StarTech.com Ltd. StarTech.com LLP
45 Artisans Crescent 4490 South Hamilton
London, Ontario Road
N5V 5E9 Groveport, Ohio
Canada 43125
U.S.A.
Quick-Start Guide
www.StarTech.com/1G-NETWORK-ISOLATOR under the Product
www.startech.com/warranty
FR
À DÉPOSER À DÉPOSER
Cet appareil,
EN MAGASIN EN DÉCHÈTERIE
ses accessoires
et cordons
OU
se recyclent
Points de collecte sur www.quefairedemesdechets.fr
Privilégiez la répara�on ou le don de votre appareil !
StarTech.com Ltd. StarTech.com Ltd.
Unit B, Pinnacle 15 Siriusdreef 17-27
Gowerton Road 2132 WT Hoofddorp
Brackmills, The Netherlands
Northampton
NN4 7BW
United Kingdom
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp