Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for atomi smart Nouvo3
Summary of Contents for atomi smart Nouvo3
- Page 1 Installation Guide Nouvo Smart Flush Mount Ceiling Fan AT2480...
-
Page 2: For Your Safety
FOR YOUR SAFETY Read and save all instructions before using. WARNING 1. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades. 2. -
Page 3: What's In The Box
WHAT’S IN THE BOX Ceiling Fan Fan Blade (x3) Acrylic Shade Light Fixture This fixture comes pre-assembled. Please, check step 2 on page 15 for instructions. Bag D Light Ring LED Board Motor Cover Wire Nut (x3) Mounting Bracket Accessory Blades Accessory Bag Bag B1 Bag B2... -
Page 4: Tools Needed For Installation
TOOLS NEEDED FOR INSTALLATION Ladder Screwdriver Wire strippers Drill (If applicable) (If mounting to a support structure or concrete. Only concrete-compatible screws are included.) SELECT YOUR INSTALLATION LOCATION Measure room dimensions 30in. from blade tip to nearest wall or 7ft. from bottom edge of obstruction blade to the floor Check the outlet box... - Page 5 Mounting Box If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box, then read the following instructions. • Disconnect the power by removing fuses or turning off circuit breakers. • Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. •...
-
Page 6: Installing The Standard Bracket
ATTENTION Only use the provided Atomi Smart ceiling bracket that comes with your fan. Remove any existing brackets from your ceiling prior to installation. Secure the bracket to a ceiling box that is acceptable for fan support of 31.8kg (70lb). - Page 7 INSTALLING THE SAFETY SUPPORT (PART ONE) Place the washer onto the wood screw and pass the Install the screw with washer through an unused slot screw through one of the loops on the safety cable. in the bracket at the outermost end of the slot. Ensure that the screw passes OUTSIDE of the fan mounting box in the ceiling and that it does not contact any wires entering/exiting the fan mounting box.
-
Page 8: Wiring The Fan
FOR THIS STEP YOU WILL NEED WIRING THE FAN Carefully follow these steps to get your fan wired safely and quickly. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. THE CEILING FAN MUST BE GROUNDED. WIRING MUST BE UP TO CODE. - Page 9 Push the bare metal ends of the wires together and slide a wire nut over them. Twist the wire nut clockwise until tight. Give it a gentle pull to ensure none of the wires come apart. Connect the BLACK Connect the WHITE (W) wire Connect the GREEN (ungrounded Z) wire from the from the RECEIVER to the...
- Page 10 INSTALLING THE SAFETY SUPPORT (PART TWO) Install the second part of the safety cable. Place the motor cable through one hole in Then place the motor cable through one the dual cable clamp. loop of the safety cable.
- Page 11 Loop the safety cable through the other hole of Use a screwdriver to tighten each screw at the dual cable clamp and feed the cable all the the end of the dual cable clamp. way through.
-
Page 12: Securing The Fan
SECURING THE FAN Tuck wires into the motor housing unit and avoid pinching wires. Then attach the motor assembly by twist-locking the fan in place using the two screws in the L-slots. Install the other two screws that are not in the L-slots. -
Page 13: Installing The Motor Cover
INSTALLING THE MOTOR COVER Align the arrow with one of the screw stud posts. Next, push up and twist to the right and secure the cover in place. -
Page 14: Installing The Blades
FOR THIS STEP YOU WILL NEED INSTALLING THE BLADES Place each fan blade on the face of the motor plate one at a time. Secure each blade with screws found in Bag A1. Note: • Do not install the fan blades behind the motor plate. -
Page 15: Assembling The Light Fixture
FOR THIS STEP YOU WILL NEED ASSEMBLING THE LIGHT FIXTURE Detach the LED board from the light ring using a screwdriver. Note: Save these screws to be used in step 4. Remove one light housing screw. Loosen the other two screws but do not remove. - Page 16 Align the light ring keyhole slots over the two screws and twist. Re-install the light housing screw that was removed and tighten the other screws in the keyhole slots.
- Page 17 Connect the white plug from the housing structure to Attach the LED board cover using the four screws the white plug from the LED board. removed (explained in step 1). Do not press the LEDs on the Check that LEDs are not LED board when connecting crimped by the LED board the plug.
- Page 18 Turn on the circuit breakers to the outlet box associated with the wall switch location, then turn on the wall switch and check if the Atomi Smart WiFi Ceiling Fan has 100% of white light brightness. You can check the brightness using the Atomi Smart app or with the included remote controller.
- Page 19 Scan the QR code below Register or go to https:/ /atomismart.com/app/ Get the app Register Download the Atomi Smart app from Follow the on-screen instructions and the App Store or Google Play. register an account. Make sure to allow access to Location (Android), Bluetooth and Local Network (iOS).
- Page 20 WiFi Password Continue Connect your 2.4GHz WiFi network* Enter or select your local WiFi name, enter your password, then press “Continue”. *Make sure you’re connected to a 2.4GHz WiFi network (Atomi Smart can’t connect to 5GHz networks).
-
Page 21: Using The Remote Control
FOR THIS STEP YOU WILL NEED USING THE REMOTE CONTROL Control buttons WiFi pairing: long press (more than 5 seconds) to connect fan to network. Short press to recover WiFi connection Fan ON/OFF Long press (10 seconds) Fan reversal: Press to change to turn WiFi OFF the direction of the airflow Fan Speed (from 1 to 6) - Page 22 ATTACHING TO AN EXISTING LIGHT SWITCH Note: This is only compatible with toggle switches. Remove the screws from your Place the remote control mount Slide the remote control light switch cover over the cover and attach it with the holder in place, then insert the (Do not remove the cover).
- Page 23 FOR THIS STEP YOU WILL NEED USING THE BALANCE KIT Follow these steps to properly even out the blade weight distribution. Pause your fan to attach the clip to the end of any Ensure your fan is correctly installed and all fasteners are secure.
-
Page 24: Troubleshooting
The Ceiling Fan is too noisy. Use your smartphone to confirm that you have at least two WiFi bars in the vicinity of your Atomi Smart device. Confirm that the blades are properly installed. If not, move your Atomi Smart device closer to your The Ceiling Fan is wobbling. - Page 25 How to use batteries for the remote control? How to pair the remote control? • Always purchase the correct size and grade of the Once connected to the app, turn off the wall switch battery most suitable for the intended use. and wait 20-30 seconds.
- Page 26 1. Coupon is only valid on the Atomi Smart website 8. Promo code is not exchangeable for cash. www.atomismart.com. 9. Atomi Smart will not be liable and/or be required to 2. A valid code must be entered at the checkout page offer replacement codes, discounts, credits, cash or in order to redeem the promotion.
- Page 27 For questions or concerns, email us at support@atomiusa.com Manufactured and marketed by ATOMI INC. 10 WEST 33RD ST., NEW YORK, NY 10001 atomi smart is a registered trademark of Atomi Inc. ® Designed by Atomi in New York. Made in China...
Need help?
Do you have a question about the Nouvo3 and is the answer not in the manual?
Questions and answers