NAIM ACTIVE Manual
  1. Manuals
  2. Brands
  3. NAIM Manuals
  4. Crossover
  5. ACTIVE
  6. Manual
NAIM ACTIVE Manual

NAIM ACTIVE Manual

Active crossovers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
O W N E R S
M A N U A L
A c t i v e C r o s s o v e r s

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ACTIVE and is the answer not in the manual?

Questions and answers

Related Manuals for NAIM ACTIVE

Summary of Contents for NAIM ACTIVE

  • Page 1 O W N E R S M A N U A L A c t i v e C r o s s o v e r s...

  • Page 2: Equipment Installation

    Appropriate Standards 1.0 Equipment installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way.

  • Page 3: Getting Started

    Legal consumer protection varies from country to country. In most territories a dealer must be prepared to take back any Naim equipment he has sold you if he cannot make it work to your satisfaction in your own home. A problem may be due to a fault in any part of the system or its installation so it is essential to make full use of your local dealer’s...
  • Page 4 If there is a known problem in your locality it is advisable to arrange for a home demonstration before purchase to find out if Naim equipment is likely to be affected. Susceptibility to radio frequency interference is related to the wide internal bandwidth necessary for high sound quality.

  • Page 5: Mains Lead

    4.3 fuse carrier Should the plug fuse carrier be damaged or lost, the correct replacement must be obtained from your dealer or from Naim direct. Do not use the plug until the fuse carrier is replaced. 4.4 plug fuses Replace only with ASTA or BS 1362 approved fuses.
  • Page 6 Output level adjustment for low and high frequency sections is available within a snaxo 3-6. As delivered, the level adjustment is set nominally o/p1 o/p1 flat for appropriate Naim loudspeakers. Contact your dealer for further o/p2 information. snaxo 2-4 active crossover 2 &...
  • Page 7 snaxo connection to hi-cap from nac 52 and supercap to nac 52 link plug fitted snaxo connection to supercap from nac 52 and supercap to nac 52 link plug removed...
  • Page 8 snaxo connection to hi-cap from nac 82 and two hi-caps to nac 82 note If the nac 82 is powered by two hi-caps the connections are the same (from 82 hi-cap number one). hi-caps earlier than serial number 105469 must be connected together via the second set of sockets rather than the third as illustrated by the dotted connection cable.
  • Page 9 snaxo connection to supercap from nac 82 and supercap to nac 82 link plug removed snaxo connection to hi-cap from nac 82, 102 & 112 and hi-cap to nac 82, 102, & 112 Interconnect Cables cable 4 to 4 pin DIN direction 5 to 5 pin DIN link plug fitted...
  • Page 10 snaxo 3-6 connection to three NAP 500 power amplifiers ch1, bass, green ch1, mid, red Interconnect Cables 4 pin DIN/XLR Red 4 pin DIN/XLR Green ch2, bass, green ch2, mid, red ch1, treble, green ch2, treble, red...
  • Page 11 snaxo 3-6 connection to two NAP 500 power amplifiers ch1, bass, green ch1, treble, red Interconnect Cables 4 pin DIN/XLR Red 4 pin DIN/XLR Green ch2, bass, green ch2, treble, red...
  • Page 12 snaxo 3-6 connection to six NAP 135 power amplifiers ch1, treble, green ch2, treble, red ch1, mid, red ch2, mid, red ch1, bass, green ch2, bass, green...
  • Page 13 snaxo 2-4 connection to four NAP 135 power amplifiers ch1, treble, red ch2, treble, red Interconnect Cables 4 pin DIN/XLR Red 4 pin DIN/XLR Green ch1, bass, green ch2, bass, green...
  • Page 14 snaxo 3-6 connection to three NAP 250 power amplifiers ch1, bass ch1, mid ch2, bass ch2, mid ch1, treble ch2, treble Interconnect Cables 4 pin DIN/XLR White...

  • Page 15: Specifications

    snaxo 2-4 connection to two NAP 250 power amplifiers Interconnect Cables 4 pin DIN/XLR White ch1, bass ch1, treble ch2, bass ch2, treble Specifications snaxo input impedance >10 kilohms output impedance <50 ohms crossover frequencies 2-4 credo, sbl 2.7kHz 3-6 nbl 250Hz, 2.8kHz 3-6 dbl 350Hz, 2.8kHz...
  • Page 16 nac 112 connection to flatcap 2 and ixo 2 cover fitted ixo 2 connection to two nap 150 power amplifiers ch1 bass ch1 treble ch2 bass ch2 treble Interconnect Cables cable direction 4 to 4 pin DIN marker 5 to 5 pin DIN...
  • Page 17 Manufacturer Naim Audio Limited Southampton Road Salisbury England SP1 2LN Products snaxo 3-6, snaxo 2-4 and ixo 2 active crossovers Safety HD 195-S6 EN 60 065 Emissions Tested to EN 55013 Sound and television broadcast receivers and associated equipment Immunity Tested to EN55020...

This manual is also suitable for:

Snaxo 2-4Snaxo 3-6Ixo 2

Table of Contents