Channelview Channel Listings - Mitsubishi Electric LDTV152 - 52IN LCDtv 1920X1080 10000:1 S-vid Comp-vid USB Owner's Manual

Remote Control, continued
Net Command: The F1–F4 keys work like the A,
B, C, D buttons on some cable boxes, satellite
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C , " Programming the Remote Control ."
25. (PAUSE): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for Net Command use).
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands of the TV's remote control:
• Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
• Check HDMI devices for compatibility with the TV's
Net Command for HDMI feature (see Appendix E ).
• Perform Net Command IR "learning" for the device.
24. (RECORD): Records with a VCR or DVR.
25. (PAUSE): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26. (STOP): Stops play of a VCR, DVR, or DVD.
27. (REVERSE): Rewinds a VCR. Reverse scans a
DVR or DVD.
28. (PLAY): Plays a VCR, DVR, or DVD.
29. (FORWARD): Fast forwards a VCR. Forward scans
a DVR or DVD.
Note: To operate other audio/video devices using
the TV's remote control:
• See Appendix C , " Programming the Remote
Control ."
• For HDMI devices compatible with the TV's Net-
Command for HDMI feature, see Appendix E .
• See chapter 6, "Net Command IR Control," for
Net Command IR "Learning" of device keys.
• For use of specific keys with NetCommand-con-
trolled devices, see "Special Operation Methods,"
page 58 .
Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
1.
Press and hold POWER for several seconds until the
button blinks twice and goes off.
2.
Release the POWER button.
3.
Press keys 0 0 9 3 5 and the POWER button will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
4. TV Operation and Features
Care of the Remote Control
• Use only alkaline batteries.
• Be within 20 feet of the equipment.
• Do not press two or more buttons at the same time
unless instructed to do so.
• Do not allow unit to get wet or become heated.
• Avoid dropping on hard surfaces.
• Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
• Do not mix old and new batteries.
Low-Battery Indicator
If you press a key and the POWER key blinks five times,
replace the remote control's batteries.
Ch annelView Channel Listings
ChannelView™ displays channel names and program
information, as sent by broadcasters or your local cable
service provider, for memorized channels on ANT 1 or ANT
2. Listings may be incomplete. No program information is
displayed for analog channels. An analog channel name is
displayed only if you assigned a name in the Setup > Edit
menu ( page 45 ).
To receive ChannelView updates:
• Keep the Energy Mode set to
• Set the TV clock
• Leave the TV powered off for a while each day to
receive updates.
Notes:
- Listings are updated for the digital channel you are
currently watching.
- If the time or date displayed are incorrect, change
the TV's time, time zone, date, or Daylight Savings
Time settings in the Setup menu.
Using ChannelView
Feature
See ChannelView listings
from ANT 1 or ANT 2.
Close ChannelView
Scan channels one by one. Press and hold
Scan channels quickly.
Jump to listings for a
specific channel.
See more of the program
description (if available).
Move navigation to the
program listings.
Move navigation to the
channel listings.
Tune to the highlighted
channel.
Fast Power On
Press Key
Press GUIDE.
Press GUIDE or EXIT.
or .
Press and hold PAGE /
1. Enter the channel
number (see numbers in
upper left of screen).
2. Press ENTER.
Press INFO.
Press .
Press .
Press ENTER.
31
.