Table of Contents Regulatory Information ..............3 Description of Warning Symbols ..........4 Safety Notices ................5 Important Safety Instructions ............. 6 Preface ..................9 Warranty and Service ..............9 1. Getting Started ..............11 1.1 Package Contents ............11 1.2 Introducing the TV ............
Regulatory Information FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Description of Warning Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING CAUTION This symbol is used to alert users This symbol is used to alert users to pay attention to important to the risk of electric shocks due descriptions regarding usage, to dangerous and uninsulated maintenance (repair), and...
Safety Notices Installation Safety Notes Location Avoid allowing the TV to get prolonged exposure to sunlight or other strong sources of heat. Leave sufficient distance between the TV and the wall to provide enough space for the emission of heat. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Page 8
Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Page 9
Personal safety 1. To avoid overloading the power supply, never plug too many electrical devices into an outlet, power strip, or extension cable. 2. Dangerous high-voltage electric power components are located inside the TV. To avoid electric shock, do not disassemble the casing. 3.
The information in this manual is subject to change without notice. To the extent allowed by applicable law, Hannspree, Inc. (“Hannspree”) shall not be liable for direct, indirect, special, exemplary, incidental or consequential damages arising from any defect or omission in this manual, even if advised of the possibility of such damages in advance.
Hannspree. The TV described in this manual may include copyrighted software of Hannspree (or other third parties). Hannspree (or other third parties) preserves the exclusive rights for copyrighted software, such as the right to distribute or reproduce the copyrighted software.
Getting Started Package Contents Make sure the following components are included in the box. Please contact Hannspree Customer Service immediately if anything is missing or damaged. • • Power cord • Remote control and batteries • User’s manual • Quick start guide •...
Introducing the TV You can watch NTSC/ATSC broadcast, cable, or digital television channels, and easily connect a VCR, STB or DVD player to the standard CVBS, S-Video, component, and HDMI input ports (location of these ports depends on model). You can also use the TV as a monitor for your PC by connecting it through the VGA port.
Control Panel Description Button Function Power button. Press to turn the TV on Power or off. Press to open the input source list or Input source INPUT mark an item on the OSD menu. Menu MENU Press to open the OSD menu. Press to increase the channel number Channel select or move upward to the previous item on...
Input and Output Jacks Description Connector Function Connect to the included power cord. Power connector AC IN Connect to an external device, such as a DVD player, set-top box, or a HDMI 1 input HDMI 1 PC’s DVI/ HDMI port. Connect to an external device, such as a DVD player, a Set-Top Box, or a HDMI 2 input...
Remote Control Description Icon Function Press to turn the TV on or off. Power INPUT Press to open the input source list. Input source Use to select a channel directly. Press 0-9 to enter the program numbers (press 1 Keypad and 0 for channel 10).
Page 17
Description Icon Function Press repeatedly to set the sleep time (Sleep off, 15, 30, 45, 60, 90, or 120 SLEEP minutes). Sleep timer A Sleep Info appears on the middle of the screen to show the remaining time. Cancel the timer by pressing the button to sleep off mode.
Page 18
CAUTION • If the remote control is not used for a long period, remove the batteries and store them properly. • Handle damaged or leaking batteries carefully, and wash hands with soap if they come in contact with leaked chemical fluids. •...
Inserting the Remote Control Batteries 1 Open the battery compartment cover at the back of the remote control (A). 2 Insert the batteries paying attention to the polarity markings inside the battery compartment (B). 3 Close the battery compartment cover (C).
Setting up your TV Basic Connections 2.1.1 Power Connection 1 Connect the power cord to the AC IN input jack on the rear of the TV. 2 Insert the plug at the other end of the power cord into a power outlet. 2.1.2 Connecting an Antenna or Cable TV Connect one end of the VHF/UHF (Antenna) or CATV cable to VHF/UHF jack on...
Connecting External Devices Connect external devices such as VCRs, Set-Top-Box, DVD players, video game consoles, earphones, or a PC to the TV using the appropriate ports on the rear of the 2.2.1 Connecting External Earphones Headphones PHONE Speakers (Built-in Amplifiers) Note: •...
2.2.2 Connecting to AV Devices AUDIO AUDIO VIDEO S-Video HDMI 1 HDMI 2 Audio Cable Video Cable (Optional) (Optional) HDMI Cable Audio/ Video Cable (Optional) (Optional) HDMI L VIDEO S-VIDEO Game Console...
2.2.3 Connecting a VCR/ STB/ DVD Player Using Component Video Connect the TV to a VCR/ STB/ DVD player using the component video inputs. AUDIO Audio Cable Video Cable (Optional) (Optional) 2.2.4 Connecting a VCR/ STB/ DVD Player Using Composite Video Connect the TV to a VCR/ STB/ DVD player using the composite video input.
2.2.5 Connecting a PC using VGA Connect the TV to your PC to use it as the monitor using the VGA port as shown. 1 Connect the VGA port of the TV to the VGA output of the PC. 2 Connect the PC LINE IN port of your TV to the line out port of the PC to listen to audio from the PC.
2.2.7 Connecting HDMI HDMI (High Definition Multimedia Interface) assures that the best video signal is always sent from source to the TV. Refer to the following illustration to connect an HDMI device to the TV. HDMI 1 HDMI 2 DVD Player HDMI Cable (Optional) Note:...
Using the TV 2.3.1 Turning the TV On and Off 1 Press on the control panel or remote control. The power LED indicator on the TV changes from red to green, indicating that the TV is on. 2 Press again. The power LED changes from green to red, indicating that the TV is off.
MUTE MUTE 3 Press to eliminate sounds, and press again or press the volume buttons to restore the original volume. 2.3.6 Editing Channel Table or Favorite Channel 1 Press MENU on the control panel or remote control, then select to enter the Channel menu.
Adjusting On-Screen Display (OSD) Settings The On-Screen Display (OSD) menu system provides a quick and simple method to adjust the TV settings. The OSD menu can be accessed through the buttons either on the control panel or the remote control. Before going to details of each OSD item, you may get acquainted with the placement of the OSD system: CURRENT MENU:...
OSD Setting Menus Follow the instructions indicated on the bottom of the OSD Function Menu. Press on the control panel or arrow keys on the remote control to scroll through the menus. press INPUT/ VOL+ on the control panel or OK key on the remote control to select an item and then press MENU/ VOL- key to exit the OSD menu.
Adjusting Audio Settings Press MENU to enter the OSD Main Audio Mode Picture Menu screen. Equalizer Audio Balance Press on the remote control or Channel Auto Volume / CH on the control panel to select Recall V-CHIP Audio menu. Setup Press / OK on the remote control or INPUT/ VOL+ on the control panel to...
Adjusting Channel Settings Press MENU to enter the OSD Main Menu Antenna Picture screen. Scan Mode Audio Auto Scan Press on the remote control or Channel List Channel / CH on the control panel to select V-CHIP Channel menu. Setup Press / OK on the remote control or INPUT/ VOL+ on the control panel to enter...
Adjusting V-CHIP Settings Press MENU to enter the OSD Main Enter Password Picture Menu screen. Change Password Audio Lock Press on the remote control or Unrated Block Channel MPAA / CH on the control panel to TV Rating V-CHIP select V-CHIP menu. Can.
/ OK to activate the item. • Hannspree light can be set to Low, Medium, High and Off. Note: The items available on the OSD may vary depending on the input signal source.
Troubleshooting Situation Solution • Connect the power cord properly. • Check if the power LED is on or not. • Press on the control panel or remote control. No picture and sound. • press INPUT to cycle through connected video sources. •...
Specifications LCD Panel Size 25 inch TFT Screen Format 16:9 Panel Resolution 1920 (H) x 1080 (V) TV System ATV: NTSC DTV: ATSC HDMI Input x 2 YPbPr Input x 1 S-Video Input x1 Video System Composite Input x 1 VGA (PC) Input x 1 Tuner Input x 1 AV/S-Video: (RCA x 1) R/L in...
Ap pendix: Remote Control Guide Introduction The electronic equipment type switch buttons are used for switching the current electronic equipment type on the remote control. The remote control includes 4 electronic equipment types: DVD, AUDIO, CABLE and The remote control keypad matrix includes 4 electronic equipment type switch buttons (DVD, AUDIO, CABLE and TV).
6. During the setting process, only digit keys ‘0’ through ‘9’ are valid inputs, while other buttons are deemed invalid and do not affect the code setting. For example, inputting “02” then pressing RETURN does affect the “02” already input. 6.1.3 Searching Codes If the desired electronic equipment code for setting can not be found on the list in the...
1. Press the corresponding electronic equipment button. The indicator light will come on for 2 seconds then it goes off; after 3 seconds, the indicator light will come on again, showing that the setting mode has been entered. 2. While holding the electronic equipment button, press VOL+ twice consecutively to assign volume lock to that electronic equipment (meaning the volume buttons will only transmit code values to the assigned electronic equipment even under other electronic equipment modes).
4. During the setting process, releasing the electronic equipment button exits the setting mode immediately without changing the status prior to setting. 5. Buttons other than CH+/CH- are not functional during search. Channel buttons include CH+ and CH-. 6.1.6 Factory Setting Mode Factory setting operation procedures are as follows: 1.
Page 41
6. Default volume lock setting: Electronic VOL+, VOL- and Mute Note equipment Provided by Transmit TV code manufacturer CABLE Transmit CABLE code Unlocked AUDIO Transmit AUDIO code Unlocked Transmit DVD code Unlocked 7. Default channel lock setting: Electronic CH+ and CH- Note equipment Provided by...
6.1.7 Description There is no multi-function code setting operation under TV mode but a fixed code for the TV manufacturer. Therefore, code setting and code-searching functions are disabled under this mode; other functions such as volume lock, channel lock and code display are operable.
*Installing the LCD TV requires special skill that should only be performed by qualified service personnel. Customers should not attempt to do the work themselves. Hannspree bears no responsibility for improper mounting or mounting that results in accident or injury. You can ask...