Download Print this page

Englefield SAPPHIRE 900 x 900 Installation Instructions Manual

Shower pivot door

Advertisement

Quick Links

SHOWER | SAPPHIRE® PIVOT DOOR
900 x 900
1000 x 100
1200 x 900
1200 x 1000
1609945-A02-B
December 2024
englefield.co.nz
Page 1
1456549-A02-B
November 2020

Advertisement

loading
Need help?

Need help?

Do you have a question about the SAPPHIRE 900 x 900 and is the answer not in the manual?

Questions and answers

Summary of Contents for Englefield SAPPHIRE 900 x 900

  • Page 1 SHOWER | SAPPHIRE® PIVOT DOOR 900 x 900 1000 x 100 1200 x 900 1200 x 1000 1609945-A02-B December 2024 englefield.co.nz Page 1 1456549-A02-B November 2020...
  • Page 2: Installation Instructions

    +/- 4 mm/m. ® Please install this door onto an ENGLEFIELD Quick-Fit Low Profile shower tray only, unless installing directly onto tiled walls and floor. Care must be taken when drilling into walls and floors to avoid any hidden pipes or wires.
  • Page 3 ® Pivot Door SAPPHIRE INSTALLATION INSTRUCTIONS 1x Door 1 X Seal Pack Wall Channel 1 X Side Panel Wall Channel 1 X Door (outer glazing seal 1200 x 900 mm pre-installed) 1200 x 1000 mm 1 X Side Panel 1 X Door (900 x 900 mm) (1000 x 1000 mm) 1 X Long Drip Seal...
  • Page 4 ® INSTALLATION INSTRUCTIONS Pivot Door SAPPHIRE 1x Fixing Kits Screw washer Wall plugs for side panel Screw cap Screw washer Handle assembly Fixing screws ST4 X 30 Screw cap Screws ST4 X 10 Seal for pivot Hex Key 4 MM bracket 1609945-A02-B December 2024...
  • Page 5 ® INSTALLATION INSTRUCTIONS Pivot Door SAPPHIRE ATTENTION Due to the weight of the glass panels Englefield strongly recommends constructing double studs (as below) to fix the wall retainers to. Size DIM “A” DIM “B” 900 x 900 1000 x 1000...
  • Page 6 ® Pivot Door INSTALLATION INSTRUCTIONS SAPPHIRE Caution: Ensure tray or tiled floor is level & walls are vertical & square. Tip: Cover the waste to prevent the loss of small parts. If installing onto a tray protect the tray surface during installation. (a) Mark the locations of the wall retainers.
  • Page 7 ® Pivot Door SAPPHIRE INSTALLATION INSTRUCTIONS INSIDE Reversible Doorset INSIDE OUTSIDE 3 mm x4 per channel 10 mm 10 mm This enclosure is reversible. Select which side the door panel will be on. Note the different wall channel profiles for the door & side panel. Orient accordingly. Place the wall channels up,10 mm in from tray edge.
  • Page 8 ® Pivot Door SAPPHIRE INSTALLATION INSTRUCTIONS INSIDE OUTSIDE INSIDE OUTSIDE Reposition the channels back on the wall, aligned with fixing holes. For the door frame wall channel, place a screw washer over the fixing screw. Insert screw with washer into fixing hole and tighten. Repeat for all 4 fixing screws. Place the screw cover caps on.
  • Page 9 ® INSTALLATION INSTRUCTIONS Pivot Door SAPPHIRE JYC GLASS AS/NZS 2208 SMKB 25257 TF8 GRADE A Ensure the badge is facing outside of shower while installing onto the tray. Carefully insert the door frame fully into the wall channel, sitting on the tray sill. Carefully insert the glass side panel fully into the wall channel, sitting on the tray sill.
  • Page 10 ® SAPPHIRE Pivot Door INSTALLATION INSTRUCTIONS Keep the corner post assembly tightly fitted together and make frame adjustments by sliding the glass panels in or out inside the wall channels. Adjust until there is an even distance between frame and tray edge all around. Ensure that posts are vertical by using a level.
  • Page 11 ® Pivot Door INSTALLATION INSTRUCTIONS SAPPHIRE Ø3mm Y1 = Y2 3 mm Use a level to ensure that the frame is square. From the inside of the enclosure, drill through the corner post into the door frame. Be careful not to pierce all the way through or damage any other components. Place a screw washer over the assembly screw.
  • Page 12 ® INSTALLATION INSTRUCTIONS SAPPHIRE Pivot Door Install the bottom seal on the door, angled fin facing inward. Install the vertical door seal, long fin facing inward. The bottom of the seal should just miss the lower rail when opening and closing the door. Carefully loosen the lower pivot plate, insert the pivot seal then re-tighten the plate.
  • Page 13 ® SAPPHIRE Pivot Door INSTALLATION INSTRUCTIONS Full Height Full Height 200 mm up 200 mm up Full length between rails and tray Install the door handle. twisting clockwise to tighten. Apply sealant along the outside surfaces of the enclosure. Do not seal from inside. Allow the silicone sealant to cure for 24 hours before use.
  • Page 14: Cleaning And Maintenance Instructions

    ® INSTALLATION INSTRUCTIONS SAPPHIRE Pivot Door CLEANING AND MAINTENANCE INSTRUCTIONS Please refer to the homeowners guide and our website for cleaning instructions. SPARE PARTS - 1 (900 x 900 mm and 1000 x 1000 mm) Door Wall Pivot Door Pivot Door Handle Channel Vertical Seal...
  • Page 15: Contact And Warranty Information

    ® Pivot Door SAPPHIRE INSTALLATION INSTRUCTIONS SPARE PARTS -2 (1200 x 900 mm , 1200 x 1000 mm) Door Hinge + Pivot Door Pivot Door Handle Door Wall Pivot Block Vertical Seal Magnetic Seal Assembly Channel 1460022-0 1615913 (1200) 1460601 1615143-0 1460002-0 Glass Clip...

This manual is also suitable for:

Sapphire 1000 x 100Sapphire 1200 x 900Sapphire 1200 x 1000