Pioneer FH-P5000MP Installation Manual

FH-P5000MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Printed in Malaysia
Imprimé en Malaisie
<CZR2972-B> UC <KMINX> <03J00001>
Connecting the Units
Note:
• When an external power amp is being used with
• This unit is for vehicles with a 12-volt battery and
this system, be sure not to connect the blue/white
negative grounding. Before installing it in a recre-
lead to the amp's power terminal. Likewise, do
ational vehicle, truck or bus, check the battery
not connect the blue/white lead to the power ter-
voltage.
• To avoid shorts in the electrical system, be sure to minal of the auto-antenna. Such connection could
disconnect the ≠ battery cable before beginning cause excessive current drain and malfunction.
installation. • To avoid short-circuiting, cover the disconnected
• Refer to the owner's manual for details on lead with insulating tape. Especially, insulate the
connecting the power amp and other units, then unused speaker leads without fail. There is a pos-
make connections correctly. sibility of short-circuiting if the leads are not insu-
lated.
• Secure the wiring with cable clamps or adhesive
• To prevent incorrect connection, the input side of
tape. To protect the wiring, wrap adhesive tape
the IP-BUS connector is blue, and the output side
around them where they lie against metal parts.
is black. Connect the connectors of the same
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake colors correctly.
and seat rails. Do not route wiring in places that • This unit can not be installed in a vehicle that
get hot, such as near the heater outlet. If the insu- does not have an ACC (accessory) position on
lation of the wiring melts or gets torn, there is a the ignition switch. (Fig. 1)
danger of the wiring short-circuiting to the vehicle
body.
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
ACC position No ACC position
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• The black lead is ground. Please ground this lead
• Since a unique BPTL circuit is employed, never
separately from the ground of high-current prod-
wire so the speaker leads are directly grounded or
ucts such as power amps.
the left and right ≠ speaker leads are common.
If you ground the products together and the
• If the RCA pin jack on the unit will not be used,
ground becomes detached, there is a risk of dam-
do not remove the caps attached to the end of the
age to the products or fire.
connector.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
• Cords for this product and those for other prod-
ing fire, emitting smoke or becoming damaged.
ucts may be different colors even if they have the
• When this product's source is switched ON, a
same function. When connecting this product to
control signal is output through the blue/white
another product, refer to the supplied manuals of
lead. Connect to an external power amp's system
both products and connect cords that have the
remote control or the car's Auto-antenna relay
same function.
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
15 cm (5-7/8 in.)
This product
Antenna jack
Fuse
Jack for the Wired Remote Control
Please see the Instruction Manual
for the Wired Remote Control
(sold separately).
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
Fig. 1
keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied with power regardless of
ignition switch position.
Red
To electric terminal controlled by ignition switch (12
V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
This terminal may or With a 2 speaker system, do not connect
may not be included. anything to the speaker leads that are not
connected to speakers.
Perform these connections when using the
optional amplifier.
Subwoofer output
(SUBWOOFER OUTPUT)
Connecting cords with RCA pin
Rear output
plugs (sold separately)
(REAR OUTPUT)
Front output
(FRONT OUTPUT)
IP-BUS input
(Blue)
Multi-CD player
(sold separately)
IP-BUS cable
Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
System remote control
+ +
Front speaker
≠ ≠
White Gray
+ +
Front speaker
≠ ≠
White/black Gray/black
Left
Green Violet
+ +
Rear speaker
≠ ≠
Green/black Violet/black
+ +
Rear speaker
≠ ≠
+ +
Subwoofer
≠ ≠
<ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Front speaker
Front speaker
Right
Rear speaker
Rear speaker
Subwoofer
Fig. 2