Advertisement
CLAM
™
CONGRATULATIONS ON YOUR RECENT PURCHASE OF A CLAM
PORTABLE ICE SHELTER! THE FOLLOWING INFORMATION IS
INCLUDED IN THIS BOOKLET :
• Safety Instructions
• Parts List
• Assembly Instructions
• Tips for Use
• Maintenance and
Care Instructions
Part No. 101528
MODEL 1060 PORTABLE ICE SHELTER
Save this instruction booklet for future reference.
Item 8844
Height: 6' 6"
Length: 6'
Width: 10'
Weight: 82 lbs.
Clam Corporation, Inc.
15600 28th Avenue North
Minneapolis, MN 55447
Phone: 763-231-4120
Fax: 763-231-4121
Customer service hours:
9am – 4pm, M-F, central time
Email: customerservice@clamcorp.com
© Clam Corporation, Inc.
Advertisement
Table of Contents
Related Manuals for Clam 1060
Summary of Contents for Clam 1060
- Page 1 Item 8844 Height: 6' 6” Length: 6' Width: 10' Weight: 82 lbs. CONGRATULATIONS ON YOUR RECENT PURCHASE OF A CLAM PORTABLE ICE SHELTER! THE FOLLOWING INFORMATION IS INCLUDED IN THIS BOOKLET : • Safety Instructions • Parts List • Assembly Instructions Clam Corporation, Inc.
-
Page 2: Safety Instructions
This tent is made with flame resistant fabric reflectors to show drivers your whereabouts. which meets CPAI-84 specifications. CLAM 1060 PARTS LIST If you need replacement parts, ITEM # DESCRIPTION QTY. -
Page 3: Parts Identification
PARTS IDENTIFICATION (Parts on this page are NOT actual size.) #5 SIDE TUBE PART 101213 #16 SPREADER TUBE PART 101186 #17 DOME POLE PART 101182 #7 SPREADER TUBE PART 101220 #8 WALL TUBE PART 101224 #24 HOOP TUBE PART 101232 #9 A SUPPORT BRACE PART 101197... - Page 4 PARTS IDENTIFICATION (Parts below this box ARE shown actual size.) #29 1" WASHER #4 NYLOCK NUT #2 KEPS NUT PART 101206 PART 101163 PART 101191 #11 3/4" SCREW #30 3/4" SCREW #20 1-1/2" SCREW PART 101212 PART 101207 PART 101208 #18 CARRIAGE BOLT #27 1-3/4"...
- Page 5 CLAM 1060 EXPLODED DRAWING Page 5...
- Page 6 Attach the three velcro strips to the hoops on top of the doors. See Diagram D. 2. INSERT POLES a. From the outside of the 1060, insert the two lower spreader tubes into the four corner pockets of the tent. Adjust tubes until tent is snug, then tighten adjustment knob. Attach side tube assembly to the lower spreader pole.
- Page 7 This must remain in place at all times while your Clam is on the ice. 5. DISMANTLING YOUR CLAM a. To take your Clam 1060 down, repeat steps 1–3 in reverse order. You can leave the license holder attached, however. Secure the side assemblies using the velcro straps on the door.
-
Page 8: Assembly Diagrams
ASSEMBLY DIAGRAMS DIAGRAM A DIAGRAM B DIAGRAM C DIAGRAM D DIAGRAM E DIAGRAM F Outside View Inside View Page 8... - Page 9 ASSEMBLY DIAGRAMS DIAGRAM G DIAGRAM H DIAGRAM I DIAGRAM J DIAGRAM K Page 9...
- Page 10 ASSEMBLY DIAGRAMS DIAGRAM L DIAGRAM M DIAGRAM N Page 10...
- Page 11 THE CLAM 1060 –– FISHES BIG, PACKS SMALL. The Clam 1060 offers a large 10' x 6' fishing space. The tubular frame adds extra strength using the Clam easy Snap-up System, and the tent is made of extra strong, super tough, Ice Armor ™...
-
Page 12: Maintenance & Care Instructions
Warranty does not cover cracked windows, tent tears, broken or bent hoops due to high wind weather conditions or unattended use. Clam Corporation will replace or repair any part found defective within the one (1) year time limit. All parts must be returned to Clam Corporation, Inc. Before returning any parts, you must first call or write and acquire a return authorization.
Need help?
Do you have a question about the 1060 and is the answer not in the manual?
Questions and answers