If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product IMPORTANT: When connecting this product to accessories and/or another product, use only high-quality shielded cables. Cable/s supplied with this product MUST be used. AuviTran Audio ToolBox Instructions Manual V2.0 2/20...
The disconnect devices of the Audio ToolBox addressing this concern. AVBx7 unit are the appliance inlet of the main • Reliable Earthing - Reliable earthing of rack- AC power supply and, if connected, the mounted equipment should be maintained.
All trademarks listed in this manual are the exclusive property of their respective owners. They are respected “as is” by AuviTran. Any use of these trademarks must receive prior approval of their respective owners. For any question, please contact the trademark’s owner directly.
AxC-Card Extraction...................... 12 9 AUDIO TOOLBOX DISPLAY PANEL ..................13 Display panels information for AVBx7 & AVBx3 ..............13 Led information on display panel of AVBx7 & AVBx3 ............13 10 CONFIGURATION THROUGH AVS-MONITOR ................15 10.1 Main panel........................15 10.1.1 WCLK-IN 75 status / GPIO display status ...............15...
Note: Toolbox control is allowed if at least one card allowing control is inserted, like Dante, AVB, Madi, ASRC/ADSP or EtherSound card AuviTran Audio ToolBox is available in installation mode (Display in front and all connectors in the back) or as stage-box for live applications (Display, Network and Audio connectors in front, Power supply and GPIO on the back).
Display only AxC-Cards in slots, PSU, GPIO, BNC AVBx3/SBM+r Front face: AVBx3/SBM+r Rear face: Display and AxC-Cards in slots PSU connectors, GPIO, BNC Here is a list of available optional cards for AuviTran Audio Toolbox: AxC-DANTE AxC-AVB AxC-CN32io AxC-ES100 AxC-SWD5G...
▪ GPO when active, force 0V (GND) on the output (support 60Vmax/500mA max) AVBx7/IS+r or /SB+r: 7 slots AuviTran Audio ToolBox 2U x 19” rack Size 483 x 253x 88 mm (19” rack, 2 U height) Seven slots available for control and audio inputs/outputs Main Power Supply 100-240 VAC - 50/60 Hz - 2.3 A...
The Audio ToolBox contains 4 GPIO (General Purpose Input/Output) configurable as GPI or GPO. GPIO are available on Euroblock connectors close to the Power Inlet Connector: 1x 6-poles on AVBx3 and 2x 4-poles on AVBx7. Each connection on GPIO must be Safety Extra Low Voltage kind (SELV). GPIO on AVBx7/SB+r and AVBx7/SB+r...
+12V and Ground as shown on left diagram. REDUNDANT PSU MANAGEMENT ON AUDIO TOOLBOX All AVBx7 racks have one Main AC input and one Auxiliary AC input for redundancy. For a single AC connection, Main input must be used. Main/Aux on AVBx7/SB+r & AVBx7/SB+r Main/Aux on AVBx3/ISM+r &...
SLOT AND EXTENSION AXC-CARDS AxC-Card Insertion The cards are electrostatic sensitive; make sure you check this before touching or handling them AuviTran Audio ToolBox Instructions Manual V2.0 11/20...
AxC-Card Extraction The cards are electrostatic sensitive; make sure you check this before touching or handling them AuviTran Audio ToolBox Instructions Manual V2.0 12/20...
AUDIO TOOLBOX DISPLAY PANEL All AuviTran Audio Toolbox have a display panel used to provide quick information on the device and AxC- cards status without the need to launch any software. Display panel is available both in StageBox and Installation models. Information provided are the same but depend on of the number of slots.
Page 14
- Reset ToolBox: Press button for two seconds. Device will restart as if powered cycled. - Revert to Factory default: When AVBx3 or AVBx7 is Running (i.e. Power On for at least 30”), press button and continue pressing button until all panel LED are lighted. Both ToolBox and all slots will then revert to their factory default values.
Rack setup window will present several tabs to set/view all available parameters for ToolBox. The “Revert to Factory” button allows reverting to factory default parameters for both ToolBox and all slots. So use this AuviTran Audio ToolBox Instructions Manual V2.0...
- Panel and LED dimmer for both ToolBox and slots Temperature is also displayed here in real time. Note: GPO comes first, GPI follows. Display in AVS-Monitor is automatically adapted from the current configuration. AuviTran Audio ToolBox Instructions Manual V2.0 16/20...
Slot setup window Thanks to the Slot setup window, user is able to set, when available, each slot parameters. One tab is available for each slot and is automatically adjusted to the slot card present. AuviTran Audio ToolBox Instructions Manual V2.0 17/20...
Through this window, user can view or set ToolBox internal matrix. It works like the NetPatch page. In addition to manually set patch between sources and receivers, two functions are available: Fully erase current matrix Change matrix mode AuviTran Audio ToolBox Instructions Manual V2.0 18/20...
AVS-Monitor is used to configure the ToolBox. Once done, if no real time monitoring is necessary, you can use the AuviTran Audio ToolBox without AVS -Monitor. - Why do I have to reconfigure my AuviTran Audio ToolBox at each startup? ...
Need help?
Do you have a question about the AVBx7 and is the answer not in the manual?
Questions and answers