Download Print this page

Let's Go Aero JACK-IT PLUS Product Manual

2-bike a-frame mount carrier

Advertisement

Quick Links

Maximum Weight Rating: 40 lbs per bike, Maximum Tire Size: 2.75in,
Maximum Jack Height is 22.5in (from coupler to top of jack). Not rated for use with bike covers.
NOTICE: All Manual information is subject to change without notice. Revised editions will be
available for free download at LetsGoAero.com. Manual information is considered factual until
made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version
Copyright© 2024, Lets Go Aero, Inc., All rights reserved.
080824Rev
PRODUCT MANUAL
Installation & Safe Use Operation Highlights
Page 1 of 6
JACK-IT
2-Bike A-Frame Mount Carrier
PARTS
QTY. DESCRIPTION
A
1
POWER TOWER
B
3
3/8IN X 1.5IN HEX BOLT
C
3
3/8IN SPLIT WASHER
D
3
3/8IN WASHER
ANGLED STINGER
E
1
F
1
STRAIGHT STINGER
G
2
NOMOTION™ PIN
H
2
1/2IN SPLIT WASHER
I
2
1/2IN FLAT WASHER
J
2
RETAINER CLIP
K
1
STEM
L
2
WING
M
4
UPPER WHEEL CRADLE
N
4
LOWER WHEEL CRADLE
O
8
RUBBER STRAP
P
8
SMALL RETAINER CLIP
Q
2
WIRE LOCK
Tools Needed:
3/4" Wrench or Socket
9/16" Wrench or Socket
For More Information & Accessories,
Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions Contact Us at
877-464-2376 or 719- 630-3800
Email: Support@LetsGoAero.com
CAUTION:
This product may effect the turning radius on some
vehicles when bicycles are loaded. Always confirm
available turning radius before travel.
PLUS
®
#B00338

Advertisement

loading
Need help?

Need help?

Do you have a question about the JACK-IT PLUS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Let's Go Aero JACK-IT PLUS

  • Page 1 JACK-IT PLUS ® 2-Bike A-Frame Mount Carrier #B00338 PRODUCT MANUAL Installation & Safe Use Operation Highlights Maximum Weight Rating: 40 lbs per bike, Maximum Tire Size: 2.75in, Maximum Jack Height is 22.5in (from coupler to top of jack). Not rated for use with bike covers. PARTS QTY.
  • Page 2 STEP 1 Tools Required: 9/16” Socket or Wrench Remove the Tongue Jack from the coupler on the trailer (customer supplied). Place the tongue jack through the Power Tower and secure with three (3) 3/8in x 1.5in Hex Bolts, three (3) 3/8in Split Washers, and three (3) 3/8in Flat Washers as shown.
  • Page 3 STEP 3 NOTE: Angled Stinger [E] shown in Fg. 3. Installation is the same for theif [Fg. 3] you choose the Straight Stinger [F] (Option B) or No Stinger (Option B) in Step 2. In the same manner as Step 2, install the Stem [K] into the Stinger [E or F] using one (1) NoMotion Pin [G], one (1) Split Ring Washer [H], one (1) Flat Washer [I] and one (1) Retainer Clip [J] as shown.
  • Page 4 STEP 6 Insert two (2) Upper Wheel Cradles [M] with Rubber Straps [O] facing in opposite [Fg. 6] directions into the upper holes of the Wing [L] as shown. [Fg. 6] Secure each Upper Wheel Cradle [M] with a Small Retainer Clip [P]. STEP 7 Slide both Wings [L] onto the Stem [K] aligning the holes at the bottom of the Wing with holes on the Stem.
  • Page 5 Operation: Bicycle Mounting Hang bicycles by the tires on the Upper [Fg. 8A] Wheel Cradles [M] with the chain rings to the outside. [Fg. 8 & 8a] Adjust the Foam Bumpers located on the Wings [L] to protect the frame of the bicycle.
  • Page 6 CAUTION: CAUTION: Make sure the NoMotion Pin [G] is properly tightened The maximum load weight is 40 lbs per bicycle. and secured before transit. Make sure the bikes are DO NOT OVERLOAD. securely attached to the rack before driving. CAUTION: DO NOT exceed the weight capacity of the hitch receivers tongue weight rating.