Toro 03184 Operator's Manual
Toro 03184 Operator's Manual

Toro 03184 Operator's Manual

27-inch verticutter reelmaster 3100-d series dpa cutting unit

Advertisement

Quick Links

Register at www.Toro.com.
Original Instructions (EN)
27-inch Verticutter
Reelmaster
®
3100-D Series DPA Cutting Unit
Model No. 03184—Serial No. 315000001 and Up
Form No. 3394-465 Rev A
*3394-465* A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 03184 and is the answer not in the manual?

Questions and answers

Summary of Contents for Toro 03184

  • Page 1 Form No. 3394-465 Rev A 27-inch Verticutter Reelmaster ® 3100-D Series DPA Cutting Unit Model No. 03184—Serial No. 315000001 and Up *3394-465* A Register at www.Toro.com. Original Instructions (EN)
  • Page 2: Table Of Contents

    You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
  • Page 3: Safety

    Toro equipment, count on Toro safety device or decal is illegible or damaged, repair or genuine parts. When it comes to reliability, Toro delivers replace it before operation is commenced. Also tighten replacement parts designed to the exact engineering any loose nuts, bolts, and screws to ensure verticutter is specification of our equipment.
  • Page 4: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter Transport roller assembly Install the transport rollers. Cotter pin – No parts required Adjust the blade depth. – No parts required Adjust the rear grass shield.
  • Page 5: Inspecting The Verticutter

    Note: Determine the left and right sides of the machine from the normal operating position. Note: Whenever the verticutter has to be tipped to expose the verticutter blades, use the kick stand (supplied with Installing the Transport Rollers traction unit) (Figure Parts needed for this procedure: Transport roller assembly...
  • Page 6: Adjusting The Rear Grass Shield

    G012270 Figure 5 G012693 1. Rear grass shield 2. Pivot bolt Figure 4 1. Gauge bar 2. Adjusting bolt 2. Rotate the grass shield to the desired setting, and tighten the bolts (Figure Note: The verticutter blades must not touch the CAUTION gauge bars.
  • Page 7: Adjusting The Transport Rollers

    2. Move the scraper rods in or out to attain 0.0 to 0.03 hydraulic drive motor for each of the locations. For any of the inch (0.0 to 0.75 mm) clearance between the scraper locations requiring the motor to be mounted on the right end and roller.
  • Page 8: Product Overview

    Product Overview Operation Note: Determine the left and right sides of the machine Specifications from the normal operating position. Net weight 63 kg (140 lb) Training Period Before operating the verticutter reels, evaluate the performance of the reel at the desired setting. Operate in a clear, unused area to determine if the desired results will be achieved.
  • Page 9: Maintenance

    Maintenance Lubricating the Verticutter Each verticutter has 6 grease fittings (Figure 8) that must be lubricated weekly with #2 general-purpose, lithium-based grease. The lubrication points are the front roller (2), the rear roller (2) and the reel bearings (2). Important: Lubricating cutting units immediately after G012694 washing helps purge water out of bearings and increases bearing life.
  • Page 10: Removing The Verticutter Blades From The Shaft

    Removing the Verticutter Install Verticutter Blades Blades from the Shaft 1. Assemble a reel blade (Figure 12). 2. Assemble a large spacer. 1. Secure the end of the verticutter shaft, which has only one washer and nut, in a vise. 3.
  • Page 11 Figure 13 1. Rebuild kit (Part No. 114–5430) 6. Bearing nut 2. Rebuild tool kit (Part No. 115–0803) 7. Inner seal tool 3. Inner seal 8. Washer 4. Bearing 9. Bearing/outer seal tool 5. Outer seal...
  • Page 12 Notes:...
  • Page 13 Notes:...
  • Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
  • Page 15 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

Table of Contents