Related Manuals for DAPAudio Odin S-18A Line Array Sub V4
Summary of Contents for DAPAudio Odin S-18A Line Array Sub V4
- Page 1 MANUAL ENGLISH Odin S-18A Line Array Sub Ordercode: D3901 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Odin S-18A Line Array Sub Table of contents Warning ....................................2 Safety Instructions ................................. 2 Connection with the mains ............................4 Return Procedure ................................4 Claims ....................................4 Description of the device ..............................5 Power cable and network cable are NOT included ..................... 5 Overview .................................. -
Page 3: Warning
Odin S-18A Line Array Sub Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. - Page 4 Odin S-18A Line Array Sub Always operate the unit with the AC ground wire connected to the electrical system ground. Avoid flames and do not put close to flammable liquids or gases. Avoid ground loops! Always be sure to connect the power amps and the mixing console to the same electrical circuit to ensure the same phase! ...
-
Page 5: Connection With The Mains
Odin S-18A Line Array Sub Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE... -
Page 6: Description Of The Device
Odin S-18A Line Array Sub Description of the device Features The Odin is our new solution for all entertainers who need a professional, robust and roadproof speaker system. Owing to the efficient class-D power amplifier and the built-in DSP protection system, it is almost impossible to deform your sound in normal conditions. -
Page 7: Backside
Odin S-18A Line Array Sub Backside Fig. 02 Rigging pin 3-pin XLR audio connector LINK Connected in parallel with the XLR input (03). Use the connector to send an audio signal to another active speaker. 3-pin XLR audio connector IN Balanced XLR line level input connector. -
Page 8: Installation
Odin S-18A Line Array Sub Installation Remove all packing materials from the Odin S-18A Line Array Sub. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. -
Page 9: Set Up And Operation
Odin S-18A Line Array Sub Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode. Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 115V specification product on 230V power, or vice versa. Preset Selector 01) Turn the preset selector (06) to choose one of the 10 presets. -
Page 10: How To Make A Data Cable
Odin S-18A Line Array Sub How to Make a Data Cable A standard ETHERNET cable can be used to replace the data cable required to transmit data. Please follow the instructions below in order to create an extra net cable. Take a standard net cable (CAT-5/ 5E /6) and connect it to the RJ45 connector, as shown in the picture below (Fig. -
Page 11: Product Specifications
Odin S-18A Line Array Sub Product Specifications Odin S-18A Line Array Sub System: Active Subwoofer, Active Array Element AMP power: 1500 W Continuous Class D, 6000W Peak Speaker: 18” (450mm) CELESTION, Ferrite Magnet Subwoofer, 4“ Voice Coil, 1200W/RMS, Water Resistant Coating Frequency response (+/-3dB): 30 Hz - 120 Hz MAX SPL @ 1 m:... - Page 12 ©2021 ODIN...
Need help?
Do you have a question about the Odin S-18A Line Array Sub V4 and is the answer not in the manual?
Questions and answers