Computer Setup; System Board - HP 100eu Illustrated Parts & Service Map

Miscellaneous Parts
1 Speakers
2 Fan sink
* Mouse, USB
*Not shown

System Board

System Board Connectors and Jumpers (top of board)
XMM1 Memory socket 1
XMM2 Memory socket 3
XBT1 RTC battery socket
USB2 Front I/O connector
USB1 Media card reader connector
F_AUDIO Front panel audio connector
CLR_CMOS Clear CMOS jumper
System Board Connectors and Jumpers (bottom of board)
P7
WLAN MODULE
WEBCAMERA
Compaq 100eu AIO Illustrated Parts & Service Map
625119-001
623377-001
537750-001
SATA2 SATA hard drive
SATA1 SATA optical drive
USB Quad stacked USB connec-
tor
RJ-45 RJ-45 connector
DC-IN AC adapter connector
SATA PWR SATA power connector
P27 Power connector
Power and lighten board connector
WLAN module slot
Camera connector
POST Audible Codes
Beeps
1 short beep and 1 long beep
followed by a three second
pause
2 short beeps and 1 long
beep followed by a three
second pause
3 short beeps and 1 long
beep followed by a three
second pause

Computer Setup

Basic system information regarding system information, setup, power management, hardware,
and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is
accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence.
If the screen prompt opportunity is missed, a restart will be necessary...
Computer Setup Menu
Heading Option / Description
Main System Time
System Date
System IDs
Language
Floppy Diskette A
1st Drive
2nd Drive
System Information
Advanced CPU Type
CPU Speed
Cache RAM
Cache RAM (L2)
Primary Video
Adapter
SATA Controller
USB Ports
Onboard LAN
Onboard LAN Boot
ROM
Supervisor Password
User Password
Change Supervisor
Password
Change User Pass-
word
Onboard Audio
Power After AC Power Fail-
ure
WOL in S5
Hyper-Threading
XD (Execute Disable) Allows you to disable/enable the processor's XD feature.
Boot Boot-time Diagnostic
Screen
(Boot Device Priority)
1st Boot Device,
2nd Boot Device,
3rd Boot Device,
4th Boot Device
CD-ROM Boot Prior-
ity
HDD Boot Priority
Floppy Group Boot
Priority
Network Group Boot
Priority
Exit Exit Saving Changes
Exit Discarding
Changes
Load Setup Defaults
Discard Changes
Save Changes
625297-002
Meaning Recommended Action
Bad memory or 1. Reseat the graphics card. Power on
memory configura-
the system.
tion error.
2. Ensure DIMMs installed in correct
sockets.
3. Replace DIMMs one at a time to
isolate faulty module.
4. Replace 3rd party memory with HP
memory.
5. Replace the system board.
Graphics card ini-
1. Reseat the graphics card.
tialization failed.
2. Replace the graphics card.
3. Replace the system board.
CPU configuration 1. Reseat the processor.
error or invalid CPU
2. Replace the processor.
detected before
3. Replace the system board.
graphics card initial-
ized.
Allows you to set system time.
Allows you to set system date.
Allows you to view or change the following by pressing
Enter: Product name, serial number, UUID, SKU, Fam-
ily name (view only), Feature byte, Build ID.
Allows you to select the language.
Allows you to set to Disabled, 1.44 MB 3.5", Not
Installed.
Allow you to: Enable/disable port configuration, view
capacity, transfer mode. Also allows you to run HDD
self-test for selected channel: SMART status check,
SMART short self test, SMART extended self test.
Allows you to view installed memory, memory banks 1-
2, BIOS revision, core version, model number, product
number, build ID.
View only.
View only.
View only.
View only.
Allows you to select boot display device when more
than 2 video options are offered by system: Onboard,
PCI-E.
Allows you to disable/enable the SATA controller.
Allows you to disable/enable individual USB ports.
Allows you to disable/enable onboard LAN controller.
Disable/enable the boot ROM of the onboard LAN chip.
Allows you to view whether the supervisor password is
enabled or disabled.
Allows you to view whether the user password is
enabled or disabled. Only displays if a Supervisor pass-
word is set.
Allows you to establish, disable, or change the supervi-
sor password.
Allows you to establish, disable, or change the user pass-
word. Only displays in a Supervisor password is set. Not
displayed on models running Windows 7.
Allows you to set the onboard audio to: auto, enabled,
disabled.
Allows you to select system restart behavior after power
loss: Stay off, Power on, Auto.
Disables/enables limited Wake on LAN from S5. Note
that the computer can only wake from S5 during a nor-
mal shutdown event. Default is disabled.
Disables/enables Hyper-Threading technology.
Default is enabled.
Disable/enable POST diagnostic messages display dur-
ing boot.
Allows you to set device group boot priority: CD-ROM
group, Hard drive group, Floppy group, Network boot
group. MS-DOS drive lettering assignments maybe
apply after a non-MS-DOS operating system has started.
Specifies boot device priority within CD/DVD drives.
Specifies boot device priority within hard drives.
Specifies boot device priority within removable devices.
NOTE: This computer does not support floppy drives.
Specifies boot device priority within bootable network
devices.
Press Enter to exit saving changes.
Press Enter to exit discarding changes.
Press Enter to load setup defaults.
Press Enter to discard changes.
Press Enter to save changes.
page 2