Download Print this page
JBL EON515 Technical Manual
Hide thumbs Also See for EON515:

Advertisement

Quick Links

Technical Manual
JBL EON515/230
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• System Power Rating:
• Frequency Response:
• Frequency Range:
• LF Power Amp:
• HF Power Amp:
• Input Gain (input 3):
• Input Gain (input 1 & 2):
• Input Impedance:
• Boost EQ:
• Low Cut Filter:
• Crossover Frequency:
SYSTEM COMPONENTS:
• Cabinet:
• Baffle/Grille Assembly:
• Low Frequency
Transducer:
PACKAGE
JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
450 W continuous, 900 W peak
42 Hz – 18 kHz (± 3 dB) (EQ in "Flat"
position)
39 Hz – 20kHz (-10 dB) (EQ in "Flat"
position)
350 W continuous at driver impedance
100 W continuous at driver inpedance
Mic position: -Infinity to +40 dB
Line position: -Infinity to +4 dB (+20
dBu Max signal input)
-Infinity to +4 dB (+20) dBu Max signal
input)
64 K ohms (balanced) 32 K (unbal-
anced)
LF +3 dB Shelfing Filter @ 200 Hz
HF + 25 dB Shelfing Filter @ 4 kHz
Preset high pass @ 120 Hz
2.2 kHz
(Not for Sale)
441739-001
265F-1 380 mm (15 in) Different-
®
ial Drive
integated woofer with dual
2" voice coils
Warranty 59660
Owners Manual
364822-001
(Available on web-site
only)
Fillers (2)
364823-001
Bag
322591-001
19"x16"xc42" LG
.003 THKLDPE
CLEAR
Carton
364824-001
Cord, AC, Line
425-00000-00 120V
425-00000-01 230V
SYSTEM COMPONENTS: (CONT'D)
• DC Resistance:
• High Frequency
Transducer:
• DC Resistance:
• Input 3 connector:
• Input 1 & 2 connectors:
• Output (Loop/Mix switch):
• XLR Pin Assignments:
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 1.0Vrms Input, 20 Hz to 2 kHz
B. L.F. Aural Sweep Test:
C. H.F. Aural Sweep Test:
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions:
• Shipping Weight:
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
WIRING DIAGRAM
Driver, High Freq
2414H
(342423-002X)
- +
GRN
GRN / BLK
(SEE SCHEMATIC PAGE)
1.35 ohm ±10%
2414H 25.4 mm (1 in ) neodymium
compression driver
3.60 ohm ± 0.2%
Balanced XLR / 1/4 inch TRS combo
jack with XLR loop through
Balanced 1/4 inch TRS jack
Balanced male XLR, +20 dBu (peak)
o/p level in MIX position
Pin 2 (+), Pin 3 (-), Pin 1 (GRN)
Ch 1 input all and pots full clockwise
3.5V Input,10 Hz to 300 Hz
.75V Input, 500 Hz to 1.5 kHz
685 x 435 x 366 mm D
(27.0 x 17.3 x 14.4 in D)
32.5 lbs. (14.8 kg)
Driver, Low Freq.
265F-1
(363837-001X)
Cone Repl
C2R265-1
-
+
BLU
BLU/BLK
Amplifier Assembly
364675-001
Wire Harness
364836-001
04-09

Advertisement

loading
Need help?

Need help?

Do you have a question about the EON515 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for JBL EON515

  • Page 1 JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A. Technical Manual JBL EON515/230 SPECIFICATIONS ACOUSTIC & ELECTRICAL SPECIFICATIONS: SYSTEM COMPONENTS: (CONT’D) • System Power Rating: 450 W continuous, 900 W peak • DC Resistance: 1.35 ohm ±10% •...
  • Page 2 JBL EON515/230 SCHEMATIC ( Wire Harness) 364836-001...
  • Page 3 Silipad, EON 500 RND, PH, CLR, (363837-001X) 140325-1JBL Rubber Foot (2) Nut (4) ZINC LCS Cone Repl 364802-001 838-00800-00 C2R265-1 Silipad, EON515 IGBT M14,REG,CLR ZINC,RH 138526-1JBL Screw (8) 365626-001 Washer (4) Silipad, MRX M5 PTx25MM 848-00100-02 138525-1JBL FIL,PH,BLK,ZINC, M14,REG, CLR ZINC...
  • Page 4 Eon 515 Troubleshooting Guide E.Bird/T.Walbert 1-15-09 Secondary circuits. 1. Start by doing a thorough visual examination of the assembly for any sign of damage. This will help guide you to the trouble area. 2. Using an ohm-meter measure from TP601 (+VCC) to TP602 (Ground). It should measure over 2K and rising as it charges up the capacitors.
  • Page 5 4. Using an ohm-meter measure from TP601 (+VCC) to TP603 (-VCC). It should measure over 2K and rising as it charges up the capacitors. If this reads near 0 ohms, then check Q370, Q371, Q372 and Q373 for shorts, and replace the damaged parts. If two of these MOSFETs are shorted then replacing them is all you will need to do to the amplifier section but you will need to check the power supply for damage.
  • Page 6 Primary circuits. 1. Using an ohm-meter check Q605 and Q606 for shorts. If these devices are shorted then check R626 and R628 which should read 10ohms. Next check Q601, Q602, Q603, Q604 for shorts and opens. If any of these are damaged then you will most likely need to replace the following parts along with the ones already identified.
  • Page 7 3. Remove the 13V supply and resistor then connect a 300Vdc supply from VBULK to SMPSREF. Verify that the signal at Q606 collector is a 300V peak to peak square wave. The current draw should be less than 70ma. 4. Verify that +Vcc and –Vcc are ~ 21Vdc with 300V on Vbulk. 5.
  • Page 8 3. 230V power up failures due to a sticking relay. The dominant failure modes observed have been a blown fuse and/or damaged U603. Check for a stuck relay by looking across the contacts of K600 while unpowered for a short between 1/2VBULK and DOUBLER. These can be accessed topside by probing T601 Pin 6 (highlighted in pink and R611 Pin 2 highlighted in white).
  • Page 9 Aux 1 Balanced Input Through Select Switch Switch Up Connects 1&2, 4&5 Switch Down Connects 2&3, 5&6 Through Balanced Output JBL Professional EON 515 Analog The CGND should be connected to Earth Ground via the Power Supply I/O_MIXER June 3, 2008 CMouzakis/SPL EON 515 Analog Rev C[1].sch...
  • Page 10 JBL Professional EON 515 Analog DRIVERS_EQ June 3, 2008 CMouzakis/SPL EON 515 Analog Rev C[1].sch...
  • Page 17 140296-4 REV. 1 PWA, EON515 EON515 REVISION HISTORY E.C.N DESCRIPTION DATE INITIAL RELEASE DERIVED FROM 140296-3 REV. 1 WITH 06/06/08 TRW THE FOLLOWING CHANGES:C503 WAS OPEN,R17 WAS 3.4K, R18 WAS 5.23K, R645 WAS 49.9K, R644 WAS 499K, R600 WAS 17.8K, R614 WAS 100, C608 WAS 1000PF, R640 WAS...
  • Page 18 140296-4 REV. 1 PWA, EON515 EON515 DESCRIPTION REF. DES. CPN MAP LOC. OPEN 103418-103J1 CAP, 0.01UF 5% 100V X7R 0603 133875-1 CAP, 1UF 10% 10V X7R 0805 SMT 103418-103J1 CAP, 0.01UF 5% 100V X7R 0603 103418-103J1 CAP, 0.01UF 5% 100V X7R 0603...
  • Page 19 140296-4 REV. 1 PWA, EON515 EON515 C343 A11427-103K1 0.01UF 50V 10% X7R MLC 0603 C344 A11427-103K1 0.01UF 50V 10% X7R MLC 0603 C345 A11427-103K1 0.01UF 50V 10% X7R MLC 0603 C346 A11427-103K1 0.01UF 50V 10% X7R MLC 0603 C347 A11427-103K1 0.01UF 50V 10% X7R MLC 0603...
  • Page 20 140296-4 REV. 1 PWA, EON515 EON515 C611 131310-2 CAP,1200UF 200VDC PC MNT ELECT C612 A10434-333JD .033UF 250V 5% MTL POLY FILM C613 A10434-333JD .033UF 250V 5% MTL POLY FILM C614 134382-1 CAP, 0.047UF 5% 400V POLYESTER C615 134382-1 CAP, 0.047UF 5% 400V POLYESTER...
  • Page 21 140296-4 REV. 1 PWA, EON515 EON515 D306 136033-1 DIODE, SCHOTTKY 40V 30MA LOWC D307 136033-1 DIODE, SCHOTTKY 40V 30MA LOWC D308 136033-1 DIODE, SCHOTTKY 40V 30MA LOWC D309 136033-1 DIODE, SCHOTTKY 40V 30MA LOWC D310 C 9283-0 DIODE, MMBD4148/914 SOT-23 SMT...
  • Page 22 140296-4 REV. 1 PWA, EON515 EON515 Q367 131046-1 TRANSISTOR, KSC3265 NPN SOT-23 Q368 131047-1 TRANSISTOR, KSA1298 PNP SOT-23 Q369 131046-1 TRANSISTOR, KSC3265 NPN SOT-23 Q370 140093-1 MOSFET, P CH 60V 17A TO220 I 3* Q371 138547-1 MOSFET, N CH 60V 30A TO220...
  • Page 23 140296-4 REV. 1 PWA, EON515 EON515 R322 A11368-24910 RES, 2.49 KOHM 1/16W 1% 0603 R327 A11368-10010 RES, 1.0 KOHM 1/16W 1% 0603 R328 A11368-10030 RES, 100.0 KOHM 1/16W 1% 0603 R329 A11368-24910 RES, 2.49 KOHM 1/16W 1% 0603 R330 A11368-24910 RES, 2.49 KOHM 1/16W 1% 0603...
  • Page 24 140296-4 REV. 1 PWA, EON515 EON515 R386 A11368-10010 RES, 1.0 KOHM 1/16W 1% 0603 R401 A11368-24910 RES, 2.49 KOHM 1/16W 1% 0603 R402 A11368-82500 RES, 825 OHM 1/16W 1% 0603 R403 A11368-82500 RES, 825 OHM 1/16W 1% 0603 R404 A11368-24910 RES, 2.49 KOHM 1/16W 1% 0603...
  • Page 25 RES, 1.0 KOHM 1/16W 1% 0603 140098-1 THERMISTOR, 10K NTC 1% 0603 OPEN RT601 101103-1 PTC, 6.0 OHM 265V T601 140307-2 XFMR, EON515 MAIN T602 134525-2 XFMR, 10:12:12 GATE DRIVE TP350 127064-1 TEST POINT, SMT 1206 TP351 127064-1 TEST POINT, SMT 1206...
  • Page 26 140296-4 REV. 1 PWA, EON515 EON515 Count of CPN Total (blank) 101031-1 101103-1 102242-1 102438-470J2 103192-1 103418-103J1 125360-1 125594-1 125770-1 125798-1 125846-1 125869-1 126539-1 126549-1 126559-1 126620-1 127064-1 127075-1 130561-1 130615-1 131015-1 131046-1 131047-1 131310-2 132014-1 132559-1 133272-1 133869-1 133875-1...
  • Page 27 140296-4 REV. 1 PWA, EON515 EON515 138997-1 139278-1 140093-1 140098-1 140156-1 140262-1 140295-4 140299-1 140307-2 140427-1 140428-1 140429-1 140569-1 140570-1 A10434-104JD A10434-333JD A11368-10000 A11368-10001 A11368-10010 A11368-10020 A11368-10021 A11368-10030 A11368-10040 A11368-10041 A11368-10R00 A11368-10R01 A11368-10R03 A11368-12410 A11368-13020 A11368-13021 A11368-15020 A11368-19120 A11368-20010 A11368-20011...
  • Page 28 140296-4 REV. 1 PWA, EON515 EON515 A11368-56200 A11368-59011 A11368-68111 A11368-73211 A11368-75000 A11368-82500 A11368-84510 A11368-84R51 A11368-97610 A11369-101J1 A11369-102F2 A11369-102J1 A11369-102J2 A11369-220J1 A11369-221J1 A11369-222J2 A11369-332J5 A11369-391J1 A11369-5R6D1 A11369-680J1 A11371-0R00 A11371-0R04 A11371-1615 A11371-3923 A11371-5R11 A11371-8235 A11427-103K1 A11427-104K2 A11427-224J5 A11427-334J5 A11427-473K2 C 5094-5 C 5095-2...

This manual is also suitable for:

Eon230