Subscribe to Our Youtube Channel
Related Manuals for Dell Pro 32 Plus
Summary of Contents for Dell Pro 32 Plus
- Page 1 Dell Pro 32 Plus QHD USB-C Hub Monitor P3225DE Teardown Instruction Model: P3225DE Regulatory Model: P3225DEt February 2025 Rev. A00...
-
Page 2: Notes, Cautions, And Warnings
A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2025 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners. -
Page 3: Table Of Contents
Contacting Dell ........ -
Page 4: Safety Instructions
Safety instructions Use the following safety guidelines to protect your monitor from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your monitor. -
Page 5: Disassembly
Disassembly CAUTION: The information in this section is intended for authorized service technicians in the EMEA region. Dell prohibits users from disassembling the monitor, and any damage caused by unauthorized servicing will not be covered under the warranty. Recommended tools The procedures in this document may require the following tools: •... -
Page 6: Stand
Stand Removing the stand Prerequisites 1. Follow the procedure in Before working inside your monitor. Figure 1. Removing the stand Steps 1. Place the monitor on a soft cloth or cushion. 2. Press and hold the stand-release button. 3. Lift the stand assembly away from the monitor. 4. -
Page 7: Back Cover
Back cover Removing the back cover Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. Figure 2. Removing the back cover Steps 1. Remove four screws (M4x10) to release the back cover. 2. Using both hands, gently pry the back cover off, starting from the left and right sides, then moving to the top and bottom. 3. -
Page 8: Keypad Board
Keypad board Removing the keypad board Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. Figure 3. Removing the keypad board Steps 1. Carefully peel the double-sided tape that secures the keypad cable to the back cover. 2. -
Page 9: I/O Cover
I/O cover Removing the I/O cover Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. Figure 4. Removing the I/O cover Steps 1. Release the I/O cover from the tabs on the main chassis. 2. -
Page 10: Usb Board
USB board Removing the USB board Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. 5. Remove the cover. Figure 5. Removing the USB board Steps 1. -
Page 11: Main Chassis
Main chassis Removing the main chassis Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. 5. Remove the cover. 6. Remove the board. Figure 6. Removing the main chassis Steps 1. -
Page 12: Middle Frame
Middle frame Removing the middle frame Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. 5. Remove the cover. 6. Remove the board. 7. Remove the main chassis. -
Page 13: Main Board And Power Board
Main board and power board Removing the main board and power board Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. 5. Remove the cover. - Page 14 Figure 9. Removing the main board and the power board 4. Remove the main board and power board away from the main chassis. 5. Disconnect the two LVDS cables and connective cable from the connectors on the main board. Figure 10. Disconnecting the cables from the main board...
-
Page 15: Electrolyte Capacitors
Electrolyte capacitors Removing the Electrolyte capacitors Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the keypad board. 5. Remove the cover. 6. Remove the board. 7. Remove the main chassis. -
Page 16: Contacting Dell
Contacting Dell To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell. NOTE: Availability varies by country and product, and some services may not be available in your country. NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice, packing...
Need help?
Do you have a question about the Pro 32 Plus and is the answer not in the manual?
Questions and answers