Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Hansshow Manuals
  4. Automobile Accessories
  5. 3/Y
  6. Manual

Hansshow 3/Y Dashboard Touch Screen Swiveling Mount Kit Manual

Hide thumbs Also See for 3/Y Dashboard Touch Screen Swiveling Mount Kit:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
Model 3/Y Dashboard Touch Screen Swiveling Mount Kit Installation Instruction
Product List
Use H14 hexagon socket to adjust this screw to
adjust the rotation force of the bracket
Model 3/Y 2021+
1. Tools required for installation
Plastic pry tool, Phillips screwdriver, H5 hex wrench, H14 hex socket, 10
mm wrench
2. Installation precautions
- In order to ensure safe installation, this installation manual
highlights important notes using the following symbols.
Tip: In order to install more quickly, please read the instructions carefully.
Model 3 2017-2020
Screen Swiveling Mount
①
pry bar
②
H14 hex socket
③
10 mm wrench
④
⑤
H5 hex wrench
⑥
Phillips screwdriver
shell
⑦

Advertisement

loading
Need help?

Need help?

Do you have a question about the 3/Y Dashboard Touch Screen Swiveling Mount Kit and is the answer not in the manual?

Questions and answers

Related Manuals for Hansshow 3/Y Dashboard Touch Screen Swiveling Mount Kit

Summary of Contents for Hansshow 3/Y Dashboard Touch Screen Swiveling Mount Kit

  • Page 1 Model 3/Y Dashboard Touch Screen Swiveling Mount Kit Installation Instruction Product List Screen Swiveling Mount ⑤ H5 hex wrench ① Use H14 hexagon socket to adjust this screw to pry bar ⑥ Phillips screwdriver ② adjust the rotation force of the bracket...
  • Page 2 (If the product is +1-949 3584 793 notified of the damage after installation, claims and reissues will not be accepted, and you will need to purchase the parts again at your own expense.) Email: support@hansshow.com...
  • Page 3 Remove the original car screen 1. Remove the temperature sensor with a pry bar 2. The trim panel is a little difficult to remove, so need to pry it a few more times 3. Remove temperature sensor and rotate it...
  • Page 4 Remove the original car screen 4 . Remove the original vehicle screen with a 10mm open-ended spanner 5.Remove the two fixing screws of the original vehicle screen harness 6 .Carefully remove the screen to prevent it from hitting the screen...
  • Page 5 Remove the original car screen 7. Remove the plastic cover plate of the original vehicle with T25 box spanner 8.Press and pull out the locking clip of the connector here 9. Pad the screen with sponge first , and then put it in place to prevent the screen from sliding and damaging...
  • Page 6 Install the rotating bracket and the mesh bracket 1.Put the swivel mount kit into the original vehicle bracket hole 2. Fix the brack et w ith two screws of the original vehicle and tighten it with a 10mm spanner 3 . Place the protective cover on one side of the bracket and rotate the bracket on the other side...
  • Page 7 Install the rotating bracket and the mesh bracket 4 .the snap gasket can be installed if the gap is large. I f the gap i s small , the gasket does not need to be installed 5.Align the hole position and install the buckle at the corresponding position of the original vehicle 6 .
  • Page 8 Install the rotating bracket and the mesh bracket 7. Fix it with the original screws 8. Install the screen on the bracket 9. Fix the screen with two HS Torx screws...
  • Page 9 Install the rotating bracket and the mesh bracket 10. Fix the temperature sensor on the base M3/Y 2021+ M3 17-20 11. Sort out the harness and fix the buckle gap cover on the base...