Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Faria Manuals
  4. Measuring Instruments
  5. MG200
  6. Owner's manual

Faria MG200 Owner's Manual

Speedometer for use with smartcraft tachometer
Hide thumbs

Advertisement

Quick Links

Download this manual
Owner's Manual
MG2000 Speedometer
for use with SmartCraft™ Tachometer
IS0211
rev. E ecr#6395 08/2006

Advertisement

loading
Need help?

Need help?

Do you have a question about the MG200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Faria MG200

Summary of Contents for Faria MG200

  • Page 1 Owner’s Manual MG2000 Speedometer for use with SmartCraft™ Tachometer IS0211 rev. E ecr#6395 08/2006...
  • Page 2 4/5/05 Changes 12/21...
  • Page 3 Index Description Available Functions for display page 1 Default Screens page 1 Figure 1 page 2 Description page 2 Normal Mode page 3 Contrast and Lighting page 3 Displayed Functions page 4 Figure 2 - Select Mode page 6 Figure 3 - LCD Display Screens page 7 Fuel Functions page 8...
  • Page 4 This page left blank intentionally.
  • Page 5 14. Fuel Used 15. Trip miles 16. Steer Angle Default Screen 1 The MG2000 speedometer receives digital data via the Faria Serial Bus from the MG2000 tachometer. An analog input is provided for a sensor for air temperature. The Faria MG2000 speedometer will...
  • Page 6 “Down”, M “Mode”, and “Up”; that control the functions available. Note: The GPS data shown on the Faria® MG2000 is for reference only and The M “Mode” button is used to change is not meant to be used as a navigational the function of the LCD display and device.

  • Page 7: Normal Mode

    When the MG2000 speedometer is turned on, the unit enters “Self Test” mode. The screen will display “Self Test Faria MG2000 SW ID + Rev. PGFXXXXX Return to the “Normal” mode by pressing Date” for 12 seconds. and holding both the “Down” and “Up”...
  • Page 8 ECU. sender information. The fuel level sender Default Screen “3” should be calibrated as described in the Faria SmartCraft MG2000 tachometer manual. Speed Displays current speed in water from the installed pitot tube and/or paddle wheel as received from the MG2000 SmartCraft tachometer from the engine ECU.
  • Page 9 GPS NMEA0183 signal (if economy based on current Gal Per Hour installed and connected). and vehicle speed as received from the Note: The GPS data shown on the Faria® MG2000 SmartCraft tachometer from the MG2000™ is for reference only and is engine ECU.
  • Page 10 Displays calculated fuel used, since last reset, based on fuel rate (GPH) data received from the MG2000 SmartCraft tachometer from the engine ECU. “Fuel Used” is reset in the Faria SmartCraft MG2000 tachometer. Trip Screen “1” Displays trip miles since last reset. The Default “Trip”...

  • Page 11: Edit Mode

    Figure 3 - LCD Display Screens Normal Increase/decrease contrast Mode 40 sec. 4 sec. Auto Auto Return Return Select Use to move between screens. Mode (See Figure 2) Edit Mode Use to move between Edit Functions. 1. Select Default Screen 2.
  • Page 12 Fuel Functions Fuel Level Sender Fuel Level Sender The FUEL LEVEL SENDER provides the information displayed in the Fuel Level bar graph. This display is the equivalent of a standard fuel gauge and should be used as the reference for the fuel remaining.
  • Page 13 COG (Course Over Ground) If deviation information is not available from the connected GPS, the COG display will default to the display shown at left. This is the normal display with COG indicated as it would be displayed on a compass. If desired, True North data can be displayed by selecting it in the “set GPS COG display”...
  • Page 14 This page left blank intentionally. Page 10...
  • Page 15 Edit Mode Nominal current draw (tachometer, speedometer, and five 2” gauges The “Edit” mode is used to adjust or set with lights on maximum level): 420 the values of functions and options in the MG2000 speedometer. The following procedures specifies the steps to be taken in the “Edit”...
  • Page 16 Instructions – Function LINE Display Select Select Default Screen Default Screen Press and hold the “Up” and “Down” buttons for 2 seconds to select the “Default Screen” function. Press “Down” to select another function or “Mode” to return to “Normal” mode. Default Display (Display Screen 1 is the “Default”...
  • Page 17 Set up Organize Screen 1 Screen Press and hold the “Up” and “Down” buttons for 2 seconds to select the “Organize Screen 1” function. Press “Up” or “Down” to select another screen or “Mode” to return to “Edit” mode. Screen 1 Line 1 Function Disp.
  • Page 18 Adjust Select Adjust Clock Offset Clock Offset Press and hold the “Up” and “Down” buttons for 2 seconds to select the “Adjust Clock Offset” function. Press “Up” or “Down” to select another function or “Mode” to return to “Normal” mode. Press “Up”...
  • Page 19 Press and hold the “Up” and “Down” buttons for 2 seconds to select “Self Test” Press “Up” or “Down” to select another function. Self Test Faria MG2000 This screen will display for 10 seconds, the backlights and warning lights will flash three times.
  • Page 20 SW ID + Rev. Faria MG2000 Select Software ID and Revision” Speedometer PGFXXXXXX Date Press “Up” to select another function or “Mode” to return to “Normal” mode. Page 16...

  • Page 21: Alarm Mode

    Alarm Mode Alarm Screen (Showing both alarms) The “Alarm Screen” appears only if an alarm condition exists. The alarm condition may be a warning sent from the engine ECU or a “local” alarm such as “Low Fuel”. When an alarm condition occurs, the “Alarm Screen”...
  • Page 22 SmartCraft Harness HN0403 MG2000 Tachometer SmartCraft Tachometer Cable (To connect from the SmartCraft harness to the junction box.) 12- pin connector Pin 1 Faria Bus Pin 2 White Faria Bus Pin 3 Green Faria Bus Pin 4 Black Faria Bus...
  • Page 23 Harness HN0403 MG2000 Speedometer Speedometer Cable 12- pin connector Pin 1 Faria Bus +8.4 VDC Pin 2 White Faria Bus Pin 3 Green Faria Bus Pin 4 Black Faria Bus Ground Pin 5 Not Used Pin 6 Not Used Pin 7...
  • Page 24 SmartCraft Harness HN0407 MG2000 Tachometer SmartCraft Tachometer Cable (To connect direct to the SmartCraft junction box.) 12- pin connector Pin 1 Faria Bus +8.4 VDC Pin 2 White Faria Bus Pin 3 Green Faria Bus Pin 4 Black Faria Bus...
  • Page 25 Harness HN0407 MG2000 Speedometer Speedometer Cable 12- pin connector Pin 1 Faria Bus +8.4 VDC Pin 2 White Faria Bus Pin 3 Green Faria Bus Pin 4 Black Faria Bus Ground Pin 5 Not Used Pin 6 Not Used Pin 7...
  • Page 26 Tachometer to 2” Gauge Connection HN0503 From Tachometer 4- pin connector PJ0018 Pin A Note: To help reduce Pin B White moisture Pin C Green Pin D Black & Sheild in the gauges, be sure to install plug PJ0018 in all open connectors 2"...
  • Page 28 Copyright 2005 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the company. Faria® is the trademark of the Thomas G. Faria Corporation...