Download
Share
Print this page
Nikon NIKKOR Z 24-200mm f/4-6.3 VR Reference Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Camera Lens
  5. NIKKOR Z 24-200mm f/4-6.3 VR
  6. Reference manual
Nikon NIKKOR Z 24-200mm f/4-6.3 VR Reference Manual

Nikon NIKKOR Z 24-200mm f/4-6.3 VR Reference Manual

Hide thumbs Also See for NIKKOR Z 24-200mm f/4-6.3 VR:

Advertisement

Quick Links

Download this manual
NIKKOR Z 24-200mm f/4-6.3 VR
Reference Guide
• Read this document thoroughly before using the product.
• To ensure proper use of the product, be sure to read "For Your Safety" (page 4).
• After reading this document, keep it readily accessible for future reference.
© 2020 Nikon Corporation
SB4K01(11)
En
7MM05411-01

Advertisement

loading
Need help?

Need help?

Do you have a question about the NIKKOR Z 24-200mm f/4-6.3 VR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nikon NIKKOR Z 24-200mm f/4-6.3 VR

Summary of Contents for Nikon NIKKOR Z 24-200mm f/4-6.3 VR

  • Page 1 NIKKOR Z 24-200mm f/4-6.3 VR Reference Guide • Read this document thoroughly before using the product. • To ensure proper use of the product, be sure to read “For Your Safety” (page 4). • After reading this document, keep it readily accessible for future reference.

  • Page 2: Table Of Contents

    Table of Contents Introduction........... . . Before You Begin.

  • Page 3: Introduction

    The latest version of the camera firmware can be downloaded from the Nikon Download Center at the URL below. https://downloadcenter.nikonimglib.com/ No reproduction in any form of this document, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION.

  • Page 4: For Your Safety

    For Your Safety To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product. After reading these safety instructions, keep them readily accessible for future reference. WARNING: Failure to observe the precautions marked with this icon could result in death or severe injury.
  • Page 5  WARNING Do not directly view the sun or other bright light source through the lens. Failure to observe this precaution could result in visual impairment. Keep this product out of reach of children. Failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard.
  • Page 6  CAUTION Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens could cause fire or damage to product’s internal parts. When shooting backlit subjects, keep the sun well out of the frame. Sunlight focused into the camera when the sun is close to the frame could cause fire.

  • Page 7: Using The Lens

    Using the Lens Parts of the Lens: Names and Functions The parts of the lens are listed below. Lens hood mounting mark Use when attaching the lens hood.  “Attaching and Removing the Lens Hood” (p.14) Zoom ring Rotate to zoom in or out. Parts of the Lens: Names and Functions...
  • Page 8 Focal length scale Determine the approximate focal length when zooming the lens in or out. Focal length mark Determine the approximate focal length when zooming the lens in or out. Parts of the Lens: Names and Functions...
  • Page 9 Control ring Autofocus mode selected: In autofocus mode, rotate the ring to adjust a setting such as [Focus (M/A)] or [Aperture] assigned using the camera. For more information, see the description of [Custom control assignment]/[Custom controls (shooting)] in the camera manual. Manual focus mode selected: Rotate the ring to focus.
  • Page 10 Rubber lens-mount gasket CPU contacts Used to transfer data to and from the camera. Zoom lock switch To lock the zoom ring, zoom out to the 24 mm position and slide the switch to LOCK. This prevents the lens extending under its own weight while you are carrying the camera.
  • Page 11 Lens hood Lens hoods block stray light that would otherwise cause flare or ghosting. They also serve to protect the lens.  “Attaching and Removing the Lens Hood” (p.14) Lens hood lock mark Use when attaching the lens hood.  “Attaching and Removing the Lens Hood” (p.14) Lens hood alignment mark Use when attaching the lens hood.
  • Page 12 Lens cap (front cap) Lens cap (rear cap) Parts of the Lens: Names and Functions...

  • Page 13: Attachment And Removal

    Attachment and Removal Attaching the Lens Turn the camera off, remove the body cap, and detach the rear lens cap. Position the lens on the camera body, keeping the mounting mark on the lens aligned with the mounting mark on the camera body, and then rotate the lens counterclockwise until it clicks into place.

  • Page 14: Attaching And Removing The Lens Hood

    Attaching and Removing the Lens Hood Align the lens hood mounting mark with the lens hood alignment mark (q) and then rotate the hood (w) until the mounting mark is aligned with the lens hood lock mark (e). To remove the hood, reverse the above steps. Lens hood alignment mark Lens hood mounting mark Lens hood lock mark...

  • Page 15: Precautions For Use

    • Keep the CPU contacts clean. • Should the rubber lens-mount gasket be damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair. • Replace the lens caps when the lens is not in use.

  • Page 16: Lens Care

    Lens Care • Removing dust is normally sufficient to clean the glass surfaces of the lens. • The fluorine-coated front lens element can be cleaned as described below. Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or lens cleaning tissue;...

  • Page 17: Technical Notes

    Technical Notes Vibration Reduction (VR) The lens’s on-board vibration reduction can be enabled or disabled using camera controls; see the camera manual for details. With [Normal] selected for the on- camera vibration reduction option, vibration reduction allows speeds up to 5.0 stops * slower than would otherwise be the case, expanding the range of shutter speeds available.

  • Page 18: When The Lens Is Attached

    When the Lens Is Attached The focus position may change if you turn the camera off and then on again after focusing. If you have focused on a pre-selected location while waiting for your subject to appear, we recommend that you do not turn the camera off until the picture is taken.

  • Page 19: Using The Lens On Cameras With A Built-In Flash

    Using the Lens on Cameras with a Built-in Flash Shadows will be visible in photos where light from the built-in flash is obscured by the lens or lens hood. Remove the lens hood before shooting. Note, however, that depending on the distance to the subject and lens focal length, shadows may appear even when the lens hood is removed.

  • Page 20: Accessories

    Accessories Supplied Accessories • LC-67B Lens Cap (front cap) • LF-N1 Lens Cap (rear cap) • HB-93 Lens Hood • CL-C1 Lens Case  Using the Lens Case • The case is intended to protect the lens from scratches, not from falls or other physical shocks.

  • Page 21: Compatible Accessories

    Compatible Accessories • 67 mm screw-on filters  Filters • Use only one filter at a time. • Remove the lens hood before attaching filters or rotating circular polarizing filters. Accessories...

  • Page 22: Specifications

    Specifications Mount Nikon Z mount Focal length 24 – 200 mm Maximum aperture f/4 – 6.3 19 elements in 15 groups (including 2 ED elements, 1 aspherical ED element, 2 aspherical elements, and Lens construction elements with an ARNEO coat and a fluorine-coated front lens element) •...
  • Page 23 Approx. 76.5 mm/3.1 in. maximum Dimensions diameter × 114 mm/4.5 in. (distance from camera lens mount flange) Weight Approx. 570 g (1 lb 4.2 oz) Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice. Specifications...

  • Page 24: Notices

    Notices Notices for Customers in the U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 25 ● Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment. Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A.