Stairville Strobe-Master I Quick Start Manual

Strobe-Master I
Safety instructions
Intended use
This device is used to control electronic strobe effect devices. Any other use or use
under other operating conditions is considered to be improper and may result in per-
sonal injury or property damage. No liability will be assumed for damage resulting
from improper use.
This device may be used only by persons with sufficient physical, sensory, and intel-
lectual abilities and the necessary knowledge and experience. Other persons may use
this device only if they are supervised or instructed by a person who is responsible
for their safety.
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the device. Never allow children to play
with the packaging material and the device. Always store packaging mate-
rial out of the reach of babies and small children. Always dispose of pack-
aging material properly when it is not in use. Never allow children to use
the device without supervision. Keep small parts away from children and
make sure that the device does not shed any small parts (such as knobs)
that children could play with.
Risk of death from electrical current!
The device contains parts where high voltage is present. Never remove any
covers! There are no user-serviceable parts inside the device. Do not use
the device if covers, safety equipment or optical components are missing
or damaged.
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient condi-
tions. Only operate the device indoors within the ambient conditions spec-
ified in the "Technical specifications". Avoid operating it in environments
subject to direct sunlight, heavy pollution and strong vibrations. Avoid
operating it in environments with strong temperature fluctuations. If tem-
perature fluctuations cannot be avoided (for example after transport in
low outside temperatures), do not switch on the device immediately. Nev-
er subject the device to liquids or moisture. Never move the device to an-
other location while it is in operation. In environments with increased dirt
levels (for example due to dust, smoke, nicotine or mist): Have the device
cleaned by qualified specialists at regular intervals to prevent damage due
to overheating and other malfunctions.
Features
• Controller for all DMX and analogue strobes
• Equipped with 10 programs, blackout, single flash, full on
Quick start guide
This document contains important information on the safe use of the product.
Read and follow the safety instructions and all other instructions. Keep the docu-
ment for future reference. If you pass the product on to others, please include this
document.
Contents are subject to change. Please refer to the latest version of the documenta-
tion, which is available for download at www.thomann.de.
Damage to the external power supply due to high voltages!
The device is powered by an external power supply. The external power
supply can be damaged if it is operated with the incorrect voltage or if
high voltage peaks occur. In the worst case, excess voltages can also cause
a risk of injury and fires. Make sure that the voltage specification on the
external power supply matches the local power grid before plugging in
the power supply. Only operate the external power supply from profes-
sionally installed mains sockets that are protected by a residual current
circuit breaker (FI). Ensure that the power cord plug is easily accessible at
all times if it is the only way to safely disconnect the device from the mains
supply. As a precaution, disconnect the power supply from the power grid
when storms are approaching or if the device will not be used for a longer
period.
Damage to the device due to use of unsuitable external power supplies!
If the device is operated with an unsuitable external power supply, the
device can be damaged by overvoltage or incorrect polarity. In extreme
cases, using an unsuitable power supply can also cause a risk of injury and
fire. Only use the external power supply designated for the device or an
equivalent external power supply with identical parameters. If in doubt,
compare the voltage specifications on the external power supply and the
polarity (+/-) with the specifications in this manual and printed on the de-
vice. Voltage and polarity must always match.
Possible staining due to plasticiser in rubber feet!
The plasticiser contained in the rubber feet of this product may react with
the coating of the floor and cause permanent dark stains after some time.
If necessary, use a suitable mat or felt pads to prevent direct contact be-
tween the product's rubber feet and the floor.
General handling
• To prevent damage, never exert force while operating the device.
• Never immerse the device in water. Wipe only with a clean and dry cloth. Do not
use liquid cleaners such as benzene, thinners or flammable cleaning agents
Keep foreign substances away from the device!
Keep the device away containers with liquid. If any liquid penetrates the device,
this could destroy the device or cause a fire. Be aware that no metallic parts come
inside the device.
• Speed and brightness adjustable via fader
• Power supply adapter included
EN