Sealey SM1210 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
ELECTRICAL SAFETY.
1.1.
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs
and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that
an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products
that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested by a qualified
Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require
a fuse smaller than 13Amps for certain products (subject to 1.1.10. below) see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. Products such as welders
must not be pulled or carried by their output cables.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired
by a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked
with this symbol
1.1.10. Some products require more than a 13Amp electrical supply. In such a case, NO plug will be fitted. You must contact a qualified Electrician
to ensure a 30 amp fused supply is available. We recommend that you discuss the installation of a industrial round pin plug & socket with your Electrician.
1.2 GENERAL SAFETY
F WARNING! Disconnect the saw from the mains power before changing saw blades and accessories, servicing or performing maintenance.
! Mount the saw to a secure surface such as a work table, workbench or floor. Keep area clean and tidy and free from unrelated materials,
and ensure there is adequate lighting.
! Maintain the machine in good condition (use authorised service agent only).
! Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
! Replace table insert when worn.
! Keep the machine clean for best and safest performance and check moving parts alignment regularly.
! Before each use check saw blade and abrasive attachments for condition. If worn or damaged replace immediately.
! Place the blade guard to within 1/8" of the material being cut.
! Adjust the sanding table to within 1/16" of the disc to avoid catching the work piece or your fingers between the table and the disc.
F WARNING! Keep all safety guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
A guard or any other part that is damaged should be checked to ensure that it will operate properly and perform its intended function before
the machine is used. The safety guard is a mandatory fitting.
! Keep saw clean and sharp for best and safest performance. Follow the instructions for changing accessories.
! Use only the recommended accessories with speeds rated equal to or greater than the tool. Improper accessories can be hazardous.
! Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
! Wear approved safety eye protection, ear defenders, and if dust is generated respiratory protection.
! Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
! Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
! Keep children and unauthorised persons away from the working area.
! Secure non stable work piece with a clamp, vice or other adequate holding device.
! Avoid unintentional starting.
! Keep hands and fingers at a safe distance from the saw blade, especially at the end of a cut. Guide the work with a piece of wood or push
rod instead of your fingers when cutting small pieces.
! Disconnect the saw from the power supply before removing wood chips or dust.
! Use a support when sawing material without a flat surface to rest on.
p
F  WARNING!
It is the user’s responsibility to read, understand and comply with the following:
p
. To re-wire, connect the brown and blue wires as indicated above. DO NOT connect the brown or blue to the earth terminal.
INSTRUCTIONS FOR:
BANDSAW & SANDER
SM1210
Model No:
B l u e
N e u t r a l
B l u e
w i r e
N e u t r a l
w i r e
FUSE RATING
THIS PRODUCT MUST BE FITTED WITH A:
5 Amp FUSE
Y e l l o w & G r e e n
E a r t h w i r e
Y e l l o w & G r e e n
E a r t h w i r e
B r o w n
L i v e
B r o w n
w i r e
L i v e
w i r e
w i r e
r e s t r a i n t
w i r e
r e s t r a i n t
SM1210 -0016 - 021098