Hide thumbs Also See for XL Dual-Head:
Table of Contents

Advertisement

Quick Links

Table of Contents

......................................................................................................................
Step 8 - Silicone sock
Step 24 - Routing the cables
Step 34 - Well done!
........................................................................................
.......................................................................................
.....................................................................................................
........................................................................................................
.......................................................................
.............................................................................
.......................................................................
....................................................................................................
.......................................................................
....................................................................................
.............................................................................................
...................................................................................
......................................................................
......................................................................................
.....................................................................
.......................................................................
...................................................................................
.............................................................................
.................................................................................
.........................................................................
..................................................................................................
..............................................................................
..............................................................................
.....................................................................................
.......................................................................................
............................................................................
....................................................................
.....................................................................................
......................................................................................
......................................................................................
......................................................................................
.........................................................................
.....................................................................................
.................................................................................................
....................................................................................................
..........................................................................................
.....................................................................
..............................................................
................................................................
..........................................................
..............................................................
.....................................................
................................................
.................................................
...................................................
.........................................................
.............................................................
..................................................
.................................................................
5
6
6
7
7
8
8
9
9
10
10
11
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
21
21
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
31
32
32
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XL Dual-Head and is the answer not in the manual?

Questions and answers

Summary of Contents for Original Prusa XL Dual-Head

  • Page 1: Table Of Contents

    Table of Contents 1. Introduction ..........................................Step 1 - General information ..................Step 2 - Tools in the package ..................... Step 3 - Labels guide ......................Step 4 - Cheatsheet ............... Step 5 - Front, left, right and rear side ................
  • Page 2 ........ Step 3 - Installing the CoreXY assembly: parts preparation ..................Step 4 - CoreXY assembly ..............Step 5 - Installing the CoreXY assembly ..............Step 6 - Installing the CoreXY assembly ..................Step 7 - Securing the CoreXY ..............Step 8 - Manipulating with the printer ............
  • Page 3 ..............Step 8 - Heatbed terminals preparation ..............Step 9 - Connecting the Heatbed cables ................Step 10 - Assembling the Heatbed ..............Step 11 - Removing linear rail stoppers ................Step 12 - Installing the Heatbed ................Step 13 - Attaching the Heatbed .............
  • Page 4 Step 48 - Version B: Preparing the spool holder ........Step 49 - Version B: Mounting the spool holder assembly ....................Step 50 - Almost done! Manual changelog XL Dual-Head (Semi-Assembled) ............................. Step 1 - Version history ................Step 2 - Changes to the manual (1) ................
  • Page 5: Introduction

    1. Introduction Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 6: Step 1 General Information

    2.5mm Allen key 3.0mm Allen key Philips PH2 screwdriver The printer's package contains a lubricant, which is intended for maintenance. No need to apply it during the assembly. There is a dedicated online manual Regular printer maintenance. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 7: Step 3 Labels Guide

    The frame covers are 1:1 scale, so you can compare the size by placing the frame cover on the paper to make sure you are using the correct type. You can download it from our site prusa.io/cheatsheet-xl. Print it at 100 %, don't rescale it, otherwise, it won't work. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 8: Step 5 Front, Left, Right And Rear Side

    Keep the upper green linear stoppers in the rail. The green linear stopper will be used only during the assembly process. Once the printer is assembled, we will remove it (there is a step in the manual). Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 9: Step 7 Manipulating With The Printer

    You will be asked to install the sock later in this guide. How to install the sock - check article. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 10: Step 9 View High Resolution Images

    Lost in the instructions? Missing screw or cracked printed part? Let us know! You can contact us using following channels: Using comments under each step. Using our 24/7 live chat at shop.prusa3d.com Writing an email to info@prusa3d.com Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 11: Step 11 - Reward Yourself

    All right, eat one gummy bear. It will give you energy to start the assembly. ;) But just one! Are you ready to get started on the assembly? Let's move on to chapter 2. Base & Side frame assembly. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 12: Base & Side Frame Assembly

    2. Base & Side frame assembly Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 13: Step 1 Tools Necessary For The Next Steps

    M4x12 screw (8x) XL rear extrusion (2x) Left Z-Axis fixed (1x) Right Z-Axis rotary (1x) It is important to assemble the Z-axis parts in correct order. This guide will remind you, but keep it in mind. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 14: Step 3 Extrusion Alignment

    Take one rear extrusion prepared earlier and slide its pin into the profile insert. Mind the correct orientation of the extrusion (protrusion vs groove). There might be a slight gap between parts, we will address this in the next step. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 15: Step 5 Securing The Right Rear Extrusion

    Proceed carefully with the 3mm Allen key, avoid scratching the frame. Tighten the screws until you reach the surface of the metal plate, then stop! We will do the final tightening later on using the torque indicator. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 16: Step 7 Z-Axis Fixed Assembly

    Tighten the screws until you reach the surface of the metal plate, then stop! We will do the final tightening later on using the torque indicator. Be careful with the 3mm Allen key, you may scratch the frame. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 17: Step 9 Z-Axis Rotary Assembly

    Tighten the screws until you reach the surface of the metal plate, then stop! We will do the final tightening later on using the torque indicator. Use the longer side of the 3mm Allen key and tighten the M4x12 screws on both sides. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 18: Step 11 - Torque Indicator: Parts Preparation

    Allen key 3mm use the one already prepared STEP 12 Assembling the Torque indicator Insert the 3mm Allen key into the torque indicator. Put on the Allen key handle from the other side. The assembled torque indicator looks like this. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 19: Step 13 Final Tightening With Torque Indicator

    Haribo sweets. A high level of noise might attract nearby predators! Take one gummy bear. I said just one! Did you know that Gummy bears were first created by a German candy maker named Hans Riegel in the 1920s? Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 20: Step 15 Xlcd Parts Preparation

    STEP 15 xLCD parts preparation For the following steps, please prepare: xLCD PE cable (1x) xLCD cable (1x) M3x10 screw (2x) Frame-rear-cover (2x) Frame-corner-cable-cover (1x) Z-motor-cable-bottom-cover(2x) xLCD-cable-bottom-holder (1x) The list continues in the next step... Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 21: Step 16 Xlcd Parts Preparation

    Use the 2.5mm Allen key to tighten the M3x16 screw into the M3nEs nut in the frame. Insert the second M3x16 screw from the left side and tighten it, but not overtighten. We will adjust the correct position of the xLCD assembly later on. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 22: Step 18 Aligning The Xlcd

    Tighten the right M3x16 screw with the 2.5mm Allen key. STEP 19 xLCD assembly versions Take a look at the xLCD, there are two variants: Version A: faston on the bottom right Version B: faston on the top left Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 23: Step 20 Version A: Installing The Xlcd Pe Cable

    Take a closer look at the rear side of the xLCD assembly and locate the PE Faston on the xLCD board. Slide the PE cable connector all the way onto the PE Faston. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 24: Step 22 Xlcd Pe Cable Management

    The xLCD cable connector has a locking latch that has to face the red triangle near the xLCD connector. Connect the xLCD cable to the xLCD slot on the board. Make sure, that cable is not twisted. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 25: Step 25 - Routing The Cables

    The xLCD-cable-bottom-cover has to be in line with the horizontal frame. Don't insert the plastic cover into the horizontal frame. Insert the Extrusion cover 172mm to the frame and push it up to the xLCD-cable- bottom-cover. Fully insert the Extrusion cover 172 mm into the frame. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 26: Step 27 Horizontal Cable Inserting

    Guide the xLCD and the PE cables through the extrusion. Remove the rubber band from the cable. Insert the Z motor cable into the extrusion. Guide the cables together through the extrusion, as in the picture. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 27: Step 28 Corner Frame Cover

    Be careful, don't pinch any cables! Push the Z-motor-cable-bottom-cover into the frame. Insert the Extrusion cover 243mm. Push and slide it to the left. The extrusion cover has to be aligned with the end of the extrusion. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 28: Step 30 Preparing The Cables For Rear Cover

    Insert the Extrusion cover 243mm. Push and slide it to the right. Push the Z-motor-cable-bottom-cover into the frame. Mind the correct direction. The motor cable guide the back of the printer (not to the xLCD screen). Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 29: Step 32 Inserting Z-Motor-Cable-Bottom-Cover

    Haribo time! Eat one to five gummy bears. Did you know that the original gummy bears were inspired by the dancing bears of Europe, and Riegel named them "Gummibärchen," which means "little rubber bears" in German? Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 30 Great job! You successfully finished the base of your XL! Go to the next chapter 3. Core XY & Back assembly. The protective foam pads are back on the linear rails by accident, don't put yours back. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 31: Corexy & Back Assembly

    3. CoreXY & Back assembly Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 32: Step 1 Tools Necessary For This Chapter

    For the following steps, we need a 3mm Allen key without the torque indicator. Take the assembled torque indicator. Pull out the plastic handle. Pull out the 3mm Allen key from the torque indicator. Keep the 3D printed indicator for later use. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 33 M3x10 screw (2x) M3nEs nut (6x) STEP 4 CoreXY assembly Measure approximately 23 cm (9") from the right extrusion. Insert three M3nEs nuts into the left extrusion. Insert three M3nEs nuts into the right extrusion. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 34 Be careful while attaching the extrusions and CoreXY, avoid scratching them. First, slide the CoreXY assembly on both rear extrusions. Align the remaining profile inserts with both Z-axis extrusions. Slide the CoreXY on both Z-axis extrusions. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 35 Never manipulate the printer by using the upper metal flanges. You can damage the LED lights hidden inside. Manipulate the base using the extrusions. Rotate the base back on its feet (the Core XY is facing up). Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 36 Allen key 3mm use the one already prepared STEP 10 Assembling the Torque indicator Insert the 3mm Allen key into the torque indicator. Put on the Allen key handle from the other side. The assembled torque indicator looks like this. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 37 Repeat this procedure on all M4x12 screws inserted into the Z-axis extrusions. STEP 12 Haribo time! Take one gummy bear. Did you know that Gummy bears were initially sold as a novelty item and gained popularity in Germany before spreading to other countries? Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 38 Align its hole with the hole in the linear rail. Double check you have used the middle nut. Insert the M3x10 screw into the upper hole. Tighten the M3x10 screw with a 2.5mm Allen key. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 39 With your finger, turn the nut and align it with the extrusion. The springs on the nut should be facing down. The exact position of the nut will be adjusted later on. For now, slide it approximately to the center of the extrusion. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 40 Make sure all the connectors are facing out from the printer as in the picture. Do not tighten the screw firmly, we might need to adjust the position of the Earthing-connector in the extrusion later on. 4-5 turns are enough. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 41 Do not tighten the screw firmly, we might need to adjust the position of the Earthing-connector in the extrusion later on. 4-5 turns are enough. STEP 20 Cover-clips: parts preparation For the following steps, please prepare: Cover-clip (20x) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 42 Insert the cover-clips in places, use the pictures as reference: 6x on the left side 6x on the right side 8x on the rear side The final position of each cover-clip will be adjusted later on. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 43 Slide the cover upwards and remove it. Release and remove four M3x5rT screws on the upper cable cover. Take the entire cover off. Place both covers somewhere safe, we will put them back soon. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 44 From the inside of the printer, align the Earthing-connectors with the holes of the rear panel. If needed release the screw slightly and adjust the Earthing-connector, then tighten From the outside (rear side), insert the M3x8rT screw and secure the rear panel using a T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 45 Installing the XL rear panel Inside the printer: Line up all cover-clips with the holes in the rear panel. Outside the printer (rear side): Secure the cover-clips with eight M3x8rT screws using a T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 46 Turn the printer's rear side towards you. On the left edge, start from the bottom. Grab the PE, motor with xLCD cables and gently push them into the extrusion. Secure the cables with the Extrusion cover 354 mm. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 47 The xLCD cable connector has a locking latch that has to face the triangle near the xLCD connector. xLCD cable The purple line has to be on the upper side of an xLCD cable. The photo is incorrect, we'll update the photo soon. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 48 Left side is ready for now, let's focus on the right side. STEP 34 Rear right: cable management On the right edge, start from the bottom. Grab the motor cable and gently push it into the extrusion. Secure the cable with the Extrusion cover 354 mm. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 49 (the back of the printer is facing you) -> the antenna is connected. Please proceed to the next step. If not, continue to Installing the frame grounding Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 50 Installing the frame grounding Take a look from the top and on the rear right edge remove the grounding cover from the grounding plug on the CoreXY assembly. Connect the PE cable to the CoreXY grounding plug. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 51 The newest Wi-Fi antenna cable will be assembled later in the 5. chapter of this guide. The filament sensor cable is already connected to the xBuddy from one side. The other side is free, we'll connect it later. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 52 STEP 42 Rear electronics cover Be careful, don't pinch any cables. Gently attach the Rear-cable-management-upper on a rear side. Make sure that no cable is pinched. Secure it with four M3x5rT screws using a T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 53 Installing the extrusion covers: parts preparation For the following steps, please prepare: Extrusion cover 95 mm (4x) Extrusion cover 243 mm (2x) Extrusion cover 390 mm (2x) Extrusion cover 405 mm (1x) Extrusion cover 430 mm (1x) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 54 While inserting the extrusion cover, first insert both ends of the cover, then push it towards the center of the frame. Insert the extrusion covers (95 mm) into the extrusion on the left and right sides. Insert the extrusion cover (405 mm) into the extrusion. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 55 STEP 48 Good job! Well done! You just finished the CoreXY & Back assembly. Now, go to the next chapter 4. Heatbed & Side panels assembly. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 56 4. Heatbed & Side panels assembly Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 57 2.5mm Allen key Phillips PH2 screwdriver STEP 2 Side panels preparation For the following steps, please prepare: Side panel (2x) M3x8rT screw (20x) The side panels are symmetrical, it doesn't matter which one you use first. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 58 T10 screwdriver. You can use 1.5mm Allen key inside the openings to adjust the cover-clips alignment slightly. Tighten the top metal cover clip to the frame from the inside, using the T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 59 STEP 6 Haribo time! It's time for another gummy bear. Take it! Did you know that in 1981, the Haribo company, which was founded by Hans Riegel, introduced gummy bears to the United States? Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 60 Don't throw the parts away. You will need them later on! STEP 8 Heatbed terminals preparation Remove the four power terminal screws using the Phillips screwdriver. Keep them aside as we will need them in the next step. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 61 Phillips screwdriver. Double check you have connected the power cables correctly! STEP 10 Assembling the Heatbed Re-attach the bed-controller-case. Fix it in place by tightening the four screws using a T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 62 Pay attention to the connected cables while you are attaching the Heatbed! Using your hand, rotate the threaded rods slightly until both of the rods engage into the nut on the side of the Heatbed. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 63 STEP 14 Preparing the Z-Axis bearing housing For the following steps, please prepare: Z-Axis bearing housing (2x) Bearing (2x) M3x10 screw (4x) Slide both bearings into the Z-Axis bearing housings. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 64 Insert two M3x10 screws and tighten them using the 2.5mm Allen key. Repeat the same process for the other side too. STEP 16 Preparing the Heatbed screws For the following steps, please prepare: M3x12rT screw (4x) M3x20rT screw (2x) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 65 Locate the openings for the cable chain on the back of the heatbed frame. Attach the cable chain mount to the openings using two M3x20rT screws. Bend the cables slightly if needed. Tighten up the screws using the T10 screwdriver. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 66 STEP 20 Good job! Well done! You have just finished the Heatbed & Side panel assembly. Proceed to the next chapter: 5. Extruder & accessories assembly. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 67 5. Extruder & accessories assembly Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 68 T10 Torx key 2.5 mm Allen key 4.0 mm Allen key A cardboard box is to be used as heatbed protection during the setup. Hint: you can use the Nextruder box shipped with your printer. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 69 STEP 3 Installing the ToolChanger: parts preparation For the following steps, please prepare: Tool Changer Upper Lock (1x) Tool Changer Lower Lock (1x) Filament sensor spring A3 (4x) Push pin (4x) M3x12cT screw (4x) X-carriage-cover (1x) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 70 M3x12cT screws from the front side. Ensure the correct orientation of the part. Attach the Tool Changer Upper Lock assembly to the X-carriage from the top and secure it with two M3x12cT screws from the front side. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 71 M3x12rT screw (1x) M3nEs nut (1x) Filament sensor assembly Turn the printer around so that its left side is facing you. Insert the M3nEs nut into the vertical extrusion on the rear of the left side. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 72 Attach the filament sensor to the M3nEs nut using the M3x12rT screw and T10 screwdriver. STEP 9 Nextruder assembly: parts preparation For the Nextruder cable bundle assembly please prepare: Nextruder (2x) Cable bunde (2x) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 73 STEP 11 Nextruder cable bundle assembly Repeat this step for both tool heads: Attach the cable connector into the top of the Nextruder. Insert the semi-transparent PTFE tube into the fitting QSM-M5 on the Nextruder. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 74 We'll use the first two M3 holes in the metal profile. Place the first Nextruder on a box and guide the cables on the back side of the printer. The nextruder can move when handling the cabling. Keep watching the Nextruder! Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 75 Check that the docks are properly tightened. The dock must not move. The dock is a press fit, so the screw needs to be tightened very hard. Please watch the video in the next step for a better understanding. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 76 For the following steps, please prepare: Nozzle seal (2x) Spring 15x5 (2x) If you have a newer version of the xl-dock-cable-router that already has the nozzle seal installed, please skip to step First Nextruder docking. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 77 Insert the nozzle seal (with the spring) into the dock. Using a 2.5 mm Allen key, tighten the screw so that the head of the screw is 1 mm above the dock. Good! The first dock is ready. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 78 Push the 2.5 mm Allen key all the way through the hole in the rear metal sheet until you reach the middle screw in the xl-dock-cable-router and tighten the screw. The dock is a press fit, so the screw needs to be tightened very hard. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 79 STEP 23 Dock inspection: video The following instructions need to be done correctly and carefully. Achieve better understanding and successful assembly by watching the video alongside the guide. Watch this prusa.io/XL-dock- installation. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 80 Place the two metal inserts through the white holes in the dock. The magnets will help you dock the Nextruder. Check that the Nozzle seal lightly touches the nozzle. Well done, the second Nextruder is ready! Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 81 Version A: The Wi-fi antenna holder is on the side The antenna connector has to be assembled by you: Version B: The Wi-fi antenna is in the middle. Please skip to Version B: Connecting the Nextruder cables. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 82 Version A: Installing the Wi-Fi antenna: parts preparation For the following steps, please prepare: Wi-Fi antenna (1x) The Original Prusa XL might be shipped with one of the two versions of the Wi-Fi antenna. Each has a different shape. Both work the same.
  • Page 83 Loosen four screws securing the electronics cover. Remove the cover. Connect the second Nextruder cable to the lower slot labeled DWARF 2. Connect the first Nextruder cable to the upper slot labeled DWARF 1. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 84 The antenna connector is prepared. The latest version of the connector has a thicker washer. We don't need it anymore. You can throw it away. Insert the antenna connector into the same-shaped hole in the Wi-Fi-antenna- holder . Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 85 Attach the antenna-holder on the screws and push the cover to the left and tighten the screws. Connect the antenna cable with the antenna connector on the XL buddy board. Support the Wifi board with your finger while attaching the cable. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 86 Version B: Installing the Wi-Fi antenna: parts preparation For the following steps, please prepare: Wi-Fi antenna (1x) The Original Prusa XL is shipped with two versions of the Wi-Fi antenna, each with a different shape. The functionality is the same.
  • Page 87 To make things worse, we have a new spoolholder for you. Versions: Version A: Printed spoolholder Do you have this? Continue to the next step. Version B: Injection molded spoolholder Do you have this? Continue to the Version B: Assembling the spool holder: parts preparation. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 88 Anyway, we recommend approximately the same position as you can see in the picture. Insert the second M5nEs nut in the extrusion approximately to the same position as shown. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 89 Do not use the spool holder as a handle! Keep in mind that if you mount the Spool holder too high or too low, it may not fit the filament spool on it. There has to be enough space around it. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 90 Keep in mind that if you mount the Spool holder too high or too low, it may not fit the filament spool on it. There has to be enough space around it. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 91 Insert the M4x12 screw on the longer side of the 3mm Allen key. Insert the 3mm Allen key with the M4x12 screw through the assembled spool holder to the prepared hole in the spool-holder-base. The M4x12 screw has to protrude through the spool-holder-base. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 92 Do not use the spool holder as a handle! STEP 50 Almost done! Congratulation! Your Original Prusa XL is ready to be fired up! Compare the final look with the picture. Now, let's go to the last chapter First run. Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 93 Manual changelog XL Dual-Head (Semi-Assembled) Original Prusa XL Dual-Head (Semi-Assembled)
  • Page 94 Manual changelog XL Dual-Head (Semi-Assembled) STEP 1 Version history Versions of the Original Prusa XL semi-assembled (Dual-head) manual: 06/2023 - Initial version 1.00 07/2023 - Updated to version 1.02 08/2023 - Updated to version 1.03 11/2023 - Updated to version 1.04 05/2024 - Updated to version 1.05...
  • Page 95 Manual changelog XL Dual-Head (Semi-Assembled) STEP 3 Changes to the manual (2) 08/2023 - Antenna adapter Added instructions for the new antenna adapter. Manual version 1.02 STEP 4 Changes to the manual (3) 08/2023 - Nextruder dock Added instructions for the new dock.
  • Page 96 Manual changelog XL Dual-Head (Semi-Assembled) STEP 5 Changes to the manual (4) 11/2023 - Spoolholder Added instructions for the new injection molded Spoolholder. Manual version 1.04 STEP 6 Changes to the manual (5) 05/2024 Added information about the new gray nozzle seal.
  • Page 97 Notes:...
  • Page 99 Notes:...
  • Page 101 Notes:...
  • Page 103 Notes:...

Table of Contents