Advertisement
Menu Tree
Basic/Advanced Menu
Sub Menu
Basic Menu
RGB
Source Select
Video
Picture
S-Video
Volume
Image Options
Picture
Projector Options
Brightness
0
Information
0
Contrast
0
Color
Advanced Menu
Hue
0
Source Select
Picture
Sharpness
0
Volume
Image Options
Volume
Color Management
Items
0
Projector Options
(Toutes)
Information
Normal/Eco
Keystone
Lamp Mode
Aspect Ratio
Advanced Options
Position/Clock
Factory Default
Resolution
Video Filter
Gamma Correction
White Balance
All Data/Current Signal
Normal/Natural1/Natural2
Menu
Setup
Brightness Red/Brightness Green/Brightness Blue/
Contrast Red/Contrast Green/Contrast Blue
Menu Mode
Language
Source Index
Source Display
Input Terminal
No Input Display
Horizontal Frequency
Volume Bar
Vertical Frequency
Keystone Bar*
Sync Polarity
Menu Display Time Manual/Auto 5 sec/Auto 15 sec/Auto 45 sec
Signal Type
* This setting is optional. you need the optional presentation
Video Type
remote control (PR51KIT).
Sync Type
Interlace
Remaining Lamp Time
Orientation
Lamp Hour Meter
Projector Usage
Cinema Position
Background
Signal Select RGB
Signal Select Video/
S-Video
Auto Adjust
Auto Start
Power Management
Power Off Confirmation On/Off
Keystone Save
White Segment
NOTE: Some menu items are not available
Default Source Select
depending on the input Source.
Communication Speed 4800/9600/19200
Control Panel Key Lock Lock/Unlock
Clear Lamp Hour Meter
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Power/Status Light Messages
Condition
Standby
Cooling down
Lamp in Normal mode
Lamp in Eco mode
Retrying to turn on lamp
One minute after lamp is
turned on
Normal/Zoom/Wide Zoom/Cinema
Lamp has reached its end of
Horizontal/Vertical/Clock/Phase
life
Auto/Native
On/Off
(Normal: 1000 hours or over)
(Eco: 1500 hours or over)
Lamp life has reached its end
of life
(Normal: 1100 hours or over)
(Eco: 1600 hours or over)
Lamp cover error
Basic/Advanced
Temperature error
English/German/French/Italian/Spanish/
Swedish/Japanese
On/Off
On/Off
Fan error
On/Off
On/Off
Lamp error
Desktop Front/Ceiling Rear/Desktop
Rear/Ceiling Front
Top/Center/Bottom
Blue/Black/Logo
Auto/RGB/Component/Scart
Auto/NTSC3.58/NTSC4.43/PAL/
PAL-M/PAL-N/PAL60/SECAM
On/Off
On/Off
On/Off
On/Off
On/Off
Last/Auto/Select
Power Indicator
Status Indicator
Note
Steady orange
–
–
Blinking green
–
Blinks green for 90 seconds
Steady green
–
–
Steady green
Steady green
–
Steady green
Blinking orange
The projector retries 3 times at an inter-
val of 15 sec for max. 45 sec)
Blinking green
No light in Normal mode /
–
Steady green in Eco mode
Steady green
Steady red
Message appears on screen during 1000-
1100 hours (1500-1600 hours: Eco mode)
of lamp usage. The projector reaches its
end of life. Please replace the lamp as
soon as possible
Steady orange
Steady red
The projector is in standby mode and can-
not be turned on.
Steady orange
Blinking red (1 sec interval)
The projector is in standby mode and can-
not be turned on.
Steady orange
Blinking red (4 sec interval)
The projector is in standby mode and can-
not be turned on.
Steady orange
Blinking red (8 sec interval)
The projector is in standby mode and can-
not be turned on.
Steady orange
Blinking red (12 sec interval)
The projector is in standby mode and can-
not be turned on.
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the power cable is plugged in and that the power button on the projector cabinet
or the remote control is on.
• Ensure that the lamp cover is installed correctly. See page E-34.
• Check to see if the projector has overheated or the lamp usage exceeds 1100 hours. If
there is insufficient ventilation around the projector or if the room where you're presenting is
particularly warm, move the projector to a cooler location.
No picture
• Use the menu to select your source (Video, S-Video or RGB). See page E-27.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-27.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Factory Default in the
Adjustment Menu. See page E-29.
Image isn't square to the
• Reposition the projector to improve its angle to the screen. See page E-22.
screen
• Use the Keystone in the Adjustment Menu to correct the trapezoid distortion. See page E-
27.
Picture is blurred
• Adjust the focus. See page E-22.
• Reposition the projector to improve its angle to the screen. See page E-22.
• Ensure that the distance between the projector and screen is within the adjustment range
of the lens. See page E-14.
Image is scrolling vertically,
• Use menus or Source button on the remote control or the cabinet to select the source you
horizontally or both
want to input.
Remote control does not
• Install new batteries. See page E-13.
work
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page E-13.
Status indicator is lit or blink-
• See the Status Light messages above.
ing
Cross color in RGB mode
• If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image with the
Position/Clock in the Image Options. See page E-29 or E-32.
Advertisement
