NEC LT75Z Quick Connect Manual

LT75Z Quick Connect Guide
Connections
Step 1 Connect the supplied 15pin-15pin signal cable.
Mini D-Sub 15 pin
connector
RGB signal cable
(supplied)
Audio cable
(not supplied)
For older Macintosh computers, use a commercially
available pin adapter to connect to your Macintosh's
video port.
Step 2 Connect the supplied power cable.
B
RG
O
DE IN
S- VI
AC
O
VI DE
DI O
AU
RO L
NT
CO
PC
Step 3 Turn on the Projector.
RGB VIDEO S-VIDEO POWER
P C
C O
N T
R O
L
AUTO ADJ.
A U
D IO
MAGNIFY VOLUME
V ID
E O
S -V
ID E
NOTE: To turn off the projector, press and hold the Power "ON/STAND BY" button for a minimum of two seconds.
Step 4 Set up the Projector.
To adjust the projector's focus and zoom use the Focus ring and the Zoom ring on the lens.
PC
CON TRO
L
AUD IO
VIDE O
S-VI
DEO
RGB
A U
D I O
A U
D IO
R G
B I
V ID
E O N P
U T
S -V
ID E
O Adjusting the Tilt Foot.
R G
B
1
Power down all equipment
before making connections.
Power cable
(supplied)
1. Lift the front edge of the projector.
2. Press the Tilt button on the top of the projector to extend the Adjustable Tilt Foot.
3. Press and hold the Tilt button.
4. Lower the front edge of the projector to the desired height and release the Tilt button to lock the
Adjustable Tilt Foot.
• If the projected image does not appear square to the screen then use keystone correction for proper adjustment. See
page 27 of the supplied user's manual.
PC
CO
NT
RO
O
R
Zoom ring
Focus ring
4
2
1
L
AU DI O
VI DE
O
S- VI
DE
O
RG
B
AC
IN
To fine-adjust the height of the rear foot,
remove the spacer and rotate the rear foot
Spacer to the appropriate height.

Remote Control Features

1. Infrared Transmitter
Direct the remote control toward the remote sensor on the pro-
jector cabinet.
2. Power Button
If power is applied, you can use this button to turn your projec-
tor on and off.
NOTE: To turn off the projector, press and hold the POWER button for
a minimum of two seconds.
3. Source Buttons
Press to select a video source.
4. Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase
for an optimal picture. Some signals may not be displayed cor-
rectly, or in some cases it may take some time for a source to
switch between sources.
5. Magnify Buttons
Use the (+) or (–) button to adjust the image size up to 400%.
6. Volume Buttons
Press (+) to increase the volume and (–) to decrease it.
7. Picture Button
3 Press this button to display the Picture adjustment window.
Each time this button is pressed, the current picture adjust-
ment item will change as follows:
4 Brightness Contrast Color Hue
Unavailable items will be skipped.
8. Freeze Button
This button will freeze a picture. Press again to resume mo-
tion.
9. Mute Button
This button turns off the image and sound for a short period of
time. Press again to restore the image and sound.
10. Aspect Button
Press this button to display the Aspect Ratio select window.
Each time this button is pressed, the current aspect ratio will
change as follows:
Normal Zoom Wide Zoom Cinema
You can also select the aspect ratio by using the Select
button. If no adjustments are performed within 3 seconds, the
Aspect Ratio select window will disappear. (See also page E-
28.)
Printed in Japan
7N8P0731
Remote Control
1
2
RGB VIDEO S-VIDEO POWER
3
4
AUTO ADJ.
MAGNIFY VOLUME
5 6
7 PICTURE FREEZE MUTE ASPECT 10
8 9
MENU HELP
12
11
13
14 15
ENTER CANCEL
RD-372E
11. Menu Button
Displays the menu.
Sharpness
12. Help Button
Provides information about the current signal and the status of
the projector.
13. Select (▲▼ ) Buttons
▲▼ :
Use these buttons to select the menu of the item you
wish to adjust.
: Use these buttons to change the level of a selected
menu item.
14. Enter Button
Executes your menu selection and activates items selected
from the menu.
15. Cancel Button
Press this button to exit the menu. While you are in the adjust-
ment or setting menu, pressing this button will return to the
previous menu.
or