Download Print this page
Maytag MAH6700A Series Technical Information
Maytag MAH6700A Series Technical Information

Maytag MAH6700A Series Technical Information

27” front load washer
Hide thumbs Also See for MAH6700A Series:

Advertisement

Quick Links

27" Front Load Washer⎯Technical Information
MAH6700A*
• Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or
repair of this unit.
• Refer to Service Manual 16026186 for detailed installation, operating, testing, troubleshooting, and disassembly
instructions.
All safety information must be followed as provided in Service Manual 16026186.
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
April 2005
©2005 Maytag Services
!
CAUTION
!
WARNING
30
H o t / C o l d
W a r m / W a r m
H i g h
A . T . C .
O n
A . T . C .
W a r m / C o l d
M e d i u m
C o l d / C o l d
G e n t l e
A . T . C .
O f f
C o l d / C o l d
L o w
A u t o T e
m p C o n t r o l
W a s h / R i n s e T e m p
S p i n S p e e d
S o i l L e v e l
C h i m e
1
O p t i o n
N o r m a l
W r i n k l e
C o n t r o l
D e l i c a t e s
H a n d
W a s h
H e a v y
Q u i c k
M e d i u m
W a s h
L i g h t
S u p e r
W a s h
DC-XXXXXXXX
16026185

Advertisement

loading
Need help?

Need help?

Do you have a question about the MAH6700A Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Maytag MAH6700A Series

  • Page 1 W a s h / R i n s e T e m p S p i n S p e e d S o i l L e v e l C h i m e April 2005 DC-XXXXXXXX ©2005 Maytag Services 16026185...
  • Page 2: Troubleshooting

    1 & 2 = 11.6ohms(±7%20°C/68°F basis), Pin2 • Reduce detergent amount for that specific & 3 = 11.6 ohms (±7% 20°C/68°Fbasis) load size and soil level. Towel loads have a • Check belt. minimal amount of soil present and typically 16026185 April 2005 ©2005 Maytag Services...
  • Page 3 LO is displayed, Main Control Board and and clean the valve screens of any debris. Door Lock Switch should be checked. • Place washer into Service Mode and check for diagnostic codes 4,18 & 22.. April 2005 ©2005 Maytag Services 16026185...
  • Page 4 Low running. Water level reset Door switch is within 15 read as open and minutes, before a the door locked spin begins. switch is read as locked. 16026185 April 2005 ©2005 Maytag Services...
  • Page 5 Press Off (also Quick variety of special service tests and view diagnostic Temperature exits Service Service displays. and Soil Level Mode) Cycle Enter / Exit Service Mode To enter Service Mode press the Chime and Extra April 2005 ©2005 Maytag Services 16026185...
  • Page 6 Code position, check the water level, if over reset level, is displayed display) drain first before entering the spin function); at the beginning of a fill session; at the beginning of 16026185 April 2005 ©2005 Maytag Services...
  • Page 7 “ Whites ”and the “ Rotary Cycle Selector ” is on and off while the system is suspended or on hold. pressed, the High water level will be – – displayed: “ 0” if below level, “ 1” if above April 2005 ©2005 Maytag Services 16026185...
  • Page 8 – level. “ 1” if valve will be turned on. This output will remain Whites. Press above level. on until the “ Rotary Cycle Selector ” button is Rotary Selector 16026185 April 2005 ©2005 Maytag Services...
  • Page 9 “d”. Rotating the Cycle Selector knob in either not be turned on. The Heater output will direction will cycle through the list of codes one code April 2005 ©2005 Maytag Services 16026185...
  • Page 10 The door Door failed to Displays "LO" Go to water out of fails to unlock after "Will Not Unlock" the machine unlock 3attempts Troubleshooting until it falls Section below the overflow level. 16026185 April 2005 ©2005 Maytag Services...
  • Page 11 Replace machine Relay failure board. open when it control board. should. 19-21 Not Used Not Used Heater Relay Display "Hr". Heater relay Check signal Replace Machine failure. not sensed. Control Board. April 2005 ©2005 Maytag Services 16026185...
  • Page 12 Service Mode. A power loss during Service bus is over specified control board. Mode will cancel this mode. limit limit Voltage for Voltage for Display motor control motor control "2E".Replace Motor specified bus is under Control Board. limit specified limit 16026185 April 2005 ©2005 Maytag Services...
  • Page 13: Component Testing Procedures

    Voltage Check = DC0V or 3.75V Check Voltage at Pin #4 and #3 of CN8 Check Voltage at Pin #1 of CN5 and Pin#1,2,3,4 of Voltage Check = DC0V or 3.75V CN10 When each Valve operates = AC120V 16026185 April 2005 ©2005 Maytag Services...
  • Page 14 NOTE: For ohm checks unplug harness connector on console and test from wire insertion side of the harness connectors. Motor Normal resistance is approximately 3.0 between any 2 pins (1,2 or 3) on motor connector. CN10 16026185 April 2005 ©2005 Maytag Services...
  • Page 15: Wiring Diagram

    Wiring Diagram WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless testing requires it. April 2005 ©2005 Maytag Services 16026185...