Ocean OVF NF H 398 DX A+ Service Manual

Vertical freezer
Hide thumbs Also See for OVF NF H 398 DX A+:

Advertisement

Quick Links

VERTICAL FREEZER
SERVICE MANUAL
Model
OVF NF H 398 DX A+
Specifications are subject to possible modifications without prior notice.
Les présentes spécifications sont susceptibles d'être modifiées sans préavis.
Las especificaciones estàn sujetas a cambios sin previo aviso
Pictures are only sketches which may be different from your equipment.
Les images sont seulement de croquis qui peuvent être différentes du design de votre équipement.
Las imágenes son sólo los bosquejos que pueden ser diferentes de su equipo.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OVF NF H 398 DX A+ and is the answer not in the manual?

Questions and answers

Summary of Contents for Ocean OVF NF H 398 DX A+

  • Page 1 VERTICAL FREEZER SERVICE MANUAL Model OVF NF H 398 DX A+ Specifications are subject to possible modifications without prior notice. Les présentes spécifications sont susceptibles d'être modifiées sans préavis. Las especificaciones estàn sujetas a cambios sin previo aviso Pictures are only sketches which may be different from your equipment. Les images sont seulement de croquis qui peuvent être différentes du design de votre équipement.
  • Page 2: Table Of Contents

    Contents 1. Safety precautions and recommendations 2. Technical Specifications 2.1 General product appearance and specifications 2.2 Electrical parts and specifications 2.3 Product outside dimensions 2.4 Temperature control and adjusting 3. Product labelling and descriptions 3.1 Type label and descriptions 3.2 Serial number expansion 3.3 Product model name expansion 4.
  • Page 3 1. Safety precautions and warnings 1. Deep freezer is set for 220-240 V 50 Hz network power. Use of incompatible voltage may cause deep freezer to become inoperable or fire. 2. Do not place the deep freezer under direct sunlight or within influence area of a stove, radiator, furnace, oven, heater or infrared.
  • Page 4 Open the freezer cover only when necessary. Please make sure that the cover is sealed properly when it is not necessary. In the event of a sudden power outage unplug your product. Plug back in 20 minutes after you make sure that the mains become normal. 17.
  • Page 5: Technical Specifications

    2. Technical Specifications 2.1 General product appearance and specifications Specifications A+/ A++ MODEL NAME 10F300EN (175cm) 10F310EN (185cm) TYPE VERTICAL DEEP FREEZER 220-240/50Hz VOLTAGE GROSS VOLUME WIDTH EXTERNA DEPTH DIMENSI HEIGHT 1725 1815 (mm) 85/ 94 NET WEIGHT/WITH 78/ 86 PACKAGING GROSS (kg) R-600a / 45g...
  • Page 6: Electrical Parts And Specifications

    Electrical-Cooling Parts And Specifications SPECIFICATIONS PRODUCT MODEL 10F300EN MODEL JIAXIPERA TB1114Y GMCC PZ90H1Y COMPRESSOR STARTING TYPE RSCR RSCR OIL TYPE Mineral, 200ml Alkylbenzene, 140±10 Main winding 21.5 Ω 23.1±7%Ω Compressor winding Auxiliary winding 22.6 Ω 30.2±7%Ω STARTING MODEL TY -QZ-108-02 QPE2-C15MD3 RELAY MODEL...
  • Page 7: Starting Relay

    JIAXIPERA TB1114Y Starting Relay TY -QZ-108- 02 B50-120...
  • Page 8 Current Protection Thermic B54-105 Compressor connection Jiaxipera TB1114Y...
  • Page 9 GMCC PZ90H1Y...
  • Page 10 Main Board Pot Board...
  • Page 11 Display Board Led Board...
  • Page 12 MAIN BOARD (DGT-after 26.07.2018) POT BOARD (DGT-after 26.07.2018)
  • Page 13 DISPLAY BOARD (DGT-after 26.07.2018) Led BOARD (DGT-after 26.07.2018)
  • Page 14: Temperature Control And Adjusting

    2.3 External Dimensions of the Product Model W (mm) D (mm) H (mm) 10F300EN (175) 1725 10F300EN (185) 1815 Details are provided in the technical diagram of the product. Temperature control and adjusting 2.4. Electronic thermostat model: 2.4.1. Super Freezer Cooler –...
  • Page 15 e) -20 °C: (Position For Mechanical Indicator 2) 3 digit seven segment on the electronic indicator board is switched to ‘-20°C’ by pressing the up or down arrow button. Then the temperature is set to 20°C. f) -21 °C: 3 digit seven segment on the electronic indicator board is switched to ‘-21°C’ by pressing the up or down arrow button.
  • Page 16: Product Labelling And Descriptions

    3. Product labelling and descriptions 3.1 Type label and descriptions IT IS PRODUCED IN SİMFER KAYSERI FACILITIES IN ACCORDANCE WITH TS EN ISO 16602 AND TS 60165-2-24. PRODUCT STOCK NO: TOTAL GROSS VOLUME: 138L PRODUCTION CODE: COOLER NET VOLUME: FREEZER NET VOLUME: 134 L MODEL: FROZEN FOOD PRESERVATION CONFIGURATION:...
  • Page 17: Serial Number Expansion

    Serial number expansion Digit 1 0 0 6 8 6 1 0 0 1 0 2 0 2 1 6 0 year PU facility Packaging Configuration code Numeric serial no. mont automation automation code code Product model name expansion Digit MODEL PRODUCT TYPE...
  • Page 18: Product Installation And Removal

    Product Installation and Removal 4.1 Door Removal Part Name How to Descriptive images 1. Use a flat screwdriver to remove the plastic cover protecting the hinge. 2. Using a phillips screwdriver, remove the upper metal hinge. Remove the door. 4.2 Door handle and lock housing removal Part Name How to Descriptive images...
  • Page 19 MODEL 2 Remove the plastic side covers by pushing them forward. Remove the phillips head screw under the cover.
  • Page 20: Thermostat Removal

    4.3 Thermostat Removal 4.3.1. Electronic Thermostat CAUTION: Always remove the plug of refrigerator before replacement. Ensure that the refrigerator is unplugged from power. Part Name How to Descriptive Images Electronic Insert a part of detail under the control panel with a diameter of Thermostat 3-4 mm about 30mm and stretch Pot Control...
  • Page 21: Capacitor Removal

    Remove the control panel detached from the body from the seats on the sheet metal and take it out. Release the tabs of the electrical connectors, remove the connectors and then remove the thermostat by pulling its capillary out carefully. 4.4 Capacitor Removal *On particular models CAUTION: Always remove the plug of refrigerator before replacement.
  • Page 22: Compressor Removal

    4.5 Compressor Removal CAUTION: Always remove the plug of refrigerator before replacement. Ensure that the refrigerator is unplugged from power. Part Name How to Descriptive Images Compressor Remove the right side plastic b*Do not panel use tools such as weld, etc.
  • Page 23 on the back of the relay by hand.
  • Page 24 Relay and Thermic are separated by removing connections on relay and thermic. Condenser connecting pipe is cut at a point close to drier with a pipe cutter. Then, compressor outlet pipe is cut at a point 2-3 cm away from the welding point.
  • Page 25: Condenser Removal

    4.6 Condenser removal Part Name How to Descriptive Images Rear Wire On the condenser, is drained, detach the of which refrigerant inlet and outlet parts of the condenser from the compressor. Remove rear wire condenser from the holders with a phillips screwdriver.
  • Page 26 Remove the screw plug with a thin tool phillips screwdriver remove the screws.
  • Page 27: Power Cycle Diagram

    Remove the connector by releasing the tabs of the eva connector. Remove evap connector slot from the main board with a phillips screwdriver and remove the connector by releasing the tabs of the connector. Remove the fan motor housing using phillips screwdriver, remove the motor...
  • Page 28: Cooling Cycle Diagram

    6. Cooling cycle diagram Evaporator Kondenser Drayer Capillary Tube Heat Exchanger Compressor Outlet Line Absorption Lline...
  • Page 29: Product Failure

    7. Product Failure 7.1 Device is not working or not cooling Does Not Cool / Inadequate Cooling Is the outlet live? Check the Infrom the mains for power customer (220-240v) (220-240v) Measure the voltage at the ends Does the of the compressor. Is there compressor Is there any...
  • Page 30 Device runs loudly Correct Abnormal noise / Noisy operation Is the appliance placed on a level ground? Place the appliance on a hard and level ground Is the adjustable leg adjusted? Are the legs of the compressor loose? Check and correct the compressor mounts and securing lugs Are the legs of...
  • Page 31: Cooling System Troubleshooting

    7.3 Cooling system troubleshooting Symptom Reason Remedy • Evaporator cooling System failed due to Discharge refrigerant from the presence or formation of cooler. Replace the drier, decreases but heats humidity. vacuum and restore required amount of refrigerant. afterwards • Condenser heat is increasing •...
  • Page 32 • Condenser is cold Refrigerant leak (regional Discharge refrigerant from the • Compressor surface icing may be observed on cooler. Replace the drier, the evaporator.) System vacuum and restore required is too failed due to presence or amount of refrigerant. •...
  • Page 33: Electrical System Troubleshooting

    7.4 Electrical system troubleshooting CAUTION: Always remove the plug of refrigerator before interference. Ensure that the refrigerator is unplugged from power. 7.5 Product Error Codes a) Error Codes (Error Codes for Products with an Indicator and Electronic Board) E1: Abnormal temperature alarm Solution: For freezer mode, abnormal temperature alarm is initiated when air sensor >...
  • Page 34 Solution: E2 error is displayed if the product cannot reach the defrosting temperature of +10 degrees 3 times consecutively and if the defrost operation is ended after 6 minutes. Check the position of defrost sensor on the evaporator and the operating state of the defrost heater.
  • Page 35: Service And Dealer Test

    4 beep signals are provided at every 60 seconds (only an audible signal is provided for the mechanical board) and “E2” error code is indicated and flashes on the indicator board. E3: Air Sensor failure Solution: E3 error is issued when the ambient temperature sensor that can be seen inside the fridge is faulty. Check the sensor connector on the main board.
  • Page 36 When the appliance is de-energized, the board is out of service test mode. If the appliance is left in service test mode, after 30 minutes it is automatically out of service test mode. The mode utilized before service mode is continued. Component Component On/Off (2nd...
  • Page 37: General View

    8. Exploded Image of the Product 8.1 General View...
  • Page 38: Door Assembly

    8.2 Door Assembly 8.3 Thermostat control panel...
  • Page 39: Door Handle Assembly

    8.4 Door handle assembly...
  • Page 40 9. Spare Part Lists NF 175 Spare Parts List Part Grouped Service Material Code Material Codes Definition YUF7D-54BB-070- PU BODY PK NF. 7 DRA. 175CABINET H60-10-240-033 SCREW Ø3.9X13 YSB DRILL BIT POINTED H35-30-520-085 CONDENSER (UF7D) YUF00-7000-054-018 CONDENSER HOLDER PLS. H35-30-360-024 THERMOSTAT FOSHAN KPF35V4-E/EXPROOF YUF02-70BB-054- CONTROL PANEL BODY...
  • Page 41 YUF7D-70BB-054- DRAWER BODY SMALL 60 CM YC200-2600-901- YUF7D-7000-054-004 DRAWER COVER STANDARD 60 CM YC200-2600-901- YUF7D-7000-054-003 DRAWER COVER BIG BOX 60 CM H60-10-240-032 Ø3.9X13 YHB SHARP POINTED FLAP SCREW YUF7D-70BB-054- FREEZER TRAY 60 CM...
  • Page 42 YUF00-70BB-054- FREEZER YUF00-5100-010-011 HANDLE REINFORCEMENT UF YUF00-5100-010-003 BOTTOM HINGE STOPPER H60-10-220-012 SCREW Ø3,5X22 YSB SHARP POINTED STAINLESS H70-10-200-009 SLOT-IN GASKET VERTICAL 7C YUF00-7000-054-004 DOOR HANDLE BOTTOM STOPPER PLS. YUF00-5100-010-004 DOOR HANDLE INSERT YUF00-7000-054-021 DOOR HANDLE TOP STOPPER PLS. H25-25-140-012 DOOR HANDLE PROFILE (330 MM) YUF00-7000-054-003 DOOR BOTTOM LEFT/RIGHT MAGNET PIN BEARING YUF02-7000-054-004 FLAP MECHANISM PLS.
  • Page 43 YUF02-7000-054-007 FLAP SCREW REINFORCEMENT YUF02-70BB-054- BOARD BOX COVER YUF02-7000-054-018 SENSOR BOX YUF02-7000-054-019 SENSOR COVER YUF02-7000-054-009 CONNECTOR SLOT REAR COVER...
  • Page 44 YUF02-7000-054-016 EVA UPPER COVER YUF02-70BB-054- BOARD BOX YUF02-7000-054-023 GAS LEAK INSPECTION PLUG YUF02-7000-054-022 DISPLAY ILLUMINATION GLASS YUF02-7000-054-021 EVAPORATION BOWL YUF02-7000-054-020 LED BOARD COVER H35-30-420-021 TOUCH CONTROL BOARD NF H35-30-500-008 POT BOARD UF NF H35-30-500-007 LED BOARD UF NF NF 185 Spare Parts List Part Material Code Grouped Service...
  • Page 45 H25-30-320-012 COMP. WHEEL PIN H60-10-140-038 SCREW M5X18 HEXAGON FLANGE YC200-2600-901- YUF7D-22BB-015- PU DOOR GR 7 DRAWER YUF00-7000-054- DOOR HANDLE STOPPER YUF00-7000-054- DOOR SIDE STOPPER H60-10-120-025 SCREW M4X12 YHB STAINLESS H15-50-000-013 GLASS SHELF 60 CM LARGE UF7D H15-50-000-014 GLASS SHELF 60 CM SMALL UF7D YC200-2600-901- YUF6D-3100-044- DRAWER COVER 54 CM 195 MM...
  • Page 46 YC200-2600-901- YUF5D-3100-044- DRAWER COVER 54 CM 246 MM YUF6D-70BB-054- DRAWER BODY SMALL 54 CM 195 MM YUF6D-70BB-054- DRAWER BODY SMALL 54 CM 195 MM YUF5D-70BB-054- DRAWER BODY SMALL 54 CM 246 MM H60-10-240-032 Ø3.9X13 YHB SHARP POINTED FLAP SCREW YUF7D-70BB-054- FREEZER TRAY 60 CM YUF00-70BB-054- FREEZER...
  • Page 47 YUF02-7000-054- FAN VIBRATION DAMPENING SILICONE FRONT-REAR YUF02-7000-054- FAN VIBRATION DAMPENING SILICONE YUF02-7000-054- FAN PROPELLER FAN MOTOR YUF02-70BB-054- EVA COVER PLUG YUF02-7000-054- EVA HOLDER YUF02-7000-054- CONNECTOR SLOT CONNECTOR SLOT FRONT COVER YUF02-7000-054- YUF02-7000-054- FLAP SCREW REINFORCEMENT YUF02-70BB-054- BOARD BOX COVER YUF02-7000-054- SENSOR BOX...
  • Page 48: Smart Coding

    YUF02-7000-054- SENSOR COVER YUF02-7000-054- CONNECTOR SLOT REAR COVER YUF02-70BB-054- BOARD BOX YUF02-7000-054- GAS LEAK INSPECTION PLUG YUF02-7000-054- DISPLAY ILLUMINATION GLASS YUF02-7000-054- EVAPORATION BOWL YUF02-7000-054- LED BOARD COVER YC200-2600-901- EVA LOWER COVER ASSEMBLY 185 EVA COVER UPPER YUF03-70BB-054- LOWER EVA COVER FRONT 185 YUF03-70BB-054- LOWER EVA COVER REAR 185 YUF02-7000-054-...
  • Page 49 FS 7406 NF A+ D S No Frost 7 Drawers Silver Avai labl FS 8401 NF A+ No Frost 8 Drawers White Opt. FS 8402 NF A+ D No Frost 8 Drawers White FS 8403 NF A+ INX No Frost 8 Drawers Inox FS 8403 NF A+ D INX...
  • Page 50 Sede Legale: via Leone XIII n°14 – 20145 Milano ITALY Cap. Soc. Euro 2.500.000,00 – Società con Socio Unico R.E.A. Milano 1544616 Cod. Fisc. – Part. IVA e n° Registro Imprese: 12287310150 www.ocean.it For product improvement, specifications and appearance in this manual are subject to change without prior notice.

This manual is also suitable for:

10f300en10f310en

Table of Contents