Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0783
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Tools Needed:
(1) Phillips-head Screwdriver
Important to Know:
1. This fixture requires a 120 VAC, 60 Hz power source.
2. For general safety and to avoid any possible damage
to the sensor, be sure the power is switched "off"
before adjustment.
3. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
4. Photocell keeps the light OFF during daylight hours.
Maximum Wattage: 35 W
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the mounting bracket.
Mounting Bracket
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
(2) 1/8" Flat-head Screwdriver
4°F ~ 113°F
Controls
Mounting Bracket Screw
1. Phillips-head screwdriver for attaching mounting screws to
mounting strap, mounting bracket and fixture to mounting bracket.
2. 1/8" wide flat-head screwdriver for connecting the source wires
into the wiring terminal station on the mounting bracket.
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
in low-level brightness when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to keep the light ON full brightness during the night.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the
controls face down.
Page 1 / 7
Fixture Mounting Screw
Wire Connector
Controls
Controls
240905
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vaxcel T0783
Summary of Contents for Vaxcel T0783
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0783 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 Light Fixture Mounting Bracket Mounting Bracket Screw FRONT Outlet Box Mounting Strap Light Head Wire Connector Backplate Silicone Fixture Mounting Screw Sensor Head Fig.1 Fig.2 Fig.3 Backup Battery 1. Before installing, please ensure the backup battery is working and can turn the light on by press the switch on the light fixture.(See Fig.1) 2.
- Page 3 Adjusting the Sensor Head: 1. Aim sensor head toward desired detection area, maintaining a 5° - 40° downward angle to allow moisture to drain. Note: Make sure sensor head is positioned with controls facing toward the ground. 2. You can rotate the sensor head up and down to change the coverage area.
- Page 4 ASSEMBLY INSTRUCTIONS (continued) FUNCTION AND OPERATION (continued) ASSEMBLY INSTRUCTIONS (continued) ASSEMBLY INSTRUCTIONS (conti FUNCTION AND OPERATION (continued): 2. AUTO MODE (nighttime operation only) ● To shift to “AUTO” mode, slide the Time Delay switch to the desired time setting (1min, 2min,3 min). At dusk, the light turns on to pre-selected low level brightness.
-
Page 5: Troubleshooting
FUNCTION AND OPERATION (continued): Customization Options Shut-off Delay ● The shut-off delay is the length of time the light will stay at full brightness after motion is detected. ● You can set the shut-off delay time: "1min", "2min", "3min". Notes: 1. - Page 6 Troubleshooting (Continued): Problem Possible Cause Solution The light turns off too late in Relocate the light fixture setting. The light fixture may be installed in a the PC setting. relatively dark location. The motion sensor may be picking up Decrease the "SENSITIVITY" setting The light stays on continuously.
-
Page 7: Spare Parts List
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
Need help?
Do you have a question about the T0783 and is the answer not in the manual?
Questions and answers