Solar charge controller can be used for charging the lead acid battery (3 pages)
Summary of Contents for ECO-WORTHY ECO-BM100V3
Page 1
Version: 1.0 BATTERY MONITOR Model:ECO-BM100V3 User Manual SUPPORT you are experiencing technical problems and cannot find a solution in this manual,please contact ECO-WORTHY for further assistance. ·Call:1-866 939 8222(US) +44 20 7570 0328(UK) +49 693 1090 113(DE) ·Email: customer.service@eco-worthy.com...
Contents ........1 Safety Precautions ........2 General Information ..........3 Specifications ...........4 What’s In The Box ...........5 Product Overview ...........6 Installation ..........13 How To Use ...........21 Troubleshooting ...........22 Appendix...
Safety Precautions · Thank you so much for choosing our products. Please read this manual carefully before using this product as it includes important information and advice on installation, use, troubleshooting, etc. Accidental damage, unauthorized repair, improper storage and use will cause failure of warranty coverage. ·...
General Information This Monitor is designed for 9-80V lithium and lead-acid batteries. It includes a high precision Hall Sensor and 3.5in touchable screen with clean and brief designed UI. With the Monitor you can check and set up the electric current, voltage, SOC, SOH, capacity and cycles of your battery.
What’s In The Box Item# Name Quantity Note Monitor Hall Sensor 5m Power Cable 2-pin 5m Hall Sensor Cable 4-pin Base Self Drilling Screw M3.9*19mm Pan Head Cross Screw M4*10mm Manual Groove Installation Aid Drawing...
Product Overview Fig. 1 Product Overview Item# Name Description Touch Screen Display info and status of the system Long press the button to turn on or Power Button turn off the Monitor. Short press to wake up or close the screen Power Indicator Indicates on/off Screw Cap...
Installation Lead the positive ends of the battery’s input and output cables through the Hall Sensor. The system can be installed as one of the following 2 modes: 1.Single Hall Sensor 1.1 Definition Only one single Hall Sensor is connected to detect the battery current.
Page 9
2. Dual Hall Sensors 2.1 Definition Two Hall Sensors are connected and the input and output cables of the battery are respectively lead through the Hall Sensors. (only 1*Hall Sensor is included. If you need to use dual Hall Sen- sors, buy another one individually) In this way the battery input and output current can be monitored at the same time, but please note the 2 Hall Sensors can not be used for reading the same...
Page 10
3. Connect the Monitor with Hall Sensor 3.1 Single Hall Sensor Connect the Hall Sensor to one of the port(Hall 1/Hall 2) on the Monitor with 5m Hall Sensor Cable. Fig.4 Connect the Monitor with Single Hall Sensor 3.2 Dual Hall Sensors Connect each Hall Sensor to either one of the port on the Moni- tor with 5m Hall Sensor Cable.
Page 11
4. Get Power Supply Hook up the 5m Power Cable on the battery (DO NOT reverse the 2 terminals), and plug the other end in the DC IN port on the Monitor. Fig.6 Connect the Battery to Monitor When installation is finished, the whole system should look as follows: Fig.7 Monitor System Wiring with Single Hall Sensor...
Page 12
Fig.8 Monitor System Wiring with Dual Hall Sensors Note: The following diagrams indicate 3 kinds of incorrect wiring. 1) Both Hall Sensors were lead through with battery input and output positive cables: Fig.9 -10-...
Page 13
2) Both Hall Sensors were lead through with battery input positive cables: Fig.10 3) Both Hall Sensors were lead through with battery output posi- tive cables: Fig.11 -11-...
Page 14
5. Mount the Monitor Mount the Monitor on the wall when wiring is finished. Choose one of the following two ways for installation. 5.1 Flat Surface Installation Mount the Monitor Base on flat surface with M3.9*19 Self Drilling Screws, put the Monitor in the Base and fix it with M4*10 Pan Head Cross Screws.
Fig.13 Groove Installation How To Use 1. Operation Long press power button for 2S to turn on the Monitor. (long press again to turn it off) Power Button Main Page Health Settings Status Page Page Fig.14 Home Page -13-...
Page 16
At the bottom of the Home Page list 3 icons for different pages: Home Page, SOH and Setting. Finish the basic parameter setting in Setting Page before the Monitor can normally work. Note: The parameters marked with * are necessary before first-time use or changing a new battery.
Page 17
SOC:The left power of the battery. :The estimated left working time of the battery. It will show as 99h59m when no load is connected. 3. SOH Page Rated Capacity of Battery Battery Health Status Percentage Actual Battery Capacity Number of Battery Cycles Fig.17 SOH Page Nominal Capacity:The rated capacity of the battery.
Page 18
Battery Full Charge Voltage Battery Rated Battery Drained Capacity Out Voltage Number of Hall Brightness Sensors Automatic Screen Shutdown Time Fig.18 Basic *Battery Capacity Battery Rated Capacity Number of Battery Cells in Series Fig.19 Battery capacity Battery capacity suggests the rated capacity of the battery. This value is a necessary one.
Page 19
*Maximum voltage When the voltage of battery reaches this value, SOC will auto read as 100% and the actual capacity of battery will be counted. Please ensure the battery can reach this value when it is fully charged. It is recommended to set this value as the charging voltage of the charger.
Page 20
Buzzer Switch High Pressure Overcurrent Alarm Alarm Threshold Threshold Low Pressure Alarm Low Battery Alarm Threshold Threshold Fig.20 Alarm Page Alarm Buzzer Switch Turn on/off the Buzzer when the Monitor needs to warn the user. When it is off, the Buzzer won’t give any sound, only warning icon is displayed.
Page 21
*Over current Threshold of over current warning. When the battery current reaches this value for over 5S, the Monitor will give warning with the words OVER AMPS flashing in the Home Page and the Buzzer will give sound until the current drops to lower than the value for over 5S.
Page 22
4.3 Adjust This page is for zeroing the current and cycles when battery is not working Current Zeroing Cycles Zeroing Fig.26 Adjust *Current Zeroing When battery is not working and the current value is not 0, use this to manually set the value to 0. It is recommended to do this every time a battery is connected to the Monitor no matter how many the current reads.
Troubleshooting Fault Description Solution The input and output It is normal the sensor reading gets nuance. current of battery is 0 You can set the current to 0 in Setting Page>- while the Monitor reads Adjust>Current Zeroing. other than 0. Turn on the Monitor and the current keeps Check if the quantity of Hall Sensor is correct in...
Appendix Here attached is the diagram of how to lead the negative cable through Single Hall Sensor or Dual Hall Sensors. Lead the input and output negative cables through Hall Sensor. 1. Single Hall Sensor Lead the negative ends of the battery’s input and output cables(including Monitor power cable) through one single Hall Sensor.
Page 25
2. Dual Hall Sensors Lead the negative ends of the battery’s input cables through one of the Hall Sensor. Lead the negative ends of the battery’s output cables through the other Hall Sensor(including Monitor power cable). Make sure the arrow on the Hall Sensor points to the battery’s negative terminals along the cables.
Page 26
Tip: the following diagrams indicate 2 kinds of correct wiring. Fig.29 Single Hall Sensor Correct Wiring Fig.30 Dual Hall Sensors Correct Wiring -24-...
Page 27
Note: The following diagrams indicate 3 kinds of incorrect wiring. 1) Both Hall Sensors were lead through with battery input and output negative cables: Fig. 31 2) Both Hall Sensors were lead through with battery input nega- tive cables: Fig. 32 -25-...
Page 28
3) Both Hall Sensors were lead through with battery output neg- ative cables: Fig.33 * Current Zeroing When battery is not working and the current value is not 0, use this to manually set the value to 0. It is recommended to do this every time a battery is connected to the Monitor no matter how many the current reads.
Page 31
Modell:ECO-BM100V3 Bedienungsanleitung UNTERSTÜTZUNG Wenn Sie technische Probleme haben und keine Lösung in diesem Handbuch finden können, wenden Sie sich bitte an ECO-WORTHY, um weitere Hilfe zu erhalten. ·Call:1-866 939 8222(US) +44 20 7570 0328(UK) +49 693 1090 113(DE) ·Email: customer.service@eco-worthy.com...
Page 32
Inhalt ........1 Sicherheitsvorkehrungen ........2 Allgemeine Informationen ..........3 Spezifikationen ...........4 Was ist in der Box ...........5 Produktübersicht ...........6 Installation ..........13 Wie verwenden ...........21 Fehlerbehebung ...........22 Anlage...
Sicherheitsvorkehrungen · Vielen Dank für die Auswahl unserer Produkte. Bitte lesen Sie dieses Handbuch sorgfältig durch, bevor Sie dieses Produkt verwenden, da es wichtige Informationen und Ratschläge zur Installation, Verwendung, Fehlerbehebung usw. enthält. Ver- sehentliche Schäden, unbefugte Reparatur, unsachgemäße Lagerung und Verwendung führen zu einem Ausfall der Garantie- abdeckung.
Allgemeine Informationen Dieser Monitor ist für 9-80V Lithium- und Blei-Säure-Batterien konzip- iert. Es enthält einen hochpräzisen Hall-Sensor und 3,5-Zoll-Touch- screen mit sauberer und kurzer Benutzeroberfläche. Mit dem Monitor können Sie den elektrischen Strom, die Spannung, SOC, SOH, Kapazität und Zyklen Ihrer Batterie überprüfen und einstel- len.
Was ist in der Box Item# Name Menge Anmerkung Monitor Hall Sensor 5m Netzkabel 2-polig 5m Hall Sensor Kabel 4-polig Basis Selbstbohrschraube M3,9*19mm Schwenkkopf Kreuzschraube M4*10mm Handbuch Zeichnung der Nutinstallationshilfe...
Produktübersicht Abb. 1 Produktübersicht Item# Name Beschreibung Anzeigen von Informationen und Status Touchscreen des Systems Drücken Sie lange die Taste, um den Monitor ein- oder auszuschalten. Kurzes Ein-/Aus-Taste Drücken zum Aufwachen oder Schließen des Bildschirms Leistungsanzeige Zeigt ein/aus an Schraubverschluss Die Schraube abdecken und verstecken DC IN Port Stromversorgung zum Monitor...
Installation Führen Sie die positiven Enden der Ein- und Ausgangskabel der Batterie durch den Hall Sensor. Das System kann als einer der folgenden 2-Modi installiert werden: 1.Der Eingebaute Sensor 1.1 Definition Zur Erfassung des Batteriestroms ist nur ein einziger Hall Sensor angeschlossen.
Page 39
2. Der Zwillingsplanet Hall 2.1 Definition Zwei Hall-Sensoren werden angeschlossen und die Ein- und Aus- gangskabel der Batterie werden jeweils durch die Hall-Sensoren geführt. (nur 1*Hall-Sensor ist im Lieferumfang enthalten. Wenn Sie duale Hall-Sensoren verwenden müssen, kaufen Sie einen anderen einzeln) Auf diese Weise können der Batterieeingang und der Ausgangsstrom gleichzeitig überwacht werden, aber beachten Sie bitte, dass die 2-Hall-Sensoren nicht zum Ablesen derselben Sache verwendet werden können.
Page 40
3. Schließen Sie den Monitor mit Hall Sensor an 3.1 Der Eingebaute Eensor Verbinden Sie den Hall Sensor mit einem der Anschlüsse (Hall 1/Hall 2) am Monitor mit 5m Hall Sensor Kabel. Abb.4 Verbinden Sie den Monitor mit Single Hall Sensor 3.2 Der Zwillingsplanet Hall Verbinden Sie jeden Hall Sensor mit einem der Anschlüsse am Monitor mit 5m Hall Sensor Kabel.
Page 41
4. Holen Sie sich Netzteil Schließen Sie das 5m Netzkabel an die Batterie an (drehen Sie die 2-Anschlüsse NICHT um) und stecken Sie das andere Ende in den DC IN-Anschluss des Monitors. Abb.6 Schließen Sie die Batterie an den Monitor an Wenn die Installation abgeschlossen ist, sollte das gesamte System wie folgt aussehen: Solar Power Controller...
Page 42
Hall Sensor Pfeilrichtung Hall Sensor Pfeilrichtung Batterieausgang Batterieausgang Positivdraht Positivdraht Abb.8 Monitor System Verdrahtung mit Dual Hall Sensoren Anmerkung: Die folgenden Diagramme zeigen drei Arten von falscher Verkabelung an. 1) Beide Hall-Sensoren wurden mit Batterie-Ein- und Ausgang- skabeln durchgeführt: Abb.9 -10-...
Page 43
2) Beide Hall-Sensoren wurden mit positiven Batterieeingangska- beln durchgeführt: Abb.10 3) Beide Hallsensoren wurden mit positivem Batterieausgang durchgeführt: Fig.11 -11-...
Page 44
5. Montieren Sie den Monitor Montieren Sie den Monitor an der Wand, wenn die Verkabelung abgeschlossen ist. Wählen Sie eine der folgenden zwei Möglich- keiten für die Installation. 5.1 Installation auf flacher Oberfläche Montieren Sie die Monitorbasis auf flache Oberfläche mit M3.9*19 selbstbohrenden Schrauben, setzen Sie den Monitor in die Basis und befestigen Sie ihn mit M4*10 Pan Head Cross Schrauben.
Abb.13 Nutinstallation Wie verwenden Wie ist die Anwendung anzuwenden? Drücken Sie lange die Ein-/Aus-Taste für 2S, um den Monitor einzuschalten. (wieder lange drücken, um es auszuschalten) Ein-/Aus-Taste Startseite Gesundheit Einstellungen Statusseite Seite Abb.14 Startseite -13-...
Page 46
Am unteren Rand der Startseite Liste 3-Symbole für verschie- dene Seiten: Startseite, SOH und Einstellung. Beenden Sie die grundlegende Parametereinstellung unter Einstellungsseite, bevor der Monitor normal arbeiten kann. Anmerkung: Die Parameter, die mit der Markierung gekennzeichnet sind, sind vor dem erstmaligen Gebrauch oder dem Wechsel einer neuen Batterie erforder- lich.
Page 47
“SOC”:Die linke Leistung der Batterie. “ ”:Die geschätzte verbleibende Arbeitszeit der Batterie. Es wird als 99h59m angezeigt, wenn keine Last angeschlossen ist. 3. SOH-Seite Nennkapazität der Batterie Batteriezustand Status Prozentsatz tatsächliche Batteriekapazität Anzahl der Batteriezyklen Abb.17 SOH-Seite “ Nominal Capacity ” :Nennkapazität der Batterie. Es ist der Wert, der in Einstellungsseite>Basic>Batteriekapazität festgelegt ist.
Page 48
Batterie voller Ladespannung Batteriewert Batterie entleert Kapazität Ausgangsspannung Anzahl der Hallen Helligkeit Sensoren Automatische Abschaltzeit des Bildschirms Abb.18 Basic “*Battery Capacity” Batteriewert Kapazität Anzahl der Batterien Zellen in Serie Abb.19 Batteriekapazität Die Batteriekapazität gibt die Nennkapazität des Akkus an. Dieser Wert ist notwendig.
Page 49
“* Maximum voltage ” Wenn die Spannung der Batterie diesen Wert erreicht, liest SOC automatisch als 100% und die tatsächliche Kapazität der Batterie wird gezählt. Bitte stellen Sie sicher, dass der Akku diesen Wert erreichen kann, wenn er vollständig aufgeladen ist. Es wird emp- fohlen, diesen Wert als Ladespannung des Ladegeräts einzustel- len.
Page 50
Buzzer-Schalter Hochdruck Überstromalarm Alarmschwelle Schwellenwert Niederdruckalarm Alarm bei niedrigem Schwellenwert Batteriestand Schwellenwert Abb.20 Alarmseite “Alarm Buzzer Switch” Schalten Sie den Buzzer ein/aus, wenn der Monitor den Benutzer warnen muss. Wenn er ausgeschaltet ist, gibt der Buzzer keinen Ton aus, es wird nur ein Warnsymbol angezeigt. Abb.21 Alarm Summer On “*High voltage”...
Page 51
“*Over current” Schwelle der aktuellen Warnung. Wenn der Batteriestrom diesen Wert für über 5S erreicht, gibt der Monitor eine Warnung mit den Worten ÜBER AMPS auf der Startseite aus und der Buzzer gibt Ton aus, bis der Strom unter den Wert für über 5S fällt. Die War- nung wird ausgelöst, die Worte ÜBER AMPS verschwinden und der Buzzer stoppt.
Page 52
4.3 “Adjust” Diese Seite ist für die Nullstellung des Stroms und Zyklen, wenn die Batterie nicht funktioniert Aktueller Nullpunkt Zyklen Null Abb.26 Anpassen “*Current Zeroing” Wenn die Batterie nicht funktioniert und der aktuelle Wert nicht 0 ist, verwenden Sie dies, um den Wert manuell auf 0 einzustel- len.
Fehlerbehebung Fehler Beschreibung Lösung Der Ein- und Es ist normal, dass die Sensoranzeige Nuan- Ausgangsstrom der cen bekommt. Sie können den Strom auf 0 Batterie beträgt 0, unter Einstellungsseite>Anpassen>Aktuelle während der Monitor Nullstellung einstellen. andere als 0 liest. Schalten Sie den Monitor ein und der Überprüfen Sie, ob die Menge des Hall Sensors Strom springt weiter...
Anlage Hier ist das Diagramm, wie das Negativkabel durch Single Hall Sensor oder Dual Hall Sensoren geführt wird. Führen Sie die negativen Ein- und Ausgangskabel durch Hall Sensor. 1. Der Eingebaute Sensor Führen Sie die negativen Enden der Ein- und Ausgangskabel der Batterie (einschließlich Monitor-Netzkabel) durch einen einzigen Hall-Sensor.
Page 55
2. Der Zwillingsplanet Hall Führen Sie die negativen Enden der Eingangskabel der Batterie durch einen Hall Sensor. Führen Sie die negativen Enden der Ausgangskabel der Bat- terie durch den anderen Hall Sensor (einschließlich Monitor Netzkabel). Achten Sie darauf, dass der Pfeil am Hall Sensor auf die nega- tiven Anschlüsse der Batterie entlang der Kabel zeigt.
Page 56
Tipp: Die folgenden Diagramme zeigen zwei Arten der richtigen Verkabelung. Solar Power Controller Negativer Draht Hall Sensor Pfeilrichtung Abb.29 Der Eingebaute Sensor Correct Verdrahtung Hall Sensor Pfeilrichtung Negativer Draht Negativer Draht Hall Sensor Pfeilrichtung Abb.30 Der Zwillingsplanet Hall Korrekte Verdrahtung -24-...
Page 57
Anmerkung: Die folgenden Diagramme zeigen drei Arten von falscher Verkabelung an. 1) Beide Hall-Sensoren wurden mit Batterie-Ein- und Ausgangs- negativen Kabeln durchgeführt: Solar Power Controller Abb. 31 2) Beide Hall-Sensoren wurden mit negativen Batterieeingang- skabeln durchgeführt: Solar Power Controller Abb. 32 -25-...
Page 58
3) Beide Hallsensoren wurden mit negativen Batterieausgang- skabeln durchgeführt: Solar Power Controller Abb.33 *Aktueller Nullpunkt Wenn die Batterie nicht funktioniert und der aktuelle Wert nicht 0 ist, verwenden Sie dies, um den Wert manuell auf 0 einzustel- len. Es wird empfohlen, dies jedes Mal zu tun, wenn eine Bat- terie an den Monitor angeschlossen ist, unabhängig davon, wie viele der Strom liest.
Need help?
Do you have a question about the ECO-BM100V3 and is the answer not in the manual?
Questions and answers