Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MechMaxx FW8800
Summary of Contents for MechMaxx FW8800
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
TABLE OF CONTENTS SPECIFICATIONS SAFETY SIGNS IMPORTANT SAFETY INFORMATION YOUR SAFETY GENERAL CARDAN SHAFT OPERATION DESCRIPTION REQUIRED EQUIPMENT OF THE TRACTOR PTO SHAFT ADJUSTMENT TRACTOR MOUNTING WIRE ROPE UNWINDING ILLUSTRATED PARTS CATALOGUE PARTS LIST PINCH ROLLER COMPONENT www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model FW8800 Recommended Tractor Power 30-50 hp Pulling Capacity 8800 lbs Winch Type Mechanical, Dry Disc Clutch Average Winching Speed 180 ft/minute Cable Length 200 ft Cable Diameter 3/8 in Cable Type Steel Tractor CAT CAT 1 PTO Input Speed... -
Page 5: Safety Signs
SAFETY SIGNS The rating plate on your machine may show symbols. These represent important information about the product or instruc- tions on its use. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Important Safety Information
Defects should be removed by an expert. Before first use or after significant alterations and at least once a year the winch must be examined by an expert. 6. When using public transport routes observe traffic signs and regulations. www. mechmaxx.com SAFETY... - Page 7 27. On uneven terrain or when not observing the maximum prepared holder. allowed towing angle there is a danger of the winch rolling 33. In the area of the three-point linkage there is a danger over (Figure 4). of injuries due to compression or crushing. www. mechmaxx.com SAFETY...
- Page 8 (See Figure 6). 35. During the tow, it is forbidden to stand between the load and the winch as well as in the danger area between the winch, relay pulley and load. (See Figure 7). FIGURE 7 www. mechmaxx.com SAFETY...
-
Page 9: Cardan Shaft
This rule must also be observed during machine operation. 9. Never switch on the cardan shaft when the engine is turned off. 10. Put the disconnected cardan shaft on the intended holder. www. mechmaxx.com SAFETY... -
Page 10: Operation
(figure F2). loosely during towing. 5. Shorten external and internal slide profiles with the same distance as plastic protection pipes (figure F3). 6. Crop the pipe end, remove fillings and grease the slide positions well (figure F4) www. mechmaxx.com OPERATING... -
Page 11: Illustrated Parts Catalogue
ILLUSTRATED PARTS CATALOGUE www. mechmaxx.com ILLUSTRATED PARTS CATALOGUE... -
Page 12: Parts List
Nut M16 FW40.11 Spacer W-08-Y22 Round Rubber Cover FW40.17 Handle FW40.16 Spacer FW40.15A Link GB/T 5783 Bolt M12*40 GB/T 5783 Bolt M12*50 FW40.8 Rocker Arm Welded Parts FW40.40 Top Pillar GB/T 5783 Bolt M16*65 Gasket FW40.42 www. mechmaxx.com PARTS LIST... - Page 13 Support Foot Welding Parts GB/T 97.1 Washer 30 GB/T 889.1 Nut M30 FW40.30 Brake Pad Assembly GB/T 62.1 Wing Nut M10 FW40.32 Adjustment Handwheel GB/T1243 Chain 12AH-1-74 GB 894.1 Circlip For Shaft A30 GB/T 276 Bearing 6206-2Z www. mechmaxx.com PARTS LIST...
- Page 14 FW40.25 Spacer YB/T5359 Compacted Wire Rope FW40.31 Friction Plate Compression Spring JB/T 7940.1 Greaser M8 GB/T 5783 Bolt M6*16 GB/T 93 Spring Washer 6 GB/T 95 Washer 10 GB/T 5783 Bolt M10*35 GB/T 6170 Nut M12 www. mechmaxx.com PARTS LIST...
-
Page 15: Pinch Roller Component
PINCH ROLLER COMPONENT www. mechmaxx.com ILLUSTRATED PARTS CATALOGUE... - Page 16 Pinch Roller Shaft FW40.5.3 Pinch Roller FW40.5.8 Spacer FW40.5.9 Torsional Spring 2 FW40.5.5 Support Shaft FW40.5.6 Torsional Spring 1 FW40.5.2 Support Weldment GB/T 5783 Bolt M6*16 FW40.5.7 Platen GB/T 93 Washer 5 GB/T 5783 Bolt M5*12 www. mechmaxx.com PARTS LIST...
- Page 18 info@mechmaxx.com...
Need help?
Do you have a question about the FW8800 and is the answer not in the manual?
Questions and answers