Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MechMaxx RT400
Summary of Contents for MechMaxx RT400
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
ADJUSTMENT BEFORE WORKING SAFETY SIGNS STARTING OF THE TILLER SAFETY INSTRUCTIONS SIZING PTO SHFAT SAFETY FIRST MAINTENANCE & LUBRICATION GENERAL SAFETY MAINTENANCE OPERATING SAFETY STORAGE STORAGE SAFETY LUBRICATION MAINTENANCE SAFETY PARTS DIAGRAM OPERATION PARTS LIST BLADE MOUNTING www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model RT400 RT450 RT500 RT600 Power Required 18-35HP 25-45HP 25-50HP 30-60HP Working Width 48 in 53 in 60 in 72 in 57 in 60 in 66 in 78 in Overall Width Working Depth 1in,2.1in,3.1in,5.1in Number Of Flanges Number Of Blades... -
Page 5: Safety Signs
SAFETY SIGNS The rating plate on your machine may show symbols. These represent important information about the product or instruc- tions on its use. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Safety Instructions
An untrained operator jeopardise himself and tractor – particularly during a turnover when the operator bystanders to possible serious injury or death. could be pined under the ROPS or the tractor. www. mechmaxx.com SAFETY INSTRUCTIONS... -
Page 7: Operating Safety
14.Always know what you are hoeing. Never operate Rotary hoe in an area that has hidden obstacles. Remove sticks, stones, wire or other objects from working area before starting. 15.Review safety instructions with all operators annually www. mechmaxx.com SAFETY INSTRUCTIONS... -
Page 8: Operation
PTO Shaft and the bearing seat of the blade shaft. Then check for the looseness of all connecting bolts and nuts, if loose, tighten it at once. If a crack or bent blades are found they must be replaced. www. mechmaxx.com OPERATION... -
Page 9: Sizing Pto Shfat
STEP 4 Use a file to deburr PTO shafts. Clean up all chips, Figure 1-A burrs and filings from both ends of the PTO shaft. STEP 2 Using cut section of the shield as a guide cut shaft off the same amount. (Figure 2) www. mechmaxx.com SIZING PTO SHFAT... -
Page 10: Maintenance & Lubrication
5. Drain and refill gearbox and Gear case oil. Be sure to replace all oil plugs.Drain oil in gearbox by removing the bottom drain plug or right-hand cap.Drain oil in Gear case by removing the bottom plug and tipping tiller backwards. www. mechmaxx.com MAINTENANCE & LUBRICATION... -
Page 11: Parts Diagram
PARTS DIAGRAM www. mechmaxx.com PARTS DIAGRAM... -
Page 12: Parts List
Bolt M12*25 Chain 6 Spring Washer 12 Shackle 6 Bolt M12*30 Rotor Cover Presure Relief Plug M16*1.5 Bonded Washer 16 Lower Pin Plain Washer 10 Bearing 6309 Nylon Nut M10 Oilseal 55*80*8 Bolt M10*40 Rotor Shaft www. mechmaxx.com PARTS LIST... - Page 13 DESCRIPTION Rotor C Blade Nylon Nut M14 Right Plate Oilseal 35*62*8 Bearing 6306 Bolt M12*20 Rotor Cap Supportor R Pin L pin Rubber Cap Bolt M10*20 Grease Fitting M8*1 www. mechmaxx.com PARTS LIST...
- Page 14 PARTS DIAGRAM www. mechmaxx.com PARTS DIAGRAM...
- Page 15 Tab Washer For Round Nut 30 Round Nut M30*1.5 Driven Gear Bearing 30311 Oilseal 75*42*8 Shaft Cover Gasket Shaft Cover Shaft Oilseal 70*40*8 Bearing 30308 Plug Input Shaft Bearing 30208 Oilseal 55*38*8 Front Gasket Front End Cap www. mechmaxx.com PARTS LIST...
- Page 16 info@mechmaxx.com...
Need help?
Do you have a question about the RT400 and is the answer not in the manual?
Questions and answers