Related Manuals for De Raat Anchor 7000
Summary of Contents for De Raat Anchor 7000
-
Page 1: Table Of Contents
Anchor User manual Anchor 7000 Index General information Code length / silent alarm Batteries Interfaces Dual code + time delay Blocking time Overview user rights Opening the lock Opening the lock with a dual code Opening the lock with an active time delay... -
Page 2: General Information
Anchor 7000 User manual General information Interfaces Depending on the facility, additional restrictions Upon delivery, only the interface for analog may apply to opening a lock. A combination of input units from the Anchor series is active. these restrictions is also possible: Other interfaces must be set via the setup menu. -
Page 3: Overview User Rights
Anchor 7000 User manual Overview user rights Master 0 123456(0 User 1..8 User 9 Opening lock The lock releases the bolt movement for approximately 3 seconds after entering a valid code. After entering the code, open the safe Example. Factory code within this period. -
Page 4: Opening The Lock With An Active Time Delay
Anchor 7000 User manual Opening the lock with an active time delay Start with entering a user or master code: The delay is started by entering a valid opening code. The lock can then be opened by re-entering a valid user code within the opening time window (this does not have to be identical to the start code). -
Page 5: Menu Functions
Anchor 7000 User manual Menu functions Using the buttons on the keyboard, various If a dual code is active, a valid user code must function menus can be accessed and desired be entered before entering the menu. settings can be made. Selecting these menus is a Only after entering the code, the menu crucial step in customizing the lock’s functionality... -
Page 6: Changing The Master Code With Emergency Key
Anchor 7000 User manual 0 Reset master code with emergency key On the Anchor 7000, the code change function can be used in conjunction with the emergency key to reset the master code. E.g. setting the master code to 1234560 Open the lock with the emergency key. -
Page 7: Creating A User Code
Anchor 7000 User manual 1 Creating a user E.g.: creating user 3 Menu: Creating a user Enter master code: A new user code will only be accepted if the code differs by one digit in two places from an existing code. -
Page 8: Deleting A User Code
Anchor 7000 User manual 3 Deleting a user If the dual code is active, the user who enabled the menu entry by entering a code cannot be deleted. When the opening delay is activated, users 1 to 8 can be deleted, but user 9 cannot. The functionality that allows user 9 to open the lock even if the opening delay is activated is retained. -
Page 9: System Setup
Anchor 7000 User manual 6 System setup In addition to the connection for an analog keyboard, locks from the Anchor series have an additional interface that can be used for serial communication [UART] or for connecting a signal box (for example from the Primor series) [IO]. Before use, the operating mode must be set accordingly. -
Page 10: Switch Off The Analogue Keypad
Anchor 7000 User manual 6 System setup 6-1-2 Disable the analog keypad Menu ‘System setup’ Enter master code: !!! NB !!! After the analog keypad is disabled, it can only be reactivated via the serial interface! Sub-menu for changing mode:... -
Page 11: Silent Alarm Configuration
Anchor 7000 User manual 6 System setup 6-2 Silent alarm configuration By activating the “silent alarm function” the number of required code digits is increased from 6 to 7 digits (VdS code difference required). If users have already been created, the last position is automatically set to 0. -
Page 12: Activate/Deactivate Remote Locking
Anchor 7000 User manual 6 System setup 6-3 Activate/deactivate remote locking Using external signals to lock the system allows the system to be controlled from outside without the need for physical access to the system itself. This function should only be activated if the alarm system or signal box is connected, otherwise there is a risk of blocking the system, which cannot be deactivated without external wiring. -
Page 13: Battery Warning
Anchor 7000 User manual 6 System setup 6-5 Battery level warning Change the battery warning threshold to, for example, 5.67 V Menu ‘System setup’ Enter master code: By parameterizing the warning threshold, the locking system can be adapted to different battery types. -
Page 14: User Overview
Anchor 7000 User manual 7 User overview Menu ‘User overview’ Enter master code: This function provides an overview of the number of free or already occupied users. This allows you to selectively check whether Number of user to be checked:... - Page 15 In cooperation with De Raat Security Products BV De Raat Security Products SA De Raat Security Products Ltd. Edelgasstraat 5 Gareelmakersstraat 10 Unit 32 Axis Park 2718 SX Zoetermeer 2200 Herentals Manasty Road Nederland België Orton Southgate Peterborough, PE2 6UP...
Need help?
Do you have a question about the Anchor 7000 and is the answer not in the manual?
Questions and answers