Table of Contents
Advertisement
Quick Links
Electronic lock
Users manual Wittkop 7202
Contents
1.Important notes
1.1 Explanation of terms
5. Correction with the „C" button
6. Battery charge monitoring, replacing the battery
7. Emergency opening 8. Programming the electronic lock
8.1.1 Programming a new primary combination using the
emergency opening lock
8.3.2 Deleting a timed delay period
8.5.1 Opening the lock with an interlock activated
8.5.2 Deleting an interlock
1. Importent notes
Please read these instructions carefully and completely before
putting the lock in operation.
•
Replace the 0 _ 1 2 3 4 5 6 factory combination
immediately by programming your own master
combination; see Section 8.1.
•
Do not use any personal data for your new master or user
combination.
7202
•
The maximum permissible interval between any two
keypad entries is 30 seconds. If this limit is exceeded, then
the entire procedure will have to be repeated from the
beginning.
•
A signal tone sounds each time a button is pressed.
•
A 10-second time-out period will be started after invalid
combinations have been entered in three consecutive
attempts.
•
Do not damage the inspection seal on the lock as the
guarantee will otherwise be invalidated.
Explanation of terms
User number = User number (abbreviated UNo.)
UNo. = 0 for master
UNr. = 1 to 5 users
Code = A series of digits, e.g. 4 7 6 2 3 9
Combination = A series of digits required to open the lock. It
comprises the: User number and code:
Example for the master combination 0 _ 6 5 4 7 2 1
Example of a user combination 3 _ 8 7 9 5 8 3
Factory combination = The initial combination, programmed at
the factory. The combination for this electronic lock has been
pre-set to 0 _ 1 2 3 4 5 6
Master combionation = Combination used by the master to open
the lock
User combination = Combinations for additional users. All user
combinations are subordinate to the master combination.
P - No. = Program number
LED = Light-emitting diode at the keypad.
Advertisement
Table of Contents
Related Manuals for De Raat 7202
Summary of Contents for De Raat 7202
- Page 1 7202 Electronic lock Users manual Wittkop 7202 Contents • 1.Important notes The maximum permissible interval between any two 1.1 Explanation of terms keypad entries is 30 seconds. If this limit is exceeded, then 1.2 General the entire procedure will have to be repeated from the 2.
- Page 2 1.2 General 5. Correction with the C button If you press the „C“ button during the course of an entry sequence, Even though operation is very simple, you should nonetheless then all digits previously entered will be canceled. Any read these instructions carefully and completely before programming mode which might have been commenced will also starting, in order to prevent operating errors.
- Page 3 Programming the electronic lock Programming modes Before you use your safe for the first time it is necessary, for security reasons, to enter your own personal combination; the factory combination must not be retained. Programming is possible only with the door open and with the electronic lock released.
- Page 4 8.3 Programming a timed delay period Possible only with the electronic lock open and only with the master combination. Explanation: Timed delay period = Period between entering a combination the first time and the time at which the electronics clear the lock for entry of a combination the second time, to actually open the safe. Relaese period = Period of time available, once the timed delay period has expired, to open the safe by entering a combination.
- Page 5 8.4.1 Starting a time-lock period The time-lock period will commence automatically, immediately after it has been programmed. During the time-lock period the red LED will blink every 30 seconds and the keypad will not res- pond to any entries at all. Once the programmed time-lock pe- riod has elapsed the electronic lock can be opened using either the master combination or a user combination.
- Page 6 9. Triggering a silent alarm To trigger a silent alarm, increase by 1 the final digit of your master or user combination We can assume no liability for malfunctions caused by erroneous resetting or by the application of force or by improper handling, nor for damages to property or assets which, for example, are due to not closing the safe properly.
Need help?
Do you have a question about the 7202 and is the answer not in the manual?
Questions and answers