Chauvet, Chauvet Professional, the Chauvet logo, and COLORado are registered trademarks or trademarks of Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate a claim. In addition, keep the box and contents for inspection.
• In the event of a serious operating problem, stop using immediately. If this Chauvet product requires service, contact Chauvet Technical Support. COLORado Solo Bar 1 User Manual Rev. 1...
LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity. COLORado Solo Bar 1 User Manual Rev. 1...
2. Introduction Description The COLORado Solo Bar 1 is a 4-cell, IP65-rated, RGBWwL LED batten. Producing a full range of color and flexible whites with RGB, RGBWw, and full RGBWwL control, the COLORado Solo Bar 1 combines homogenized squares for end-to-end direct-view pixel-mapped looks. Performs equally well as a cyc, footlight, or down light with High output and long throw.
5.86 in 148.75 mm 5.86 in 148.73 mm 6.16 in 156.58 mm 8.36 in 212.4 mm 4.09 in 104 mm 6.3 in 160 mm 6.27 in 159.16 mm 8.2 in 208.4 mm COLORado Solo Bar 1 User Manual Rev. 1...
Green/Yellow Green/Yellow Green Power Linking It is possible to power link COLORado Solo Bar 1 products. See the table below for the current draw at each voltage and frequency: 100 V, 60 Hz 120 V, 60 Hz 208 V, 60 Hz...
Setup Master/Slave Connectivity The Master/Slave mode allows an COLORado Solo Bar 1 (the master) to control one or more COLORado Solo Bar 1 products (the slaves) without a DMX controller. One COLORado Solo Bar 1 becomes the master when running an auto program or in Static mode.
If the COLORado Solo Bar 1 has already been paired with the CRMX™ transmitter, the Signal Strength Indicator on top of the display will show the strength of the signal. In this case, the COLORado Solo Bar 1 is ready to work in Wireless mode.
1. Power on the products. 2. Connect the DMX out of the COLORado Solo Bar 1 with the latest software to the DMX in of the COLORado Solo Bar 1 that needs to be updated. 3. Go to the Update Firmware level of the receiving product’s menu.
• Other Fixture Type: The target fixture and main fixture are from different product series (e.g., a COLORado Solo Bar 1 as the target fixture and a Maverick Silens 2 Profile as the main fixture). 6. Select the file that needs to be uploaded. The message “Are you sure?” will appear on the screen.
When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity. Procedure The COLORado Solo Bar 1 comes with Omega brackets. The user can directly attach a mounting clamp to these Omega brackets. Make sure the clamp is capable of supporting the weight of this product. For the Chauvet Professional line of mounting clamps, go to http://www.trusst.com/products.
Glare Shield and Filters The COLORado Solo Bar 1 comes with a glare shield, which can be stored or installed in a slot on the side of the product, and 4 filters including the clear protective filter which comes installed. The product keeps the glare shield and filter in place with a spring-loaded locking plate.
Setup Guide Pins The COLORado Solo Bar 1 has 2 guide pins which can assist in keeping linearly mounted products together in a straight line. To access and use the guide pins: 1. Install the glare shield upright or remove it from the product, as shown in Glare Shield and Filters.
Press <MENU> repeatedly to exit to the previous main level. Passcode After being prompted to enter the passcode, press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>. Menu Map Refer to the COLORado Solo Bar 1 product page on www.chauvetprofessional.com for the latest menu map and software.
Page 20
4-cell, 33-channel: dimmer, 16-bit XY, XY Ext. 33ch strobe, virtual color wheel, control Green Green Blue Blue Fixed Dimmer Static Warm White White Colors <000–255> Lime Lime Red and blue Green and blue COLORado Solo Bar 1 User Manual Rev. 1...
Page 21
C1060 - Dk Red Amber C1650 - Magenta C6170 - Dk Magenta C6020 - Lt Lavender C5030 - Lt Blue C5020 - VLt Blue C5430 - Lt Blue 2 C5070 - Blue C5050 - Md Blue COLORado Solo Bar 1 User Manual Rev. 1...
Page 22
Settings Color User Blue <125–255> Sets maximum blue LED value Calibration Calibration Warm White Sets maximum white LED value Lime Sets maximum lime LED value Factory Calibration Color calibration set by factory COLORado Solo Bar 1 User Manual Rev. 1...
Page 23
The “Other Fixture Type” option under Upgrade Firmware can only be selected for connected products compatible with the Upload 03 (the first 2 digits of the item code must be 03). COLORado Solo Bar 1 User Manual Rev. 1...
Use control configurations to operate the product with a DMX, Art-Net™, or sACN controller. Control Mode The COLORado Solo Bar 1 works with DMX, Art-Net™, and sACN control signals. To select the protocol: 1. Go to the Protocol main level.
IP Mode It is possible to set the IP address of the COLORado Solo Bar 1 manually, by the network, or to a preset static address specific to each product. To set the IP mode, follow the instructions below: 1.
Operation Virtual Color Wheel The COLORado Solo Bar 1 includes a feature called the Virtual Color Wheel (VCW). This feature is available as a standalone control mode and as a control channel in select DMX personalities. More than 30 premixed colors, custom blended by Chauvet engineers, are available to call up for easier programming.
012 116 063 255 024 The color temperatures above are simulated renditions of the color output produced compared with a tungsten lamp at the specified color temperature. Chauvet makes no guarantee of the color output accuracy. DMX Channel Assignments and Values...
31 Strobe 4 000 255 See the Strobe Chart – 32 Virtual Color Wheel 4 000 255 See the Virtual Color Wheel Chart 33 Control 000 255 See the Control Chart COLORado Solo Bar 1 User Manual Rev. 1...
000 255 0–100% 9 11 21 16 18 20 35 Red 3 000 255 0–100% – – – 22 – – – 36 Fine red 3 000 255 0–100% COLORado Solo Bar 1 User Manual Rev. 1...
Page 31
– 20 34 38 66 Virtual Color Wheel 000 255 See the Virtual Color Wheel Chart – – – – 31 35 39 67 Control 000 255 See the Control Chart COLORado Solo Bar 1 User Manual Rev. 1...
000 255 0–100% Color temperature 4 000 255 See the Color Temperature Chart Tint 4 (Default to 128) 000 255 -25–+25% green Control 000 255 See the Control Chart COLORado Solo Bar 1 User Manual Rev. 1...
000 255 0–100% Color temperature 2 000 255 See the Color Temperature Chart Tint 2 (Default to 128) 000 255 -25–+25% green Control 000 255 See the Control Chart COLORado Solo Bar 1 User Manual Rev. 1...
000 255 See the Control Chart HSV 4ch Channel Function Value Percent/Setting 000 255 0–100% Saturation 000 255 0–100% Value 000 255 0–100% Control 000 255 See the Control Chart COLORado Solo Bar 1 User Manual Rev. 1...
1. Go to the Static main level. 2. Select the Color X-Fade Speed option. 3. Select Off (to turn off the fade transition between colors) or X-Fade Speed 1–4 (from fast to slow). COLORado Solo Bar 1 User Manual Rev. 1...
3. Select from No (do not reset) or Yes (reset). Wireless to DMX The COLORado Solo Bar 1 can convert wireless CRMX™ to wired DMX output. To enable or disable this function: 1. Go to the Wireless Setting main level.
2. Select the Information option. Temperature To view the temperatures of the display board and the LEDs in °C: 1. Go to the Info & Updating main level. 2. Select the Temperature option. COLORado Solo Bar 1 User Manual Rev. 1...
2. Select No (do not reset) or Yes (reset). Web Server The COLORado Solo Bar 1 Web Server can be accessed by any computer on the same network as the product. It allows network access to system information, settings such as control protocol and starting address, color output testing, and the ability to change the Web Server password.
3.47184 Fuse 10.41552 Power block, power box and side covers, trim strip 6.94368 Vacuum Test Measurements Use the IP Tester from Chauvet Professional to ensure the product has been reassembled correctly by following the information below: Parameters Values Method Positive...
4 Cell: 13, 13, 12, 16, 20, 40, 31, 35, 39, 67, 13, or 33 Ordering Product Name Item Name Item Code UPC Number COLORado Solo Bar 1 COLORADOSOLOBAR1 03032277 781462226251 UL 1573 CSA C22.2 No. 166 E113093 COLORado Solo Bar 1 User Manual Rev. 1...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. COLORado Solo Bar 1 User Manual Rev. 1...
Need help?
Do you have a question about the COLORado Solo Bar 1 and is the answer not in the manual?
Questions and answers