Hanwha Vision QNV-C8013R/QNV-C8023R User Manual

Hide thumbs

page of 43

/ 43
Bookmarks

Quick Links

Download this manual

NETWORK CAMERA

User Manual

QNV-C8013R/QNV-C8023R

QND-C8013R/QND-C8023R

QNO-C8013R/QNO-C8023R

Need help?

Do you have a question about the QNV-C8013R/QNV-C8023R and is the answer not in the manual?

Questions and answers

Summary of Contents for Hanwha Vision QNV-C8013R/QNV-C8023R

Page 1 NETWORK CAMERA User Manual QNV-C8013R/QNV-C8023R QND-C8013R/QND-C8023R QNO-C8013R/QNO-C8023R...
Page 2 Network Camera User Manual Copyright ©2024 Co., Ltd. All rights reserved. Hanwha Vision Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
Page 3 23. The operating temperature for the QND-C8013R/QND-C8023R products is -10°C to +45°C(14°F to +113°F). 5. Do not use this apparatus near water. 24. The operating temperature for the QNV-C8013R/QNV-C8023R/QNO-C8013R/QNO-C8023R products is 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
Page 4 overview Class construction The ITE is to be connected only to PoE networks without routing to the outside plant. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3af shall be a UL Listed device with the output evaluated as a Limited Power protective earthing connection.
Page 5 CONTENTS OVERVIEW NETWORK CONNECTION AND Important Safety Instructions Connecting the Camera Directly to Local Recommended PC Specifications Area Networking SETUP Recommended Micro SD/SDHC/SDXC Connecting the Camera Directly to a DHCP Memory Card Specifications Based DSL/Cable Modem NAS recommended specs Using Device Manager Optional Accessories for Installation Automatically searching camera Configuring IP address...
Page 6 overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Recommended browser: Chrome Recommended products : QNAP NAS, Synology NAS ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based)
Page 7 Vandal Dome Camera Dome Camera Bullet Camera QNV-C8013R/QNV-C8023R QND-C8013R/QND-C8023R QNO-C8013R/QNO-C8023R English _7...
Page 8 overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available. Pole Mount Back Box Model name Wall Mount and Pole Mount Hanging Mount Gang Plate Housing Audio/alarm cable (Direct Assembly) and Tilt Mount SBP-125WMW1 SBP-400WMW (Indoor Wall&Pole Mount) (Wall&Pole Mount) QNV-C8013R/ *SBD-110GP1 required for...
Page 9 Pole Mount Back Box Model name Wall Mount and Pole Mount Hanging Mount Gang Plate Housing Audio/alarm cable (Direct Assembly) and Tilt Mount QNO-C8013R/ QNO-C8023R SBD-140PMW SBO-140BW SBO-090GP *SBO-090GP required for installation Ceiling Mount Model name Corner Mount Parapet Mount Cabinet Assembly Individual Parts...
Page 10 WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Mount-plate Wiring hole cover Camera-body Dome-cover <QNV-C8013R/QNV-C8023R> IR LED Audio/Alarm cable port Illumination Sensor Lens Reset button Option (not included) Micro USB...
Page 11 INSTALLATION 2. Remove the camera body by turning the mount plate fastening screws counterclockwise. Note that it is not necessary to loosen the screws completely. The camera jack connected to the external cable is not waterproof. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 12 vandal dome camera Inserting a Micro SD card Removing a Micro SD card Insert the micro SD card into the micro SD card slot on the camera body in the arrow direction. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
Page 13 Installation (mount plate) When connecting cables from the side, first remove the wiring hole cover of the camera body. [Directly installing on wall/ceiling] 1. Place the mount plate on the desired location considering the direction to be monitored, mark the locations for the screw holes and cable holes, and then drill the holes.
Page 14 vandal dome camera Installation (camera body) 2. Remove the protruding part of the 1-hole cable bushing that was removed from the camera body. 3. Use the cap installer to pass through the RJ45 cable. Use a cable bushing compliant with the network cable to be connected. Cap Installer Camera main: use a cable with the diameter of Ø5 to Ø6.5 You can only use a network cable with a diameter of Ø6.5 or less.
Page 15 5. Insert the cable bushing of the network cable into the camera body. [Installing audio/alarm cables (separately sold)] 7. Remove the cable bushing next to the PoE port from the camera body. 6. Connect the network cable connector to the PoE port of the camera body. 8.
Page 16 vandal dome camera 9. Connect the audio/alarm cable connector to the audio/alarm cable port of the camera body. 11. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. (page 18) If you tilt the lens, you may need to adjust the lens as this may block the screen. Connect a monitoring device to the USB port and then monitor and adjust it.
Page 17 Waterproofing of cable connections Be careful not to alter the monitoring direction of your camera. When installing the camera, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
Page 18 vandal dome camera ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA Tilt Lens Rotation ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.
Page 19 dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Camera-body Fixing cover Wiring hole cover Dome-cover <QND-C8013R/QND-C8023R> IR LED Alarm cable port Illumination Sensor Lens Reset button Option (not included) SPP-C7200 Micro USB port Micro SD card slot PoE Port Use installation screws of at least M4, L30 for the installation of this product.
Page 20 dome camera INSTALLATION 2. Remove the fixing cover from the camera body. Precautions before installation Ensure you read out the following instructions before installing the camera: ~ Select an installation site that can hold at least 5 times the camera’s weight. ~ Stuck-in or peeled-off cables can cause damage to the product or a fire.
Page 21 Inserting a Micro SD card Removing a Micro SD card Insert the micro SD card into the micro SD card slot on the camera body in the arrow direction. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
Page 22 dome camera Installation (mount plate) Installation (camera body) [Directly installing on wall/ceiling] [Installing the network cable] 1. Place the camera body on the desired location considering the direction to be monitored, mark the 1. Connect the network cable connector to the PoE port of the camera body. locations for the screw holes, and then drill the holes.
Page 23 3. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the 3. Assemble the dome cover. camera” section. (page 24) If you tilt the lens, you may need to adjust the lens as this may block the screen. Make sure to firmly tighten the fastening screws so that there is no water damage issue.
Page 24 dome camera ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA Be careful not to alter the monitoring direction of your camera. Tilt Lens Rotation ` Adjusting the monitoring direction Adjust the direction of IR LEDs not to hinder their view by an instrument. You can adjust the camera direction only when the camera is fixed on the ceiling.
Page 25 bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Sunshield fixing screw Sunshield <QNO-C8013R/QNO-C8023R> Camera body Port box PoE port Use installation screws of at least M4, L30 for the installation of this product. Reset button Audio I/O port...
Page 26 bullet camera INSTALLATION Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. The camera jack connected to the external cable is not waterproof. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 27 Installation 4. Loosen the fixing screws of each control part to adjust the monitoring direction of the camera. Note that it is not necessary to loosen the screws completely. [Directly installing on wall/ceiling] Connect a monitoring device to the USB port and then monitor and adjust it. 1.
Page 28 bullet camera 5. Assemble the sunshield on the camera body with the provided sunshield fixing screws. 1.5 ~ 2 N·m (1.1 ~1.47 lb·ft) <Tilt> When adjusting the camera monitoring direction, loosen the corresponding fixing screws, adjust the camera, and then tighten the screws.
Page 29 How to connect the RJ45 waterproof cable to a LAN cable Waterproofing of cable connections When installing the camera, please waterproof it with waterproof butyl rubber tape (can be purchased in 1. Insert it through the arrow direction. stores) so that water does not leak from the gap of the cable connected to the outside. 1.
Page 30 Ethernet The Micro USB port of the product is provided for easier installation, and is not recommended for monitoring purposes. <QNV-C8013R/QNV-C8023R/QND-C8013R/QND-C8023R> The Micro USB port of the product is provided for easier installation, and is not recommended for monitoring purposes.
Page 31 Powering and networking Connecting WiFi Connect the PoE device with the PoE port of the camera. Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Connect and use a PoE enabled router. Use a PoE device that complies with the IEEE 802.3af standard. Smartphone Setup 1.
Page 32 Frequency range: 40-16,000 Hz Impedance: 1,500 Ω Sensitivity: -40±3 dB (7.1-14.1 mV) The audio/alarm cables for QNV-C8013R/QNV-C8023R need to be purchased separately. Speaker Microphone 1. Connect the MIC port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to.
Page 33 Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. The alarm cable for QND-C8013R/QND-C8023R/QNV-C8013R/QNV-C8023R need to be purchased separately. SIGNAL LINE - BLACK : GND / ORANGE : ALARM IN / BROWN : ALARM OUT...
Page 34 network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
Page 35 USING DEVICE MANAGER If using a Broadband Router Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ~ IP Address : Enter an address falling in the IP range provided (https://www.HanwhaVision.com). by the Broadband Router.
Page 36 network connection and setup Configuring Dynamic IP AUTOMATICALLY CONFIGURING IP Receive IP address from DHCP 1. Click the camera from the list that you want to automatically ~ Example of the Dynamic IP environment configure the IP. QNV-C8013R - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2.
Page 37 PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
Page 38 network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
Page 39 web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
Page 40 web viewer PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 characters, you must use at least 3 system over the network.
Page 41 appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION Voice is not recorded even though When an Windows 10 user accesses ~ You must enable the <Audio In> check box in <Basic> - <Video Profile>. ~ This is what happens when microphone driver has been set to Realtek driver. audio input settings are configured.
Page 42 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.

This manual is also suitable for:

Qnv-c8013r Qnd-c8023r Qno-c8013r Qno-c8023r Qnv-c8023r Qnd-c8013r