Operation - Vivanco 8 IN 1 UNIVERSAL LCD REMOTE CONTROL QUOTSOFT TOUCHQUOT Programming Manual

Program Macros
Application)
You can program a sequence of upto 10
control commands to be output on pressing
one one single key called MACRO-key. Upto 3
MACRO-keys are available.
Please proceed as follows, see Fig. 11:
1 Press and hold SET for 3 seconds, then
set MACRO with the ▲ or ▼ button. Confirm
this function by pressing OK.
2 MACRO1 appears in the display. Set
MACRO1, 2 or 3 using the ▲ or ▼ button.
Confirm this function by pressing OK.
3 SET UP is displayed. Confirm this
function by pressing OK.
4 SELECT KEYs is displayed. Then press
a sequence of keys, which shall be output
later, when you press MACRO and 1 ,2 or 3.
E.g. TV, POWER, DVD, POWER, AMP,
POWER for all devices power off.
5 Press OK when sequence input is
finished and macro shall be stored.
Delete Macros
Please proceed as follows, see Fig. 12:
1 Press and hold SET for 3 seconds, then
set MACRO with the ▲ or ▼ button. Confirm
this function by pressing OK.
2 MACRO1 appears in the display. Set
MACRO1, 2 or 3 using the ▲ or ▼ button.
Confirm this function by pressing OK.
3 SET UP is displayed. Confirm this
function by pressing OK.
4 Select DELETE using the ▲ or ▼ button.
5 Then press OK and SURE DELET is
displayed. Confirm this function by pressing
OK. SUCCESS is displayed.
6 Then press EXIT several times to quit the
deletion mode.
Control Any Device On AUX
You can use the AUX device key to control any
device. E.g. if you want to control a 2
AUX key, please proceed as follows, see Fig.
13:
1 Press and hold SET for 3 seconds, then
CODE SETUP is displayed. Confirm this
function by pressing OK.
2 DEV SEARCH is displayed. Set CODE
SHIFT using the ▲ or ▼ button. Confirm this
function by pressing OK.
3 Any device, e.g. TV 010 is displayed.
Press device key, e.g. VCR, OK and enter
code number of required to be by AUX
controlled device, e.g. VCR. Confirm this
function by pressing
displayed.
4 Then press EXIT several times to return
to main control menu.
Vivanco GmbH, D-22926 Ahrensburg, E-Mail
(Home Cinema
nd
VCR by
OK. SUCCESS is
: hotline@vivanco.de
UR 820 LCD UNIVERSAL CONTROLLER
Backlight
To save battery capacity you can switch off the
LCD illumination. To do so, proceed as follows:
1 Press and hold SET for 3 seconds, then
set CONFIGURE with the ▲ or ▼ button.
Confirm this function by pressing OK.
2 TIME SETUP appears in the display. Set
LIGHT using the ▲ or ▼ button. Confirm this
function by pressing OK.
3 Switch the light ON or OFF using the ►
or ◄ button. Confirm this function by pressing
OK.
4 Then press EXIT several times to quit the
setting mode.
Adjusting the contrast
You can adjust the contrast to improve
readability:
1 Press and hold SET for 3 seconds, then
set CONFIGURE with the ▲ or ▼ button.
Confirm this function by pressing OK.
2 TIME SETUP appears in the display.
Adjust the CONTRAST using the ▲ or ▼
button. Confirm this function by pressing OK.
3 Set the contrast to the desired level using
the ► or ◄ button. Confirm this function by
pressing OK.
4 Then press EXIT several times to quit the
setting mode.
Default settings
You can reset your remote control to its factory
default setting, e.g. to correct a malfunction, as
follows. This deletes all your settings.
- This function is recommended only in the event of
your remote control malfunctioning seriously.
1 Press and hold SET for 3 seconds, then
set CONFIGURE with the ▲ or ▼ button.
Confirm this function by pressing OK.
2 TIME SETUP appears in the display. Set
CLEAR ALL using the ▲ or ▼ button. Confirm
this function by pressing OK.
3 The display then shows SURE CLEAR?.
Confirm this function by pressing OK.

Operation

You operate your appliances basically in
exactly the same way as if you were using the
original remote controls, except that you must
first press a device button (TV, DVD, etc.) to
control the required device. As the symbols on
the UR 820 LCD could differ from those on the
original remote controls you may have to try
out all the buttons in order to find the functions.
Scanning of Programs
You can scan the TV or DVB (SAT, CBL, DTT
etc.) programs by:
1 Pressing TV or DVB key,
2 Press and hold the SCAN key for about 4
seconds.
, Helpline: +49 (0) 4102 231135