Page 2
CONTENTS INTRODUCTION SUPPLIED PART S SAFETY INSTRUCTIONS INSTALLATION GUIDELINES FRONT SHOCK INSTALLATION REAR SHOCK INSTALLATION FOX FACTORY DSC MAINTENANCE WARRANTY CONTACT...
Page 3
FOX recommends that you become completely familiar with the handling characteristics of your modified vehicle before operating it under rigorous conditions, helping to avoid potential rollover situations and other loss of control events. FOX further recommends that you use appropriate protective equipment at all times when operating your vehicle.
Page 4
SUPPLIED PARTS SHOCK ASSEMBLY FOX PN DESCRIPTION NOTES 885-24-270 FRONT KIT 985-24-270-L/R FRONT, LEFT/RIGHT SHOCK Performance Series 885-24-271 REAR KIT 985-24-271-L/R REAR, LEFT/RIGHT SHOCK 883-26-166 FRONT KIT 983-26-166-L/R FRONT, LEFT/RIGHT SHOCK Performance Elite Series 883-26-273 REAR KIT 983-26-273-L/R REAR, LEFT/RIGHT SHOCK...
Page 5
FOX direct-replacement shocks are gas-charged and are highly pressurized. Placing shocks in a vise or clamp, applying heat, or attempting to open or service the shock without the proper tools and training can result in SERIOUS INJURY or DEATH. Do not attempt to modify, puncture or incinerate a FOX direct-replacement shock absorber.
Page 6
• DO NOT install any FOX product without the necessary special tools, expertise and chassis lift or you will subject yourself to the risk of SERIOUS INJURY or DEATH. If you elect to not use a chassis lift...
Page 7
FRONT SHOCK INSTALLATION NOTICE: Medium-strength thread-lock is recommended on all bolts. 1. Please read the installation guidelines on page 4 for instructions on how to properly lift and secure the vehicle. 2. Remove both front wheels from the vehicle. 3. Pull the fender liner from the wheel well (Fig. 1). Fig.
Page 8
It may be necessary to support or raise the vehicle axle in order to remove bolts and for installation of new FOX shock. Do not discard bolts and nuts, as they will be used with the FOX shock installation.
Page 9
Fig. 6: Mounted Performance Elite Reservoir. Fig. 7: Mounted Performance Series Reservoir. FENDER LINER TRIMMING NOTICE: Fender liner trimming is required for Performance Elite applications to ensure correct fitment. 1. Test fit the fender liner and assess how much trimming is required. Draw a cut line on the fender liner (Fig.
Page 10
FOX shock. Do not discard bolts and nuts, as they will be used with the FOX shock installation. 1. To remove rear stock shocks, first, remove the bolt securing the shock to the axle.
Page 11
FOX FACTORY DSC EVO DUAL SPEED COMPRESSION EVOLUTION (DSC EVO) ADJUSTER SETTINGS DSC EVO HIGH- AND LOW-SPEED COMPRESSION 7 POSITIONS CLOSED OPEN (FULL (FULL COUNTER CLOCKWISE) POSITION 4 CLOCKWISE) LEAST AMOUNT GREATEST AMOUNT OF COMPRESSION OF COMPRESSION DAMPING SOFTEST DAMPING FIRMEST...
Page 12
Before adjusting preload or the crossover ring, clean the threads of the shock body for easier adjustment and mitigating wear. FOX SERVICE AND UPGRADES HAVE YOUR FOX SHOCKS SERVICED BY FOX TECHNICIANS. CALL OUR SERVICE CENTER AT 619.768.1800 TO GO OVER THE SERVICE AND UPGRADE OPTIONS AVAILABLE FOR YOUR PRODUCT. ONCE YOU’VE SETUP YOUR SERVICE AND/OR UPGRADES YOU WILL...
Page 13
Should it be determined by FOX in its sole and final discretion, that a FOX suspension product is covered by this warranty, it will be repaired or replaced, by a comparable model, at FOX’s sole option, which will be conclusive and binding. THIS IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. ANY AND ALL OTHER REMEDIES AND DAMAGES THAT MAY OTHERWISE BE APPLICABLE ARE EXCLUDED, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR PUNITIVE DAMAGES.
Page 14
CONTACT FOX RACING SHOX A DIVISION OF FOX FACTORY INC. SALES 750 Vernon Way, Suite 101 El Cajon, CA 92020 1.800.FOX.SHOX (1.800.369.7469) orsales@ridefox.com SERVICE 13461 Dogwood Drive Baxter, MN 56425 1.800.FOX.SHOX (1.800.369.7469) servicemn@ridefox.com...
Need help?
Do you have a question about the PERFORMANCE 2.0 Series and is the answer not in the manual?
Questions and answers