Advertisement
Quick Links
Oshkosh Corporation Classification ‐ Restricted
LED-6
Operation and Safety Manual
Models
LED‐6
LED‐8
1001309415
October 09, 2023
ISO 9001 Lic 6080
1001309415
JLG Industries (Australia)
Oshkosh Corporation
LED-8
Page 1-1
09OCT23
Oshkosh Corporation Classification ‐ Restricted
LED-6
LED-8
Customer Support
JLG Industries
(Port Macquarie)
11 Bolwarra Road
PORT MACQUARIE
NSW 2444
Phone: (02) 6581 1111
JLG Industries
(Queensland)
223 Fison Avenue West
Eagle Farm QLD 4009
Phone: (07) 3309 9111
JLG Industries
(NSW)
358 Park Road
REGENTS PARK NSW 2143
Phone: (02) 8718 6300
JLG Industries
(New Zealand)
2b Fisher Cresent
Mt Wellington, Auckland
New Zealand
Phone: + 64 9276 1728
1001309415
JLG Industries (Australia)
Oshkosh Corporation
JLG Industries
(Victoria)
30-32 Cyber Loop
Dandenong
VIC 3175
Phone: (03) 9554 4333
JLG Industries
(Western Australia)
39 Kewdale Road
Kewdale, PERTH WA 6105
Phone: (08) 9356 9811
JLG Industries
(SA)
9 Nucera Court
GREEN FIELDS SA 5107
Phone: (08) 8259 8777
Page 1-2
09OCT23
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for JLG LED-6
Summary of Contents for JLG LED-6
- Page 1 JLG Industries (New Zealand) October 09, 2023 2b Fisher Cresent Mt Wellington, Auckland New Zealand Phone: + 64 9276 1728 ISO 9001 Lic 6080 1001309415 JLG Industries (Australia) Page 1-1 1001309415 JLG Industries (Australia) Page 1-2 Oshkosh Corporation 09OCT23 Oshkosh Corporation 09OCT23...
- Page 2 Take time to read and understand this book thoroughly. If you are uncertain about GENERAL any of the information presented, contact your JLG Service Office before operations commence. SAFETY PRECAUTIONS All instructions in this manual are based on the machine being used under the operating conditions for which it was designed.
- Page 3 If there is a question on DECAL WILL HAVE A RED BACKGROUND. application and/or operation, JLG Industries Customer Support Department should be consulted on (02) 6581 1111 (Australia). INDICATES A POTENTIALLY HAZARDOUS SITUATION. IF NOT AVOIDED, COULD RESULT IN SERIOUS INJURY OR DEATH.
- Page 4 DO NOT ERECT THE MAST OF THE applicable safe operating distances required when undertaking the various wiring in any way. LED-6 OR LED-8 LIGHTING TOWER from overhead power lines. procedures outlined. IN WINDS EXCEEDING 100 km/hr. Contact local authorities for the NOTE: Safety precautions applicable ...
- Page 5 CONTROLS IDENTIFICATION parked prior to use. Barriers, fences MODELS LED-6 and LED-8 Before operating a new machine it and warning signs may need to be Strobe Light / Beacon must be carefully inspected for any erected to ensure awareness of the evidence of damage resulting from unit in operation.
- Page 6 The rear/front outriggers and/or front leg are used to level and stabilise the lighting tower on non-level surfaces. Interior Service light switch Control Panel: 4 Hydraulic-Outrigger Machine 1001309415 JLG Industries (Australia) Page 1-11 1001309415 JLG Industries (Australia) Page 1-12 Oshkosh Corporation...
- Page 7 FROM POWER LINES AS DESCRIBED panel is a fourth outrigger leg. Release IN SECTION 1-SAFETY PRECAUTIONS. the remote locking pin Withdraw the outrigger leg outwards to the locked 1001309415 JLG Industries (Australia) Page 1-13 1001309415 JLG Industries (Australia) Page 1-14 Oshkosh Corporation...
- Page 8 LED-6 LED-8 B. Mast Set-Up Instructions C. Turning-On Lights Lights/Engine Control module Both LED-6 and LED-8 use the same controller to operate and monitor all lighting tower systems. The controller module is factory pre-set with two machine stop/start modes. 1) Manual Start/Stop...
- Page 9 Setting interface. The first line is current locked in the stowed position. date and time and the second line is the 1001309415 JLG Industries (Australia) Page 1-17 1001309415 JLG Industries (Australia) Page 1-18...
- Page 10 TO THE UNIT AND POSSIBLE INJURY doors closed. PERSONNEL CLOSE PROXIMITY. Maximum mass of the LED-6 fitted with Overriding Brake Retract and stow the front and rear Lockout Lever manually deployed outriggers…1550 kg out-riggers and transport legs.
Need help?
Do you have a question about the LED-6 and is the answer not in the manual?
Questions and answers