Advertisement
Quick Links
MOBILE EXTENDING MITRE SAW
STAND
90249
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Related Manuals for Draper 90249
Summary of Contents for Draper 90249
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
- Page 2 Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact.
- Page 3 CONTENTS TITLE PAGE INTRODUCTION ......................2 REVISION HISTORY ......................2 UNDERSTANDING THIS MANUAL ................2 COPYRIGHT NOTICE......................2 CONTENTS CONTENTS........................3 WARRANTY WARRANTY........................4 INTRODUCTION SCOPE ..........................5 SPECIFICATION ......................5 HANDLING AND STORAGE ....................5 HEALTH AND SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR MITRE SAW STANDS ........6 TECHNICAL DESCRIPTION IDENTIFICATION ......................8 UNPACKING AND CHECKING PACKAGING ........................9...
- Page 4 This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period.
- Page 5 This model has the added benefit of transport wheels, allowing the stand to be transported with a mitre saw in-situ. Any application other than that it was intended for, is considered misuse. 4.2 SPECIFICATION Stock No ...........................90249 Part No ..........................MSSM168D Extending beam lengths: ..................1067 – 1657mm Max. Height: To beam:...........................775mm...
- Page 6 HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR MITRE SAW STANDS When using this product in conjunction with a mitre saw there are steps that should be taken to make sure that you, as the user, remain safe: – Before use, read and fully understand the appropriate instruction documentation supplied with the mitre saw, paying particular attention to relevant health and safety information.
- Page 7 HEALTH AND SAFETY INFORMATION Move the machine as instructed. If the machine is hand held, do not carry it by the power supply cable. If the product is heavy, employ a second or third person to help move it safely or use a mechanical device.
- Page 8 TECHNICAL DESCRIPTION 6.1 IDENTIFICATION (11) (12) (12) (11) (10) Support rollers. (2) Support roller locking knobs. (3) Transport wheels. (4) Workpiece support. (5) Legs. (6) Leg locking levers. Extending beams. (8) Extending beam locking knobs. (9) Mitre saw mounting bracket locking handles. (10) Transport handle.
- Page 9 Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the product.
- Page 10 ASSEMBLING THE MITRE SAW STAND The following tools (not included) are required to assemble the mitre saw stand: (17) – Cross slot screwdriver. (21) – 13mm wrench or socket. (20) 8.1 ASSEMBLE TRANSPORT HANDLE – FIGS.1 – 2 – Utilising 2 sets of fixings, thread the screws (17) with lock washers (20) and washers (21) in the same order as indicated inset in Fig.1.
- Page 11 ASSEMBLING THE MITRE SAW STAND 8.3 ASSEMBLE WHEELS – FIGS.5 – 7 – Slide the axle (13) through the axle bracket (17) (17) (15) (13.1). – Turn the axle until the machined end fits into the inside bracket hole. – Place one small Ø8mm washer (21) and M8 locking nut (15) onto the axle –...
- Page 12 ASSEMBLING THE MITRE SAW STAND 8.5 MOUNTING A MITRE SAW – FIGS.9 – 16 Warning! Risk of accidental starting and serious personal injury. Isolate the power source by either removing the power supply plug from (12.3) (12.2) the socket, or battery from the tool, before attaching it to the mitre saw stand.
- Page 13 OPERATION 9.1 ROLLER BARS/EXTENSION BAR ADJUSTMENT– FIGS.17 – 18 Warning! Do not use the mitre saw stand for scaffolding or as a ladder. Make sure to securely tighten all fasteners before using. Warning! Maximum load capacity for this mitre saw stand is 150kg. Warning! Mitre saws used on the stand should not exceed a combined overall height of 152.4cm (60") from the floor.
- Page 14 OPERATION 9.4 TRANSPORTATION – FIGS.21 – 24 Warning! Risk of unsafe operation. Ensure proper footing and use caution when wheeling the mitre saw stand to prevent tipping or loss of balance. – Lift up on the end of the mitre saw stand with transport wheels (3).
- Page 15 11. OPTIONAL ACCESSORIES 11.1 OPTIONAL ACCESSORIES A full range of accessories are available from Draper Tools. Please visit our website for details: www.drapertools.com - 17 -...
- Page 16 12. DISPOSAL 12.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: ●...
- Page 17 13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Read the instruction manual. Wear face mask and safety glasses. Wear ear defenders. Wear protective gloves. Do not abandon into the environment. Keep out of the reach of children. Warning! - 19 -...
- Page 18 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
- Page 19 ASSEMBLING THE MITRE SAW STAND – Remove the mounting brackets from the frame and attach them onto the under side of the (16) mitre saw using the supplied fittings. (22) Note: Make sure that you fit the brackets to (18) the saw the correct way around, so that the carry handles (12.4) are facing outwards (Fig.14).
- Page 20 Warning! To ensure safety and reliability of this tool, any service or repairs must be performed by an authorised Draper Tools service technician. – Unauthorised third party repairs and/or replacement of non-Draper parts to this product will invalidate the warranty and, could in the worst case, cause a life threatening safety hazard.
Need help?
Do you have a question about the 90249 and is the answer not in the manual?
Questions and answers