Related Manuals for SRAM I-MOTION 3
Summary of Contents for SRAM I-MOTION 3
- Page 1 user manual betriebsanleitung notice d’utilisation handleiding brugsanvisning bruksanvisning DualDrive · December 2002...
- Page 2 Please take the time to read these life, or which prevent possible operating instructions carefully. damage to the bicycle. Your SRAM i-MOTION 3 System is almost maintenance-free. Should Special advice to assist in the you have any queries that are...
-
Page 3: Table Of Contents
» Repair work / wear parts A S S E M B L Y O F C O M P O N E N T S T E C H N I C A L D A T A i-MOTION 3 · June 2006... -
Page 4: T H E S R A M I - M O T I O N 3 S Y S T E M
T H E S R A M i - M O T I O N 3 S Y S T E M A modern bicycle derailleur should be sporty, load shiftable, intuitive to use and durable! With the new i-MOTION 3, SRAM delivers an internal gear hub that meets and exceeds all these requirements! i-MOTION 3 gear hub Load shiftable. -
Page 5: O P E R A T I O N
This will lead to a trip to the repair shop. Read the applicable user manual for each bicycle equipped with i-BRAKE or band brakes. i-MOTION 3 · June 2006... -
Page 6: M A I N T E N A N C E A N D C A R E
Decrease shift cable ten- sion by turning the barrel adjuster (2) at the shifter. » Shift the twist shifter to the 3rd gear and check again, until there isn‘t any play in the shift cable. i-MOTION 3 · June 2006... -
Page 7: Remove And Fit Rear Wheel
(4). Loosen the axle nuts (5) and remove the nuts and the re- taining washers (6) underneath them. If applicable, unscrew the frame clamp connection (7) of the brake lever. » Remove the rear wheel. i-MOTION 3 · June 2006... - Page 8 (5) between the two straps of the frame clamp (6). The frame clamp must be seated on the frame with no play. Use only self-locking nuts! Tightening torque: 2 – 3 Nm (18 – 27 in.lbs.). i-MOTION 3 · June 2006...
- Page 9 1st gear. Make the cable connection by hooking in the link (7) of the shift cable to the cable nipple (8) on the hub. Slide the plastic retainer (9) completely onto the cable stop bracket (10). i-MOTION 3 · June 2006...
-
Page 10: Cleaning And Lubrication
C L E A N I N G A N D L U B R I C A T I O N C L E A N I N G » Your SRAM i-MOTION 3 compo- nents are well protected from external evironmental impacts. -
Page 11: Repair Work / Wear Parts
Please check these » Unauthorized work on your parts regularly and replace them i-MOTION 3 system could endan- timely. ger you and your warranty may become void. » Please contact your qualified bike dealer regarding any questions or problem you may have. -
Page 12: A S S E M B L Y O F C O M P O N E N T S
Slide the cable stop bracket (4) onto the axle end of the sprocket side. Thereafter mount the washer with rubber insert (5) to fix the the cable stop bracket. » Place the rear wheel into the rear frame. i-MOTION 3 · June 2006... - Page 13 (10) between the two straps of the frame clamp (11). The frame clamp must be seated on the frame without play. Use only self-locking nuts! Tightening torque: 2 – 3 Nm (18 – 27 in.lbs.). i-MOTION 3 · June 2006...
- Page 14 (re-adjust if needed). » Never ride without the handlebar 2.5 mm grips. The turning grip of the twist 1.7 Nm shifter could become loose. This (15 in.lbs.) can result in severe injury. i-MOTION 3 · June 2006...
- Page 15 1st gear. Make the cable connection by hooking in the link (1) of the shift cable to the cable nipple (2) on the hub. Slide the plastic retainer (3) completely onto the cable stop bracket (4). i-MOTION 3 · June 2006...
- Page 16 Decrease shift cable ten- » Shift the twist shifter to the 3rd sion by turning the barrel gear and check again, until there adjuster (2) at the shifter. isn‘t any play in the shift cable. i-MOTION 3 · June 2006...
- Page 17 A S S E M B L Y O F C O M P O N E N T S i-MOTION 3 · June 2006...
- Page 18 T E C H N I C A L D A T A i-MOTION 3 with back pedal brake G E A R H U B Speeds Brake With back pedal brake Over Locknut Dim., OLD 130 mm Length, L...
- Page 19 T E C H N I C A L D A T A 10x1 10x1 i-MOTION 3 · June 2006...
- Page 20 WORLD HEADQUARTERS Chicago, Illinois U.S.A. SRAM Corporation 1333 North Kingsbury, 4th floor Chicago, Illinois 60622 phone: +1-312-664-8800 fax: +1-312-664-8826 EUROPEAN HEADQUARTERS Amersfoort, The Netherlands SRAM Europe Basicweg 12-D 3821 BR Amersfoort The Netherlands phone: +31-33-450-6060 fax: +31-33-457-0200 ASIAN HEADQUARTERS Taichung, Taiwan SRAM Taiwan No.