Sealey MW19 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
Save this instruction manual for safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts
9
list and diagrams. Keep your invoice. Keep the instruction manual and invoice in a safe and dry place for future reference.
Only use on firm, level, unobstructed surfaces which are capable of supporting the metal shaping station.
9
Ensure metal shaping station is fixed to surface capable of supporting the station and accessories.
9
Always use the metal shaping station in a well lit, clean and dry place.
9
Make sure surface is firm under foot. Preferably concrete.
9
DO NOT use non-original parts; use of such parts may be dangerous will affect the warranty.
8
Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep metal shaping station dry.
9
Keep children and unauthorised persons away from the work area.
9
Ensure that the unit is properly and securely assembled before use.
9
Use the right tool for the job. DO NOT attempt to force a small tool or attachment to do the work of a larger industrial tool. DO NOT
9
modify this tool and DO NOT use this tool for a purpose for which it was not intended.
Dress properly. DO NOT wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive
9
clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair.
Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal
9
filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and
mists.
Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing
9
accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept
clean, dry, and free from oil and grease at all times.
Stay alert. Watch what you are doing, use common sense. DO NOT operate any tool when you are tired.
9
Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the
9
warranty. Only use accessories intended for use with this tool.
Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician.
9
Workpiece may be sharp. After bending or cutting workpieces use caution. Be aware of sharp edges or sharp shreds of metal that may
9
be created. Use heavy duty gloves when handling the workpiece.
WARNING! When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of
‰
children.
WARNING! Failure to comply with these instructions may result in damage to the station or other property and/or personal injury.
‰
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
‰
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
WARNING! When using this tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage.
‰
DO NOT force tool. It will do the job better and more safely at the rate for which it was intended. DO NOT use inappropriate
8
attachments in an attempt to exceed the tool capacity.
DO NOT overreach. Keep proper footing and balance at all times.
8
DO NOT operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your
8
judgment or reflexes are impaired while taking drugs. If there is any doubt, DO NOT operate the tool.
2. INTRODUCTION
Versatile station designed to hold T-dollies and/or sandbags securely. Accommodates most sizes of dollies, offering flexibility for
different metal shaping tasks. Features mounting holes on the base for easy installation on the floor, ensuring stability during use.
Provides a stable platform for leather panel beating sandbag when needing to conduct metal forming tasks. Overall height of 885mm
creates a compact workstation for convenient metal shaping operations, allowing easy access to tools and sandbag mounting plate for
sheet metal work.
© Jack Sealey Limited
METAL SHAPING STATION FOR HOLDING
T-DOLLIES & SANDBAGS
MODEL NO:
Wear hearing
Protection
Original Language Version
MW19
MW19 Issue 2 30/08/24