Table of Contents
Advertisement
brightneSS/contraSt/Saturation/SharpneSS/gamma
Picture Setting adjustment is available for the following options.
brightness: Adjust overall brightness of the image.
contrast: Adjust bright areas (white level) in the image.
Saturation: Adjust the dullness or richness of image color. A color
with absolutely no saturation is going to be gray. A color that is 100%
saturated is in its most intense form.
Sharpness: Picture sharpness could be easily lost during the
recording/playback process. Adjust sharpness to improve the fine
details of the picture
gamma: Adjust intensity of the picture non-linearly. Select when
an image's dark portions appears obscure or bright portions become
brighter than necessary.
NOTES
• The level of adjustment for Brightness, Contrast, Saturation and
Sharpness (all defaulted to "0") range from -4 to +4 while Gamma is
from 0.761 up to 1.315.
• Refer also to the item on PICTURE SETTING ADJUSTMENT at the VIDEO
SETTING section of the REFERENCE page.
video output
Turn ON/OFF either HDMI audio/video OUT or VGA OUT. HDMI OUT and
VGA OUTPUT can only be turned ON one at a time – if HDMI is set to ON,
VGA is automatically set to OFF and vice versa.
Scart (europe model onlY)
SCART carries both composite video and RGB signals. Select the video
output signal that will be routed over SCART OUT.
cvbS: Select to output composite video signals.
rgb: Split the signal into the three fundamental colors Red, Green and
Blue (RGB) resulting to greater picture resolution and elimination of
artifacts associated with traditional composite video signals.
AUDIO SETUP MENU
digital audio output
Each DVD disc has a variety of audio output options. Set the player's Digital
Audio Output according to the type of audio system you use.
dolbY digital/pcm: Select DOLBY DIGITAL/PCM if an active digital
output is supplied to a Dolby Digital decoder (or an amplifier or other
equipment with Dolby Digital decoder). In this mode, the M 55 will
automatically switch between Dolby Digital and PCM depending on
the program encoded on the disc, with Dolby Digital given priority. DTS
is not possible with this setting.
Stream/pcm: Select Stream/PCM if an active digital output is supplied
to an amplifier or other equipment with DTS decoder, Dolby Digital
decoder and MPEG decoder. If the disc is neither of stream or PCM
format, there will be no audio output at this option.
pcm: Select when connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital or MPEG will be automatically
uSing the m 55 – Setup menu
downmixed to two-channel PCM audio. DTS cannot be downmixed to
two-channel PCM.
off: Select to turn off digital audio output. With this option, you will
have purely analog audio output.
NOTES
• If an active digital audio output signal is supplied to a receiver or other
equipment without a corresponding digital decoding capability, a very
loud noise may be produced which could permanently damage the
speakers.
• The DTS DVD disc sound is played back only when the DVD player is
connected to a receiver with a DTS decoder.
5.1 Speaker Setup
This option allows you to configure the 5.1 CHANNEL AUDIO OUT of the
M 55. Digital audio output will not be affected by the settings done in this
section. Use [
] keys to select a menu item and [
the settings of the selected item.
Speaker Selection
Select a speaker that you want to adjust - Front L, Center, Front R, Rear R,
Rear L or Subwoofer.
Size
Small: Select if you have connected to a system with speakers that lacks
significant deep bass response - about 150Hz below.
large: Select if you have connected to a system with full frequency
speakers capable of deep bass response.
none: Select when you do not have a certain speaker connected.
Front L/R speaker's size can only be set to "Large" or "Small". If Front L/R
speaker's size is set to "Small", Rear and Centre speaker's size can only be set
to "Small" or "None".
Subwoofer's size can be set only to "Large" or "None".
volume
Adjust the output level of the selected speaker from -10dB up to a
maximum of 0dB.
diStance
Setting the Distance lets the speakers know how far the sound has to travel
to reach your set listening point. This allows the sound from each speaker to
reach the listener at the same time.
Distance can be adjusted within 1ft (0.30m) up to 20ft (6m).
DISTANCE setting is not applicable for Subwoofer.
OPERATION
] keys to adjust
1
Advertisement
Table of Contents
