Advertisement
Quick Links
Advertisement
Related Manuals for Samsung LS E65 Series
Summary of Contents for Samsung LS E65 Series
- Page 1 Repair Guide Basic Model LS24E65UDPG/ZA Applicable Mode LS**E65* Ver.1.0...
- Page 2 Contents 1. Precautions 1-1. Safety Precautions ..........................1-1 1-1-1. Warnings ..........................1-1 1-1-2. Servicing the Product ......................1-1 1-1-3. Fire and Shock Hazard ......................1-1 1-1-4. Product Safety Notices ......................1-2 1-2. Servicing Precautions ........................1-3 1-2-1. General Servicing Precautions ...................1-3 1-3. Electrostatically Sensitive Devices (ESD) Precautions ..............1-4 1-4.
- Page 3 Samsung- authorized service provider. Any damage or defect to product resulting from a repair, or an attempt to repair, the product by any person other than a Samsung certified service provider will not be covered by the warranty.
- Page 4 Samsung’s liability in any case shall be limited to the greatest extent permitted by law. Samsung reserves the right, at its sole discretion, to change, modify, add or remove portions of any part of this manual at any time. It is your responsibility to check the manual periodically for changes. Your use of the manual...
- Page 5 Precautions 1. Precautions 1-1. Safety Precautions • Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
- Page 6 Precautions 6. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that no wires or components touch thermally hot parts.
- Page 7 Following the repair by a non-authorised service provider, self-repair or non-professional repair of the product, Samsung is not liable for any damage to the product, any injury or any other product safety issue caused by any attempt to repair the product which does not carefully follow these repair and maintenance instructions.
- Page 8 Precautions 1-3. Electrostatically Sensitive Devices (ESD) Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
- Page 9 Precautions 1-4. Installation Precautions 1. For safety reasons, more than a people are required for carrying the product. 2. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. 3. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
- Page 10 Disassembly and Reassemble 2. Disassembly and Reassemble • As this monitor has parts that are sensitive to static electricity, be careful when handling them. Warning • Disconnect the Product from the power source before disassembly. • Follow these directions carefully; never use metal instruments to pry apart the cabinet. Caution Assembly Misc P-jig-2017 Delphinus...
- Page 11 Disassembly and Reassemble Description Picture Description Screws Open the buckle of both sides that be adjacent to the center ones in order. Open the buckle of both corners then. Rotate the monitor in the same plane and put one side of monitor close to the operator, and then open the buckles in the right and left side of monitor.
- Page 12 Disassembly and Reassemble Description Picture Description Screws Lift the back cover of the monitor and open the bottom buckles. You can remove the back cover completely then. Remove the LVDS, LED Harness, function LVDS wire and speaker wire cable then remove the shield-cover.
- Page 13 Disassembly and Reassemble Description Picture Description Screws Remove the 6 screws shown in the figure and remove the Bracket support. 6003-000264 (M3xL6) 6003-001439 (M4XL8) Remove the main PBA and SMPS board from the Shield-Cover. • Reassembly procedures are in the reverse order of disassembly procedures. Note...
Need help?
Do you have a question about the LS E65 Series and is the answer not in the manual?
Questions and answers