Advertisement
Quick Links
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION
INSPECTION REQUIREMENTS IN YOUR AREA.
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-
BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN
PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
READ AND KEEP THIS MANUAL FOR REFERENCE
This manual is available for free download on the manufacturer's website. It is a copyrighted document. Re-sale
is strictly prohibited. The manufacturer may update this manual from time to time and cannot be responsible
for problems, injuries, or damages arising out of the use of information contained in any manual obtained from
unauthorized sources.
Printed in Canada
INSTALLATION MANUAL
HEP55
(VB00025 model)
Safety tested according to ULC S627 and ASTM
E1509 by an accredited laboratory
INSTALLATION BY A PROFESSIONAL
IS STRONGLY RECOMMENDED
Stove Builder International inc.
250, rue de Copenhague,
St-Augustin-de-Desmaures (Québec) Canada
G3A 2H3
Technical services : 1-877-356-6663
Email : tech@sbi-international.com
https://www.occanada.com/ca/fr/
46378IA
2024-10-17
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Ventis VB00025
Summary of Contents for Ventis VB00025
- Page 1 INSTALLATION MANUAL HEP55 (VB00025 model) Safety tested according to ULC S627 and ASTM E1509 by an accredited laboratory INSTALLATION BY A PROFESSIONAL IS STRONGLY RECOMMENDED Stove Builder International inc. 250, rue de Copenhague, St-Augustin-de-Desmaures (Québec) Canada G3A 2H3 Technical services : 1-877-356-6663 Email : tech@sbi-international.com...
- Page 2 1. SAFETY INFORMATION WARNING We highly recommend that our pellet burning hearth THIS STOVE IS MOBILE HOME APPROVED products be installed and serviced by professionals AND REQUIRES INSTALLATION OF A FRESH who are certified in the United States by NFI (National AIR KIT, SOLD SEPARATELY.
- Page 3 NOTICE WARNING DO NOT INSTALL IN ANY FIREPLACE. This stove has been developed and built for residential supplementary heat source. Commercial and industrial use is prohibited and will void the CAUTION warranty. MAINTAIN PROPER VENTILATION. IT IS IMPORTANT THAT ADEQUATE OXYGEN IS NOTICE BEING SUPPLIED TO THE FIRE FOR PROPER COMBUSTION.
- Page 4 TABLE OF CONTENTS 1. SAFETY INFORMATION ................2 2. GENERAL FEATURES .................. 5 2.1 OVERALL DIMENSIONS (E).....................6 2.2 REGULATIONS COVERING PELLET STOVE INSTALLATION ........6 2.3 CERTIFICATION LABEL LOCATION ................6 3. CLEARANCES TO COMBUSTIBLE MATERIALS ........7 3.1 CLEARANCES TO COMBUSTIBLES MATERIALS, WALLS AND CEILING ....7 3.2 FLOOR PROTECTION ......................8 4.
- Page 5 2. GENERAL FEATURES Recommended 3 in. (75mm) chimney diameter Flue outlet diameter 3 in. (75mm) Type of chimney ULC/ORD-C441 CAN/ULC S609 UL 641 (TYPE L) Approved for alcove installation Approved for mobile home installation ‡ Shipping weight 277 lb (without option) Appliance weight 235 lb (without option)
- Page 6 2.2 REGULATIONS COVERING PELLET 2.1 OVERALL DIMENSIONS (VB00025) STOVE INSTALLATION 24 7/8" When installed and operated as described in these 632mm instructions, this pellet stove is suitable for use as a freestanding heater in residential installations. In Canada, the CSA B365 Installation Code for Solid Fuel Burning Appliances and Equipment and the CSA C22.1 Canadian National Electrical Code are to be...
- Page 7 3. CLEARANCES TO COMBUSTIBLE MATERIALS RECOMMENDED CLEARANCES FOR The clearances shown in this section applies to MAINTENANCE VB00025. CANADA 12" (305 mm) 12" (305 mm) The clearances shown in this section have been determined by tests according to procedures set out...
- Page 8 FLOOR PROTECTION CANADA** 6" (152 mm) 6" (152 mm) From door opening From door opening 6" (152 mm) 6" (152 mm) From door opening From door opening CAUTION STOVE MUST PLACED CONTINUOUS (GROUTED JOINTS) NONCOMBUSTIBLE MATERIAL SUCH AS CERAMIC TILE*, CEMENT BOARD, BRICK, MINIMUM CLEARANCES MILLBOARD OR EQUIVALENT, OR ANY OTHER CANADA...
- Page 9 4. VENTING SYSTEM 4.2 RECOMMANDATIONS In Canada, we recommend that you use a listed pel- CAUTION let vent that meets the CAN/ULC S609 or ULC/ORD CONNECT THIS STOVE ONLY TO A LISTED C441 Standard. A pellet vent listed to ULC S629M is PELLET EXHAUST VENTING SYSTEM FOR USE also suitable for installation with this stove.
- Page 10 Here is an example to help you calculate Equivalent Vent Length. On the following figure the EVL can be calculated like this: CAUTION 2 feet of horizontal run (2 X 1' EVL) = 2' of EVL 90° elbow or "Tee" (1 X 5' EVL) =5' of EVL TO REDUCE THE RISK OF SMOKE SPILLAGE 12 feet of vertical run...
- Page 11 4.4 TERMINATION LOCATION CANADA Refer to NFPA 211 (USA) or CSA B365 (Canada) for rules for the distance of exit terminal from windows and openings. The exit terminal of a mechanical draft system, other than a direct vent appliance shall be located AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED VENT TERMINAL...
- Page 12 4.5 DIRECT VENT SYSTEM 4.6.2 THROUGH ROOF INSTALLATION In Canada: The permitted termination locations for a direct vent system are the same than those permitted with a regular pellet vent system. In the Unites States : The permitted termination location for a direct vent system are the same than those permitted with a regular pellet vent system except for the following : The exit terminal shall be located not less than 9"...
- Page 13 4.6.4 THROUGH AN EXISTING MASONRY 4.6.3 THROUGH A FACTORY BUILT CHIMNEY FIREPLACE NOTICE NOTICE Before installation, the chimney must be cleaned The structural condition of the masonry chimney and inspected by a qualified chimney sweep or must first be inspected by a qualified chimney installer.
- Page 14 4.6.5 THROUGH AN EXISTING MASONRY 4.6.6 FACTORY-BUILT METAL CHIMNEYS CHIMNEY IN MOBILE HOMES For use in a mobile home (if allowed), this stove is to be connected to a 6» double wall factory built chimney pipe conforming to ULC-S629 or UL 103HT standards for 650°C Factory-built chimney.
- Page 15 7.1 THERMOSTAT LOCATION 6. MOBILE HOME INSTALLATION Location of the thermostat is very important to obtain NOTICE comfort and efficiency from your stove. For mobile home installation, it is mandatory to Locate the thermostat 4 to 5 feet above the floor in connect the stove to an outside combustion air accordance with applicable building codes.
- Page 16 7.2 WIRED THERMOSTAT 7.3 WIRELESS THERMOSTAT Before installing the thermostat, unplug the power If you are using a wireless thermostat or a hand cord from the power outlet. held thermostatic remote control, connect the two thermostat wires to the terminal block located at the First, connect the two thermostat wires to the terminal rear on the right hand side of the stove while facing it.
- Page 17 A rodent guard (minimum 1/4” wire mesh) must be used at the termination. All connections must be secured and airtight by either using the appropriately sized hose clamp and/or UL-181-AP foil tape. Make sure that the fresh air intake back draft shutter functions freely.
- Page 18 9. APPLIANCE SET-UP Make sure the fresh air intake back draft shutter works freely. 9.1 GENERAL Install the baffle Test the door seal by closing and latching the door on a strip of paper. Test all around the door. The paper should not slip out easily.
- Page 19 10. WIRING DIAGRAM INSTALLATION MANUAL HEP55 Page 19...
- Page 20 11. EXPLODED VIEWS AND PARTS LIST DP00070 DP00072 AND DP00071 Page 20 INSTALLATION MANUAL HEP55...
- Page 21 SECTION A SECTION B INSTALLATION MANUAL HEP55 Page 21...
- Page 22 SECTION C SECTION D Page 22 INSTALLATION MANUAL HEP55...
- Page 23 SECTION E SECTION F INSTALLATION MANUAL HEP55 Page 23...
- Page 24 SECTION G SECTION H Page 24 INSTALLATION MANUAL HEP55...
- Page 25 SECTION I SECTION J INSTALLATION MANUAL HEP55 Page 25...
- Page 26 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your stove, please provide the model number and the serial number. We reserve the right to change parts due to technology upgrade or availability. Contact an authorized dealer to obtain any of these parts. Never use substitute materials.
- Page 27 Part Description 44098 HOPPER LID SAFETY SWITCH 30013 HINGE 2'' X 1 1/2'' SE69785 EXHAUST PIPE ASSEMBLY 21392 EXHAUST ADAPTER GASKET 30093 BOLT 1/4-20 X 3/4" HEX GRADE 5 SE44193 EXHAUST FAN WITH GASKETS 30094 HEX SCREW WASHER HEAD 1/4-20 X 3/4" F ZINC TYPE 30220 FLANGED LOCKNUT 1/4-20 SE44095...
- Page 28 Part Description 30021 SELF TAPPING SCREW 8-32 "F" TYPE X 7/16" FLAT HEAD PHILLIPS BLACK 30439 SPRING CLAMP ZINC PLATED BRIGHT CHROMATE DIP 30464 INTERFAST #8-32 X 1/2’’ ZINC 21400 COMBUSTION FAN GASKET SE44147 AXIAL BLOWER ASSEMBLY 115V 9W 92 X 92 X 38 PL69799 AIR CONTROL BRACKET 30777...
Need help?
Do you have a question about the VB00025 and is the answer not in the manual?
Questions and answers