Product service centre ...............2 Sending commands to Cyrus components ........8 FCC Notice* ................3 Switching on Cyrus source components ........8 Cyrus remote commands ............8 WELCOME TO THE WORLD OF CYRUS ........4 Menu map .................9 Preparations for Installation ............4 DAC FILTERS ................10 INSTALLATION ................4 Key to the rear panel drawing ...........4...
Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. Cyrus 40 CD User Instructions...
Product service centre For product service or technical advice, contact only authorised Cyrus service centres. Contact details for Cyrus distributors may be found on the Cyrus website at www. cyrusaudio.com. Cyrus 40 CD User Instructions...
• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. *115V products Cyrus 40 CD User Instructions...
• Quick-Start guide and respected manufacturers of hi-fi equipment. After removing these items, please retain the packaging. Now is a good time to register your new Cyrus product. Install the CD player in a well ventilated location away from To register, click...
CAUTION: Connecting to the system amplifier • Disconnect both the 40 PSU and 40 CD from the mains. • Plug the multi-pin interconnect from the 40 PSU into • Connect a suitable stereo RCA phono interconnect the 40 PSU socket on the back panel.
Key to the front panel drawing 1. Standby and indicator 5. Play / Pause 2. CD loading slot 6. Previous track 3. IR / proximity sensors 7. Next track 4. Stop / Eject 8. Display window Cyrus 40 CD User Instructions...
When unattended for a long period (holidays etc) mains power should be disconnected. Standby When mains power is connected, the standby touchpad (CYRUS) is used for power control. When in standby, the touchpad colour will be red. When set to standby, all settings in use are retained. Auto-standby To save energy standby will set automatically after 20 minutes if left in pause or stop modes.
Switching on Cyrus source components • Press the CD key to switch on a Cyrus CD player and send commands to the CD player and an amplifier. • Press the ST key to switch on a Cyrus audio streamer and send commands to the streamer and an amplifier.
Level 5 Cyrus Devices LED Brightness Device Group Level 1 Unlinked Level 2 Group A Level 3 (default) Group B Level 4 Group C Level 5 Group D Cyrus Devices (Lists devices) (Displays 40 PSU information) Cyrus 40 CD User Instructions...
New firmware versions will be available from the ‘Support’ Low and equal levels of pre- and post-ringing. No phase pages of the Cyrus website www.cyrusaudio.com. shift but can introduce high frequency aliasing at a higher If new firmware is available, this will be packaged with level than linear phase, fast roll off.
No Remote Operation The handset may Press the CD button and retry not be set to control commands. a CD player. Remote control lights flash This indicates that Replace the batteries. the batteries are flat. Cyrus 40 CD User Instructions...
Size (HxWxD) ... 88 x 220 x 365 mm (3.46” x 8.66” x 14.37”) Weight ............5.2kg (11.5lbs) Material ........Anodised aluminium chassis Cyrus reserves the right to change all specifications without notice. E &OE Acknowledgements This product uses the LVGL graphics library.
Page 15
www.cyrusaudio.com/products/40CD support@cyrusaudio.com version 1.0 www.cyrusaudio.com...
Need help?
Do you have a question about the 40 CD and is the answer not in the manual?
Questions and answers