Advertisement
The tuning machines have spring-loaded mechanisms which automatically take up wear, preventing backlash. However, it is possible to adjust the amount of pressure required to turn the machines. Each machine has a tension adjustment screw, as illustrated.
Clockwise rotation tightens the machine. The tuning machines should be adjusted to the extent that they are firm, but can turn smoothly. This adjustment is normally unnecessary, and excessive tightening can lead to premature tuning machine wear.
NOTE: Be sure to perform any necessary adjustments to the truss rod before performing the following adjustments.
String height refers to the space between the strings and frets, and has an affect on play-ability.
Set too high and the instrument is hard to play. Too low results in fret noise.
Adjust so that the space between the string and the last fret measures as follows:
Individual height adjustments for each string are provided in the form of two set screws on each saddle. Clockwise rotation raises saddle height and counter-clockwise lowers the saddle.
STRING | ||||
4-string bass | 5-string bass | 6-string bass | TUNING | HEIGHT |
— | — | 1st | High C | 2.6 mm |
1st | 1st | 2nd | G | 2.7 mm |
2nd | 2nd | 3rd | D | 2.8 mm |
3rd | 3rd | 4th | A | 2.9 mm |
4th | 4th | 5th | E | 3.0 mm |
— | 5th | 6th | Low B | 3.1 mm |
When the string gauge and/or bridge height is changed, or the truss rod is adjusted, it is usually necessary to reintonate the bridge saddles. If the bass plays out of tune in the higher registers, this adjustment is needed. Check each string in the following way:
To check intonation, compare the harmonic tone (12th fret) to the fretted tone (12th fret). Because the 12th fret is the midway point between the nut and the bridge, a harmonic tone one octave higher than the fretted tone can be generated. This is done by barely touching the string directly above the 12th fret (left hand) and simultaneously plucking the same string (right hand). If the fretted tone is exactly the same pitch as the harmonic tone, no adjustments to the bridge saddles are necessary. However, if the fretted tone is higher in pitch (sharp) or lower in pitch (flat) than the harmonic tone, apply the appropriate adjustment as shown below. Repeat the same procedure for each string.
If the fretted note is pitched higher than the harmonic, turn the corresponding saddle adjustment screw clockwise, increasing the active string length.
Conversely, if the fretted note is pitched lower than the harmonic, turn the corresponding saddle adjustment screw counter-clockwise, reducing the active string length.
The curvature of the neck should be slightly concave.
Clockwise rotation of the nut tightens the rod and corrects for too much concave bow. Counterclockwise rotation of the nut loosens the rod and corrects for too much convex bend. Make any adjustments gradually. Allow five to ten minutes for setting, and check the curvature after each 1/2 turn of the truss rod nut.
NOTE: Unless you have experience with truss rods, we suggest that you entrust this adjustment to your dealer.
The height of the pickup (i.e. distance from the strings) affects gain — the higher the pickup, the louder the sound, and vice versa. If the pickup is set too high, sustain and play-ability will suffer because of the magnetic pull on the strings. Adjust overall height using the screws located at either side of the pickup.
For optimal performance, we recommend measuring a distance of 2-3 millimeters between the bottom of string and the of the top of adjustable pole piece while fretting the highest fret.
In order to obtain maximum performance and enjoyment from this instrument, we urge you to read this Owner's Manual thoroughly before using the instrument.
After read, we recommend that you keep it in a convenient place for future reference.
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument.
Make sure to discard used batteries according to local regulations.
* When changing batteries, pay close attention to the +/- polarity markings as shown in the illustration above.
* Use only a DC9V, S-006P (6LR61 or 6F22) or equivalent battery.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the TRBX174 and is the answer not in the manual?
Questions and answers