Advertisement
Open the package and make sure it includes all below items, if any missing, please contact the reseller for replacement.
NO | Description | FUNCTION |
1 | Power Switch | Turn on/off meter |
2 | LNB IN | Connect to satellite antenna cable |
3 | LCD Screen | Video display |
4 | USB Port | Connect to PC |
5 | DC Slot | Connect to Adaptor Input |
6 | Digital tube | Quality shows |
7 | Power | Power indicator light |
8 | 22 KHZ | 22 Khz indicator light |
9 | 13V | Vertical polarization voltage output light |
10 | 18V | Horizontal polarization voltage output light |
11 | LOCK | Signal lock indicator light |
12 | Charger | Charger indicator light |
13 | OK | OK KEY |
14 | RETURN | RETURN KEY |
15 | ◄ | Right KEY |
16 | ▼ | DOWN KEY |
17 | ► | Left KEY |
18 | ▲ | Up KEY |
19 | Torch | Torch |
20 | Cover | The battery cover |
If you have installed and connected the cables of the meter, open the power switch, into the main menu.
Press the keys of to move the cursor up or down in the menu interface, then use OK key to confirm a selection
Sat Name: press key to select satellite
LNB Type: press key to select LNB Type
Low Freq: press key to select Low Freq or press OK key; then use the
key to input the value
Hi Freq: press key to select Hi Freq or press OK key; then use the
key to input the value
22K: press key to switch the 22K tone; if you select universal type the 22K setting is auto
DiSEqC1.0 1.1: press key to switch LNB port
LNB Power: press key to switch LNB power on /off.
When all of settings are ok; press RETURN key, then press OK key for save the edit.
In the first line, we can press left or right key to switch the satellite.
In the second line, we can press left or right key to switch TP; then press ok key, we can use up or down key to edit TP frequency.
In the third line, we can press ok key, then edit Symbol rate. In the fourth line, we can press left or right key to select h or v polar.
When all of settings are ok, we can check the LNB signal.
Add Satellite: the setting, refer to Antenna Setup.
Edit Satellite: press key to page up /down; then press
key to select the satellite; press ok key to edit satellite setting, refer to Antenna Setup.
Delete Satellite: refer to Edit Satellite then press ok key to delete satellite.
Please refer to Satellite Setup
Press key to move the cursor, then press OK key to select the option. Press
to input value press
to set east/west or north/south. The bottom of the screen can get the parameters of the satellite.
The first line is the SW Ver
The second line is the Hardware serial number
Set language: switch the system language
Key press Beep: switch the key Beep
Signal Lock Beep: switch beep alarm
Flashlight: switch flashlight
Signal Strength: select the signal unit
TRANSMISSION STANDARDS | |
DVB-S/S2 | |
SATELLITE INPUT / DEMODULATION | |
Connector Type | F Type |
Input Frequency | 950 to 2150 MHz |
Signal Input Level | -65 to -25 dBm |
Band Switch Control | 22 KHz |
LNB Supply | 13V/18V, IMax 300mA |
Demodulation Type | QPSK \ 8PSK |
Symbol Rate | 2<Rs<45M band (SCPC/MCPC) |
LCD FEATURES | |
LCD Type | FSTN Positive transflective |
Number of Dots | 128x64 |
Active area (WxH) | 59.6x43mm2 |
DATA SERVICE PORT | |
Connector | USB |
Data protocol | USB to RS-232 |
POWER SUPPLY | |
Li-Ion Battery | 7.4V / 800 mAh |
Adapter | OUTPUT: DC12V/1A, INTUPT: 100-240VAC 50/60Hz |
Power consumption | Max. 5W |
PHYSICAL CHARACERSTICS | |
Size (WxDxH) | 8x16x4 (cm3) |
Net Weight | 0.25 kg |
Before installation, we would like to remind you some notes, which is very important for operating safely and properly, as follows:
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the WS-6933 and is the answer not in the manual?
Questions and answers